Saxby Lighting Linear Pro 72364 Manual

• ConnecttheLEDdriveroutputcabletotheLEDpanel,
ensuringitissecurelyclippedtogether.
• RefittheLEDpanelanddiffuserunitbyclippingitinto
placeensuringthesidesarealignedwiththebody.Take
carenottotrapanycables.
• Refit the end caps ensuring they are clipped into
position.
• Replacefuseor circuit breakerand switch on.Your
lightisnowreadyforuse..
• TheLEDsinthisfittingarenon-replaceable.
• Ifanydamageoccursthisfittingshouldbediscarded.
Commissioning
Fitting/replacing bulbs
Instructionleaflet
Linear Pro
72364,72365,72366,72367,72368,72369
www.saxbylighting.com
Live Voltages may be present in this unit even when turned off or when completely disconnected. Foryoursafety,
alwaysswitchoffthesupplybeforecleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLighting.BH233PE
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecoulddamagethefinish.
Iss.205062018

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
This is a Class 1 product and must be earthed.
Pleasereadtheseinstructionscarefullybefore
commencinganywork.
Thisunitmustbefittedbyacompetentandqualified
electrician.
InstallinaccordancewithIEEWiringregulationsand
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
beforeinstallingormaintainingthisfitting.Ensure
otherpersonscannotrestoretheelectricalsupply
withoutyourknowledge.Ifyouareinanydoubt,
pleaseconsultaqualifiedelectrician.
Ifreplacinganexistingfitting,makeacarefulnoteof
theconnections.
Wasteelectricalproductsshouldnotbedisposedof
withhouseholdwaste.Pleaserecyclewherefacilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
ThisproductisratedatIP20.
Thislightfittingcontainsnon-replaceablepartsand
cannotbeserviced.
Ifdamageoccursthepartshouldbediscarded.
Thisproductisnotdimmable.
Specification
Voltage: 240V50Hza.c.
Lamp: 72364:31.5WLEDmodule-4100lm
 72365:47.5WLEDmodule-6200lm 
 72366:54.5WLEDmodule-7100lm
72367:57WLEDmodule-7400lm
72368:77WLEDmodule-9900lm
72369:90WLEDmodule-11500lm
IPrating: 20
Layout
• Thisproductcanbeinstalledontheceilingorwall. • Ensuretheceilingorwalliscapableofholdingthe
weightoftheproduct
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Before removing the
existing fitting, carefully note the position of each set
of wires.
• Removebothendcapsbypushingintheclipswitha
smallscrewdriverorsimilartool.
• Startingfromoneendandworkingalong,removethe
LEDpanelanddiffuserunitbygentlysqueezingthe
sidesofthemetalbodyandliftingoffthediffuserunit
tooneside.
• Holdtheproductinplaceandmarkthepositionofthe
fixingholes.Thismayrequirethehelpofanassistant.
Ifwallmounting,ensurethattheproductislevel.
• Ensuretheceilingorwalliscapableofholdingthe
weightoftheproduct.Takecaretoavoiddamaging
anyconcealedwiringandpipes.Thecorrectfixings
shouldbeusedforbrick,cavitywallsorplasterboard.
• Feedthesupplycablethroughthecentreholeandfix
thelightfittingintoposition.
• Connectthesupplycabletothequickfitterminal
blockasbelow
Installation
Wiring
Check that...
• Youhavecorrectlyidentifiedthewires
• Theconnectionsaretight
• Noloosestrandshavebeenleftoutoftheconnection
block.
Havingcorrectlyidentifiedthewiringfromyourexistinglightfitting,connecttotheconnectionblockinsidetheproduct
inthefollowingway:
PUSH DOWN