Saxby Lighting Eyot Wall EL-YG-5006 Manual

• Whenchangingabulb,alwaysswitchoffatthemains
andallowthebulbtocoolbeforehandling.Usedbulbs
shouldnotbedisposedofwithhouseholdwaste.Please
recyclewherefacilitiesexist.
• Alwaysusethecorrecttypeandwattagebulb.Usingthe
incorrectwattagebulbwilldamagethebulbandballast.
Commissioning
Fitting/replacing bulbs
Instructionleaflet
Eyot Wall
EL-YG-5006,EL-YG-5007
www.saxbylighting.com
Foryoursafety,alwaysswitchoffthesupplybeforechanginglightbulbs,orcleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilitiesexist.
CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLightingLtd.BH233PE
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecould
damagethefinish.
Glassparts–Removeandwashinwarmwaterorjustuse
adampcloth.Donotuseabrasivematerialsasthesewill
damagethefinish.
Thisbulbisprotectedbyaplasticshade.Thispartmustbereplacedimmediatelyshouldtheplastic
shadebecomecrackedordamaged.Thisfittingmustnotbeusedwithouttheplasticshadeinplace.
ReplaceCracked
Shade
• Fitthebulb,refittheplasticshade,andsecureusingthe
screws.
• Replacefuseorcircuitbreakerandswitchon.Yourlight
isnowreadyforuse.
Iss.230052014
10WG24d-12PINPLC

SUPPLY
NEUTRAL
LIGHTFITTING
BLUE(N)
EARTH(GREEN/YELLOW) GREEN/YELLOW
BROWN(L)
SWITCHEDLIVE
Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeandsatisfactory
operationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
This light fitting is Class 1 and must be connected to
an Earth circuit
Pleasereadtheseinstructionscarefullybefore
commencinganywork.
Thisunitmustbefittedbyacompetentandqualified
electrician.
InstallinaccordancewithIEEWiringregulationsand
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
beforeinstallingormaintainingthisfitting.Ensureother
personscannotrestoretheelectricalsupplywithout
yourknowledge.Ifyouareinanydoubt,pleaseconsulta
qualifiedelectrician.
Thislightfittingshouldbeconnectedtoacircuitwitha
30mARCDfitted.
Ifreplacinganexistingfitting,makeacarefulnoteofthe
connections.
Alwaysusethecorrecttypeandwattagebulb.Usingthe
incorrectwattagebulbwilldamagethebulbandballast.
Whenchangingabulb,alwaysswitchoffatthemainsand
allowtheoldbulbtocooldownbeforehandling.Dispose
ofusedbulbscarefullyandresponsibly.
Wasteelectricalproductsshouldnotbedisposedofwith
householdwaste.Pleaserecyclewherefacilitiesexist.
Checkwithyourlocalauthorityorretailerforrecycling
advice.
ThisproductisratedatIP44.
Thisproductisnotsuitablefordimming.
Thisproductisnotsuitableforlocationinorneara
marineorseaenvironment.
Theentireunitgetshotwhilstonforaperiodoftime.
TheseproductsshouldnotbefittedtoPIRcircuitsorshort
durationtimedswitches.Shouldyouwishtoconnectthis
unittoatimedsystempleaseconsultthemanufacturer
beforeinstallation.
Specification
Voltage: 240V50Hza.c.
Lamp: 1x10WG24d-1PLC2pin
IPrating: 44
Layout
Installation
Havingcorrectlyidentifiedthewiringfromyourexisting
lightfittingandconnecttotheconnectionblockinsidethe
productinthefollowingway:
Wiring
Check that...
• Youhavecorrectlyidentifiedthewires.
• Theconnectionsaretight.
• Noloosestrandshavebeenleftoutoftheconnection
block,andallexposedareasoftheconnectionblockare
coveredwithtwolayersofinsulationtape.
• Planthedesiredlayoutofthisfittingcarefully,ensuring
thecableswillreachthedistancebetweenthejunction
boxandthelightfitting
• Avoidlocatinganycablesinpositionsthatwould
causeahazard.Positioncablesandjunctionboxes(not
supplied)awayfromareaswheretheymaybeatrisk
frombeingcut,trappedordamaged
• Cablesinwallsmustbeprotectedusingsuitable
conduitorplastictrunking.
• Themainssupplycablemusthaveaminimumcross
sectionalareaof1.0mm²
• Thisproductmustonlybefittedwiththelampholder
facingupwards.
• Thisproducthasspecialprotectionagainsttheingress
ofmoistureandisIP44rated.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Beforeremovingtheexisting
fitting,carefully note the position of each set of wires.
• Undothe3screws,andremovethefrontcover(Fig.1).
Retainscrewsforfutureuse.
• Holdthewallbackinplaceandmarkthepositionofthe
holes.Ensurethattheproductislevel.
• Ensurethewalliscapableofholdingtheweightofthe
product.Takecaretoavoiddamaginganyconcealed
wiringandpipes.Thecorrectfixingsshouldbeusedfor
brick,cavitywallsorplasterboard.
• Piercegrommetandpassthesupplycablethroughthe
holeinthewallback.
• Fixthewallbackintopositionusingthesuppliedscrews
(Fog.2)andwireasbelow.
Fig2.
Fig1.