saunalife X6 User manual

Model X6 Sauna Room
Installation Manual

Floor Raiser 1
2
Floor Raiser 2
2
Support Rail 1
4
Support Rail 2
4
Back Wall 1
1

Back Wall 2
1
Back Wall 3
1
Side Wall 1
2
Side Wall 2
1
Side Wall 3
1

Window Element 2
Door Element 1
Roof 1 1
Roof 2 2
Upper Bench 1

Lower Bench 1
Side Bench 1
Backrest 1 1
Backrest 2 1
Backrest 3 1
Bench Support 1 2
Bench Support 2 2

Side Bench Support 1 1
Side Bench Support 2 1
Backrest 2 Vertical Slat 3
Cornice Board 1 1
Cornice Board 2 2
Heater Cover 1
Front Wall Cover Slat 2

Vent Cover 1
Door Handle 1
Screws QTY
4.5 x 80mm (.19" x 3.14") 8
4.5 x 70mm (.17" x 2.75") 47
4 x 60mm (.15" x 2.36") 8
4 x 50mm (.15" x 1.96") 50
3.5 x 40mm (.13" x 1.57") 28
3.5 x 35mm (.13" x 1.37") 6
3.5 x 25mm (.13" x .98") 9
3 x 20mm (.11" x .78") 16
Vent Cover Washer 1
Tenon 8

Floor Raiser 1
Floor Raiser
Floor Raiser 2
Floor Raiser 2
Screws
4.5x80
Pre-drill holes for
the screws
Step 1. Connect the Four Floor Risers
Fasten the four Floor Risers together using 4.5x80
screws. Be sure the two shorter boards are located on
the sides and the two longer boards are on the front and
back. Use a framing square to ensure that the assembly
is square.
Support Rail 1
Tenon
Tenon
Support Rail 1
Support Rail 1
Support Rail 2
Support Rail 2
Screws
3x20
Step 2. Connect Wall Support Rails
Each wall support has a pre-drilled hole for the Tenon.
Insert the tenons in the longer support rail holes.
Fasten the Wall Support Rails together and connect
from corners using four 3x20 screws per corner.

Screws
4x50
Step 3. Position Wall Support Rails
Lay the wall support rail assembly squarely on top of the floor risers
with the groove facing up. The rails should overlap both sides of the
riser by approximately 0.5”. Secure the assembly to the floor risers
using four 4x50 screws evenly spaced on each wall support rail
Back Wall 1
Side Wall 1
Screws
4.5x70
Pre-drill the holes
for the screws
Step 4. Position Wall Sections (Back Wall 1 & Side Wall 1)
Position Back Wall 1 in the groove of the back rail and push it flush against the left
rail. Have a helper hold the back wall section. Orient Side Wall Section 1 and place
it in the groove of the left rail. Push the flat edge flush against back wall section.
Align the two panels so they are flush and fasten them using the 4.5x70 screws
Vent holes on top!

Back Wall 2
Back Wall 3
Side Wall 1
Screws
4.5x70
Side Wall 2
Window
Door Element
Screws
4.5x70
Pre-drill holes for
the screws
Step 5. Position Back Wall sections 2 & 3, & Side Wall 1
Position Back Wall 2 section into the groove of the back rail.
Attach it to Back Wall Section 1 by way of the tongue and groove fit.
Secure it by tapping it into place with a rubber mallet.
Repeat this step for wall section 3, again tapping
it into place with a rubber mallet.
Position Side Wall Section 1 into the groove
of the right side rail and push flush against
the back wall. Be sure panels are flush with
each other and fasten them together using
the 4.5x70 screws.
Step 6. Position Side Wall Section 2, Window Section & Door Element
Position Side Wall Section 2 into the groove of the side rail. Slide Side Wall Section 2 into
place with Side Wall Section 1. Section 2 connects to Section 1 via tongue and groove
so there is no need to use screws. Use a rubber mallet to secure the fit.
Place Window Section in the groove on the
front rail and push against side rail.
Being sure the two sections are flush,
fasten them together using 4.5x70 screws.
Place Door Section onto the front rail
orienting it so that the door opens
according to your preference.
Door Section connects to window section
via tongue and groove so there is no
need for screws. Gently tap it into place
with a rubber mallet to secure the fit.

