Savant Netgear M4300 8x8F User manual

45 Perseverance Way, Hyannis, MA 02601
Copyright © 2017 Savant Systems, LLC
Savant.com | 508.683.2500
Video over IP Network
Netgear M4300 8x8F | M4300 12x12F | M4300 24x24F
Configuration Guide
Document Number:
009-1552-00
Document Date:
November 2017
Document Supports:
da Vinci 8.7
!

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
2of 13
Contents
1!Overview ...........................................................................................................................................................3!
2!Network Topology ........................................................................................................................................3!
3!Switch Configuration (Script).................................................................................................................. 4!
4!Switch Configuration (Manual) ................................................................................................................5!
4.1!VLAN Setup............................................................................................................................................................................. 5!
4.2!Multicast.................................................................................................................................................................................... 5!
4.3!Access Control List (ACL) Creation............................................................................................................................... 8!
4.4!Save Configuration ..............................................................................................................................................................10!
Appendix A: 10G Switch Requirements ..................................................................................................... 11!
Appendix B: Static IP........................................................................................................................................ 12!

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
3of 13
1 Overview
This document provides the necessary features/capabilities that any 10G switch needs to have to work correctly
with the Savant Video over IP System. It also provides information on how to enable these features for the 10G
switches that Savant has qualified.
2 Network Topology
Savant recommends that the 10G Switch is connected to the same switch that the Host is connected to. Unmanaged
switches should not be connected to the 10G Switch that the Video over IP system is using. The image below is a
basic network diagram.
– 10G connections to the PAV-VIMxS devices use SFP+ ports either fiber or Direct Attach Copper cables can be
used.
– 10G connections to the PAV-VOMVP1x can use either SFP+ ports with fiber cabling or RJ-45 ports with CAT-6
or above cabling, depending on the cable length.

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
4of 13
3 Switch Configuration (Script)
This is the recommended method for configuring the Netgear ProSafe switches. These steps are to be done with the
switch at its Factory default settings.
1. Download the Configuration scripts, use the Link below:
http://cdn.software.s3.amazonaws.com/scripts/Netgear/ConfigScripts.zip
2. Using Finder navigate to the download location.
3. Move the ConfigScript.zip to the Desktop of your SDE.
4. Double click on the ConfigScripts.zip to unzip the folder
5. Open the ConfigScripts folder
6. Move the Script for the switch that is in use to the Desktop.
7. Connect the upper left RJ-45 port on the Netgear switch to the main switch. Below see the port number based
on the model in use.
M4300-8X8F port 9
M4300-12X12F port 13
M4300-24X24F port 25
8. Use a network scanning software to find the IP address of the switch
9. Open Terminal on the SDE
10. Type: sh ~/Desktop/<NameOfScriptFile>.sh
Example: sh ~/Desktop/M4300-24X24F-Config.sh
11. Enter the IP Address of the Netgear switch.
Once enter is pressed the script will run and configure the switch.

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
5of 13
4 Switch Configuration (Manual)
This section gives the settings for the Savant qualified Netgear 10G ProSafe M4300 switches. Only the settings
needed for the Audio Video over IP environment are described and no other setting are noted. These steps are to
be done with the switch at its Factory default settings.
4.1 VLAN Setup
1. Connect to the Switch via a web browser.
2. Enter the User ID and Password:
Default: admin
Password: (leave, blank there is no password by default)
3. Go to Switching > VLAN
4. Add a VLAN.
5. Enter VLAN ID and VLAN Name. Below are Savant’s recommendations.
VLAN ID: 1
VLAN Name: default
6. Click Apply in the upper right corner of the browser window.
4.2 Multicast
1. Go to Switching > Multicast.
2. Click on IGMP Snooping > Multicast Router Configuration.

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
6of 13
3. Click the Check box to select all
4. Select Disable in Multicast Router.
5. Click Apply in the upper right corner of the browser window.
6. Still inside Switching > Multicast, go to IGMP Snooping > Configuration.
7. Enable Admin Mode, Validate IGMP IP header, and Proxy Querier Mode.
8. Click Apply in the upper right corner of the browser window.
9. Still inside Switching > Multicast, go to IGMP Snooping > IGMP VLAN Configuration.

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
7of 13
10. Adjust to the setting in the table below.
Category
Value
VLAN ID
1
Admin Mode
Enable
Fast Leave
Enable
Membership Interval
260
Maximum Response Time
10
Multicast Router Expiry Time
60
Report Suppression
Disable
Proxy Querier
Enable
11. Click Apply in the upper right corner of the browser window.
12. Still inside Switching > Multicast, go to IGMP Snooping > Interface Configuration.
13. Select all Ports
14. Change Admin Mode to Enabled.
15. Click Apply in the upper right corner of the browser window.
1413

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
8of 13
4.3 Access Control List (ACL) Creation
1. Go to Security > ACL
2. Click on Advance > IP ACL.
3. In the IP ACL ID field enter: 101.
4. Select Add in the top right corner.
5. Select the 101 Hyperlink that is now under “IP ACL ID”.
6. Select Add in the top right corner to start creating rules for ACL 101.

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
9of 13
7. Enter the settings shown below.
Category
Value
Sequence Number
10
Action
Deny
Match Every
False
Protocol Type
IP
Dst
224.0.0.0
0.255.255.255
NOTE: This uses a wildcard mask please use the link below to help find the
wildcard mask needed for this site.
https://www.easycalculation.com/other/subnet-mask-calculator.php
Make no other changes
8. Select Apply.

Video over IP Network Configuration Guide
Copyright © 2017 Savant Systems, LLC
009-1552-00 | 171128
10 of 13
9. Click Add in the top right corner to add permit any rule as there is an inherent deny any rule after all ACLs
Category
Value
Sequence Number
20
Action
Permit
Match Every
True
10. Select Apply.
11. Click Advanced > IP Binding Configuration.
12. Select ACL ID 101
13. Change the Direction to outbound
14. Click the port that this rule is to be applied. Below is a list by model of the Savant recommended port.
M4300-8X8F port 9
M4300-12X12F port 13
M4300-24X24F port 25
15. Select Apply in the top right corner.
4.4 Save Configuration
1. Go to Maintenance > Save Config.
2. Click Save Configuration
3. Click the Check-box
4. Click Apply in the upper right corner of the browser window.
32