Saxby Lighting Aqualine 52309 Manual

Instruction leaflet
Aqualine 24V
52309, 52310, 52311
www.saxbylighting.com
For your safety, always switch off the supply before maintaining or cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Saxby Lighting. BH23 3PE
Iss.6 26072017
Commissioning
• Ensure that all the connections are tight • Connectthepowersupplytothemainsandturnon.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 3 product and requires the use of a
LED Driver (not supplied).
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
This system operates at Safety Extra Low Voltage
(24V d.c.), via a LED driver. Never connect the LED
strips directly to the mains without using the correct
LED driver.
Always unplug the LED driver from the mains when
installing or maintaining this system.
This product contains non-replacable parts and cannot
be serviced. If damage occurs the part should be
scrapped.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
Specification
LED Drivers
LED Strips
Dimensions : 10mm wide, 3mm high x 5000mm long
Voltage : 24V
52324 : LED driver constant voltage - 100W 24V multiple output
52325 : LED driver constant voltage - 200W 24V multiple output
52309 : Aqualine 5m 5050 LED Warm White 24V
52310 : Aqualine 5m 5050 LED Cool White 24V
52311 : Aqualine 5m 5050 LED Blue 24V
Accessories
51927 : Aqualine Accessory Pack containing :-
- 2 connection leads - 12 short 4 pin connectors - 1 50cm connection cable
- 1 end cap - 16 self tapping screws
- 4 plastic tubes - 8 clips
- 4 corner connectors - 1 bottle silicone sealant
Layout
• Ensurethatyouselectthecorrectpowersupply
for the length required. If using driver 52324, this
product can be driven to a maximum length of 5m. If
using driver 52325, this product can be driven to a
maximum of 10m.
• TheAqualineLEDsaremountedonastickytape
which can be stuck to most surfaces.
• TheAqualineLEDscanbeshortenedtoaminimum
of 100mm or multiples of 100mm.
• Planthedesiredlayoutofthisfittingcarefully,
ensuring the cables will reach the distance between
the power supply and the Aqualine LEDs.
• Avoidlocatinganycablesinpositionsthatwould
cause a hazard. Position cables and Aqualine LEDs
(not supplied) away from areas where they may be
at risk from being cut, trapped or damaged.
• Cablesinwallsmustbeprotectedusingsuitable
conduit or plastic trunking.
• TheLEDstripshavespecialprotectionagainst
moisture and are IP65 rated. Please use the supplied
silicone sealant and plastic sleeves to seal the
connection joints and ends of the LED strips to
maintain IP65 protection.
• PositiontheLEDdrivernexttothemainsoutlet
socket that the system will connect to. Do not plug-
in at this stage.
• AfterdecidingthelayoutoftheLEDstrips,ensure
the cables are long enough to connect to the desired
positions.
• Cuttothedesiredlength.Themaximumpermissible
length of 24V SMD LED's for each driver is listed
in the layout section above. Ensure that the cut is
made at the copper connection points.
• Usethesuppliedsiliconesealantandplasticsleeves
to seal the connection joints and ends of the LED
strips to maintain IP65 protection.
• PeelthebackingtapeofftheAqualinestrip.Apply
moderate pressure to stick the LED's the surface.
An assistant may be required to help stick longer
lengths accurately.
• ConnectpowerleadtoendofLEDstrip-ensuring
polarity arrows line up.
• ConnectthepowerconnectortotheLEDdriver.
• Connectremotecontrolreceiverunit.
• Connectthepowersupplytothemainsandturnon.
•ForLEDstripsandconnectors:justpushtogether
to connect - use supplied brackets to secure to
mounting surface.
• ForInlineconnections:use4pinconnectors
• Forcornerconnections:usecornerconnectorsor
connection cables
• Usethesuppliedsiliconesealantandplasticsleeves
to seal the connecting joints and ends of the LED
strips to maintain IP65 protection.
Basic Installation
Connecting Strips - using accessory pack 51927 (picture above)
5000mm
Fixing Pack