Side Wall 3
Window
Screws
4.5x70
Screws
4x50
Roof Support Rail
Pre-drill holes for
the screws
Step 7. Position Window section and Side Wall section 3
Position Side Wall Section 3 into the groove of the Side Rail orienting it so that
the heater vent holes are located at the bottom. Slide the wall section into
place with Side Wall section 1. Side Wall 3 connects to Side Wall 1 via
tongue and groove so there is no need to use screws.
Use a rubber mallet to secure the fit.
Next, place Window Section into the
groove of the front rail and connect
it to Door Section via the tongue and
groove fit. Gently tap into place with
a rubber mallet to secure the fit.
Now, making sure Window Section and
Side Wall 3 are flush with each
other, secure them together
with the 4.5x70 screws.
Step 8. Assemble and Position Roof Support Rails
Reference step 2 and connect Roof Support Rails in the same way.
Place the assembly on top of the wall sections so that the wall
sections fit snugly into the groove. When in place, secure to the
assembly to the walls using four 4x50 screws on each rail.

Screws
4.5x70
Screws
4.5x70
16.1"
32.6"
20.3"
Step 9. Bench and Lower Bench installation
Use 4.5x70 screws to connect the Bench Supports to the wall. Make sure the supports in
both walls are the same height. When the supports are assembled, place the benches on
the supports. Use three 4.5x70 screws to connect the Seat Bench to the Back Wall.

2.1"
4,2"
Backrest
Screws
3.5x25
Backrest Vertical Slat
Step2
Step3
Screws
3.5x35
B
Screws
4x60
Step 10. Backrest Installation
Center the Backrest between the two sides
and position it at a height most comfortable for you
(typically 8-12” from the bench). Use a level to
ensure proper installation. Fasten the Backrest in
place using 4x60 screws. Use 3.5x25 screws to
connect the vertical slats to the backrest, refer to the
dimensions on drawings. Now attach the Backrest
between the upper and lower bench using 3.5x35
screws.
Step 1

Side Bench
Support 1
Screws
4.5x70
Side Bench
Support 2
Screws
4x60
Screws
4.5x70
Step 11. Side Bench installation
Attach the Side Bench Support 1 to the Lower Bench,
using two 4.5x70 screws. The gap between the support
and the side wall must be 2". Side Bench Support 2
connects to the window section using 4x60 screws.
Support must be in the same height with lower bench.
Place the Side Bench on the supports and fasten with two
4.5x70 screws to the side wall element.
Pre-drill holes for
the screws

C
Screws
4x60
Roof Section 1
Roof Section 2
Screws
4x50
Step 12. Lower Backrest installation
Using a level, secure the Lower Backrest to side wall
section with 4x60 screws at the same height above the
upper long bench.
Step 13. Position Roof Sections
Place the Roof Panels on top of the Ceiling Supports.
Connect the sections via the tongue and groove fit.
From the backside, roof panels must be in the same
line with ceiling supports. Position both sides equally
1.625". Connect panels with 4x50 screws.
Pre-drill holes for
the screws

Cornice Board 2
Cornice Board 1
Cornice Board 2
Screws
3.5x40
Step 14. Cornice Boards
Connect the Cornice Boards to the roof, using 3.5x40 screws.
Step 15. Vent Cover and Door Handle.
Connect Vent Cover with 3.5x40 screw. Between wall and Vent Cover
add Small Washer.
Pre-drill holes for
the screws

4x60
Screws
4x60
Screws
3.5x40
CoverCover
Slat
Step 16. Heater Cover
Connect the Heater Cover to the wall with 4x60
screws. Perform this step after heater is installed.
Note: Follow heater manufacturer recommended
installation for heater guard.
Pre-drill holes for
the screws
Step17. Cover Slats for the front wall
Connect the Cover Slats using 3.5x40 screws.
REV: X603923