SC&T HE01SI User manual

Smart Cabling & Transmission Corp.
V1.0_1604120
HDMI Extender
User Manual
Model : HE01SI
HDMI & IR CAT5e Extender 1080p 40M

1
User Manual
HE01SI
Introduction
HE01SI is an HDMI extender that uses an Ethernet cable to extend HDMI signal with transmission distance
up to 70 meters and resolution up to 1080p. The extender transmits a 2-way IR signal from either TX or RX
side. The Tx unit has a built-in EDID auto backup function that can save desired resolution and restore it
whenever.
Features
Resolution up to 1080p@60Hz.
Signal extension up to 70M over CAT5e cable.
Supports IR extension, the signal from either TX or RX side.
Built-in EDID auto backup function at RX unit.
Installation view
Panel View & Function
HE01SIT
EDID Setup
Use default EDID:
Move DIP switch 1 off ↑
Move DIP switch 2 off ↑Select the first default EDID: support 1080i / LPCM 2 Channel.
Move DIP switch 2 on ↓Select the second default EDID: support 1080p / LPCM 5.1 Channel.

2
User Manual
HE01SI
Use External EDID
1. Move DIP switch 1 on↓, HE01SIT unplug the power.
2. HE01SIT connect to HDMI connector of TV for auto backup.
3. Plug the power for HE01SIT, TV EDID back up completed (Blue Power LED keep flash)
4. After complete TV EDID backup, HE01SIT power must be reset (unplug and plug) to activate the
new EDID.
HE01SIT Transmitter Unit LED Indication
BLUE ON Power on
Flash TV EDID backup completed
RJ45 Connector LED
GREEN ON Sending power or video to receiver unit
YELLOW ON No data input or unsupported video format
Dip Switch function
1. ↑Use the default EDID.
↓Use the backup TV EDID.
2. ↑Select the first default EDID: Support 1080i / LPCM 2 Channel.
↓Select the second default EDID: Support 1080p / LPCM 5.1 Channel.
After complete Dip Switch setting, power must be reset (Unplug and plug) to activate the new EDID.
HE01SIR
HE01SIR Receiver unit LED Indication
BLUE ON Using external power adapter
GREEN ON Power and HDMI signal received from transmitter unit
YELLOW ON No data input or signal too weak

3
User Manual
HE01SI
IR Switch Setting
1. When use BD/DVD remote controller (DVD at remote side)，HE01SIR IR switch move to RX and connect
with Receiver cable; HE01SIT IR switch move to TX and connect with Emitter cable.
2. When use TV remote controller (TV at remote side), HE01SIT IR switch move to RX and connect with
Receiver cable; HE01SIR IR switch move to TX and connect with Emitter cable.
Cable
Link cable use high quality CAT5e UTP or CAT6 UTP cable.
CAT6 cable is recommend based on distance over 30 meters.
Do not use STP cable which caused no picture.
Transmission Distance
The transmission distance will be affected from different HDMI equipment and cable quality.
HE01SIT to HE01SIR
Resolution/Cable
Distance(Meter)
1080p/CAT5e
40
1080p/CAT6
45
1080i,720p/CAT5e
70
RJ45 Define
Video Link (use TIA/EIA-568-B)
1. Orange-white
TMDS DATA2 +
2. Orange
TMDS DATA2 -
3. Green-white
TMDS CLOCK + / HDMI 5V
4. Blue
TMDS DATA1 +
5. Blue-white
TMDS DATA1 -
6. Green
TMDS CLOCK - / HDMI 0V
7. Brown-white
TMDS DATA0 +
8. Brown
TMDS DATA0 -

4
User Manual
HE01SI
Caution
1. The wiring must away from any equipment with electromagnetic wave, i.e.:
Mobile phone, microwave, radio equipment, fluorescent lamp, power lines.
2. If distance less 20meters and not using IR function, HE01SIR do not need external power adapter.
3. This device is not network device, do not connect with Network to avoid damage.
Specification
ITEM NO.
HE01SIT
HE01SIR
Support
Compliance
HDMI 1.3, HDCP, 3D
Max. Video Resolution
1080p@60Hz
Max. Transmission Distance
60M at 1080i, 40M at 1080p
IR Support
30-60KHz, ±30°, 5M
30-60KHz, ±55°, 5M
Ports & Interfaces
Video Input
1 x HDMI Type A
1 x RJ45
Video Output
1 x RJ45
1 x HDMI Type A
IR Interface
1 x 3.5mm Phone Jack
1 x 3.5mm Phone Jack
Switch
1 x 2 Pin Dip Switch, 1 x Slide
Switch
1 x Slide Switch
Power
Power Supply
DC 5V 1A
DC 5V 1A
Power Consumption
420mA
180mA
Ambient Temperature
Operation
0 to 55℃
Storage
-20 to 85℃
Humidity
up to 95%
Physical Characteristics
Dimensions
67 x 102 x 27mm
67 x 91 x 27mm
Weight
150g
140g