SC&T IP09 User manual

Smart Cabling & Transmission Corp.
V1.0_2001100
IP/ PoE Extender
User Manual
Model : IP09
Ethernet over CAT5e Extender

1
User Manual
IP09
Introduction
IP09 is an IP extender that can use a single CAT5e (or greater) cable to send TCP/IP signal to a remote
IP-enabled device, with transmission distance up to 800M and bandwidth up to 100Mbps. Furthermore,
the high bandwidth allows IP09 to send multiple IP signals over one Ethernet cable and split these signals
for different IP devices. It's perfect solution for CCTV security system to extend IP cameras to a remote
NVR for recording.
Features
Signal Extension up to 800M over CAT5e.
Bandwidth up to 70Mbps.
Able to send multiple IP signals over single Ethernet cable.
Supports Auto MDI/MDI-X and full/ half duplex mode.
Built-in 1.5KV (Line to Line) surge protection.
Transmission Distance Chart
The transmission distance report below is tested through the COMMSCOPE 57535-2 (CAT5e 24AWG)
cables.
Mode
Data Rate
Transmission Distance
100BASE-TX
100Mbps
130M
100BASE-T1
100Mbps
300M
Long Reach 100
100Mbps
500M
10BASE-T
10Mbps
250M
Long Reach 10
10Mbps
800M
※The distance may vary by installation conditions, quality of cables, and the performance of
connecting devices.
※10BASE-T / 100BASE-TX and Long Reach 100Mbps mode use 2 pair wire to transmit
※100BASE-T1 and Long Reach 10Mbps mode use 1 pair wire to transmit only

2
User Manual
IP09
Installation View
(1) Point to Point Transmission
(2) Multi-Camera Video Transmission
(3) Wifi Acess Point Extending Transmission

3
User Manual
IP09
(4) Extra Long Distance Transmission
(5) Extra Long HDMI Transmission
Panel Review

4
User Manual
IP09
No.
Interface
Functionality
1
RJ45 Connector
Port 1；To connect networking devices or another IP09
(Refer to Description 1,2,3)
2
RJ45 Connector
Port 2；To connect networking devices or another IP09
(Refer to Description 1,2,3)
3
RJ45 LED
To indicate the network connection status
(Refer to Description 4)
4
Power Jack
To connect DC12V 0.5A adapter
5
Power LED Indication
To indicate the power status (Refer to Description 5)
6
Status Indication
□
1Status : Port 1 mode indication (Refer to Description 6)
□
2Status : Port 2 mode indication (Refer to Description 6)
7
DIP Switch
To select the desired mode (Refer to Description 7)
Description
1. Link speed of port 1 and 2 must be sync, or they are not able to activate network connection.
2. Once the port 1 and 2 remain unlinked, the IP09 will automatically turn to Power Saving mode.
3. RJ45 Pinout
4. RJ45 LED
Data Rate
LED On
LED Off
LED Blinking
100Mbs
Enable
Disable
Data Transferring
10Mbps
Enable
Disable
Data Transferring
5. Power LED Indication
Green On
Green Off
Light Breathing
Power On
Power Off
Power Saving
(PIN TIA/EIA-568B)
PIN
Wire Color
1
Orange-white
2
Orange
3
Green-white
4
Blue
5
Blue-white
6
Green
7
Brown-white
8
Brown

5
User Manual
IP09
6. Status Indication
Blue On
Blue Off
Light Blinking
Blink twice
Long Reach
Ethernet
100BaseT-T1
Hardware Failure
7. Dip Switch Setting:
7.1. Auto Mode / Default (Highly Recommended)
Dip switch 1-2-3-4 all up (OFF)
Auto Mode enable auto negotiation which automatically set up the link speed and
transmssion protocol.
7.2 Auto+EEE Mode
Dip switch 1 down (ON), 2-3-4 up (OFF)
Auto+EEE mode supports Energy-Efficient Ethernet based on Auto Mode.
7.3 Advanced Mode
Please refer to the chart below to manually set up the Link Speed, and Modes
No.
Mode
↑OFF
↓ON
1
LINK SPEED
10Mbps
100Mbps
2
ETHERNET
Disable
Enable
3
100BASE-T1
Disable
Enable
4
LONG REACH
Disable
Enable
※Link speed of 10Mbps is not supported on 100BASE-T1 mode
Auto-Negotiation Priority
Priority
Mode
1 (Highest)
Long Distance 100Mbps
2
100BASE-T1
3
Long Distance 10Mbps
4
100BASE-TX Full Duplex
5
100BASE-TX Half Duplex
6
10BASE-T Full Duplex
7 (Lowest)
10BASE-T Half Duplex

6
User Manual
IP09
IP09K Package Included
2 x IP09.
2 x DC12V 0.5A Power Adapter.
4 x Screw
4 x Screw Plug

7
User Manual
IP09
Specification
ITEM NO.
IP09
Support
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3bw 100BASE-T1 Ethernet
IEEE 802.3 Nway Auto-Negotiation
IEEE 802.3x Full Duplex Operation And Flow Control
IEEE 802.3az Energy Efficient Ethernet
Network Bandwidth
10/ 100Mbps
Max. Transmission Distance
800M at 10Mbps, 500M at 100Mbps
Ports & Interfaces
Input
1 x RJ45
Output
1 x RJ45
Power Interface
2 x (2mm) DC Jack
Power
Power Supply
DC 12V 500mA Regulated
Power Consumption
1W (Max)
Ambient Temperature
Operation
0 to 55℃
Storage
-20 to 85℃
Humidity
Up to 95%
Physical Characteristics
Dimensions
49 x 91.8 x 25mm
Weight
120g

8
User Manual
IP09