SC&T IP09P User manual

Smart Cabling & Transmission Corp.
V1.0_
201210M
IP/ PoE Extender
User Manual
Model : IP09P
PoE over CAT5e Extender

1
User Manual
IP09P
Introduction
IP09P is a point-to-point PoE (Power over Ethernet) extender that can use single CAT5e (or greater) cable
to extend TCP/IP signal and huge amount of power for a remote PoE device, such as speed dome
camera, Dante PoE speaker, smart LED…etc., with no external power required. It’s a perfect solution for
CCTV system, large-scale audio environment, smart building and factory.
Features
Signal extension up to 800M over CAT5e cable.
Provides up to 90W power for remote PoE device.
Power source from either a PoE switch or an external power adapter.
Bandwidth up to 100Mbps.
Supports Full duplex and half duplex mode and Auto MDI/MDI-X switching.
Built-in 30kV ESD, 40A EFT, and 30A surge at RJ45 side.
Installation view
1 Power from a PoE switch
2 Power from a power adapter

2
User Manual
IP09P
3 Extra Power supply at the transmitter side for additional 100M extension
4 Extra-long distance PoE Extension

3
User Manual
IP09P
Panel Review
No.
Interface
Function
1
Power Jack
To connect with DC48 or 56V power adapter when
connecting to non-PoE device. Power input maximum up to
110W.
2
Power LED Indication
To indicate the power status (Refer to Description 1)
3
Port 1 Status Indication
Port 1 mode indication (Refer to Description 3)
4
Port 2 Status Indication
Port 2 mode indication (Refer to Description 3)
5
Console Port
To update firmware.
6
DIP Switch
To select the desired mode (Refer to Description 5)
7
RJ45 Connector
Port 1；To connect with an networking device or IP09P
(Refer to Description 4)
8
RJ45 Connector
Port 2；To connect with IP09PT/ IP09PR
9
PoE LED Indication
To indicate the PoE connection status (Refer to Description 2)

4
User Manual
IP09P
Description
1Power LED Indication
Green ON
Green OFF
Breathe
Power On
Power Off
Power Saving
2PoE LED Indicator
Blue ON
Blue OFF
Connect to PoE device
Connect to Non-PoE device
3Status Indication
Port □
1Status
Blue ON
Blue OFF
Light Blinking
Blink twice
Long Distance
Unlinked or Ethernet
100Base-T1
Hardware Failure
Port □
2Status
Blue ON
Blue OFF
Light Blinking
Blink twice
Long Distance
Unlinked
100Base-T1
Hardware Failure
3.1 Once the port 1 and 2 remain unlinked, the IP09C will automatically turn to Power
Saving mode.

5
User Manual
IP09P
4RJ45 Pinout
4.1 1
0BA
SE-T,
100B
ASE-
TX
and
long
dist
ance 100Mbps mode use two pairs of wires to transfer data.
4.2 100BASE-T1, long-distance 10Mbps mode use one pair of wires to transfer data.
4.3 Power is transferred through four pairs of wire.
568B Pinout
Order
RJ45 Port 1 (Black)
RJ45 Port 2 (Yellow)
Data
PoE
Data
PoE
1. Orange-white
TX+ (DATA1+)
PoE+ (Data Pair)
DATA1+
Power +
2. Orange
TX- (DATA1-)
PoE+ (Data Pair)
DATA1-
Power +
3. Green-white
RX+ (DATA2+)
PoE- (Data Pair)
DATA2+
Power -
4. Blue
PoE+ (Spare Pair)
Power +
5. Blue-white
PoE+ (Spare Pair)
Power +
6. Green
RX- (DATA2-)
PoE- (Data Pair)
DATA2-
Power -
7. Brown-white
PoE- (Spare Pair)
Power -
8. Brown
PoE- (Spare Pair)
Power -

6
User Manual
IP09P
5Power and Transmission Distance
The reports below show the extension distance and the amount of power transferred by distance. All
statistics get from the result of using the COMMSCOPE 57535-2 (CAT5e 24AWG) cables to test.
5.1 Mode & Data Rate by transmission distance
5.2 Power from 56V Power Adapter
Input Power
Distance
Output Power
95W (56V/1.7A)
200M
50W
72W (56V/1.3A)
300M
38W
56W (56V/1.0A)
400M
29W
45W (56V/0.8A)
500M
23W
40W (56V/0.7A)
600M
20W
32W (56V/0.57A)
700M
16W
28W (56V/0.5A)
800M
14W
5.3 Power from 48V Power Adapter
Input Power
Distance
Output Power
64W (48V/1.4A)
200M
36W
44W (48V/0.9A)
300M
24W
34W (48V/0.7A)
400M
19W
29W (48V/0.6A)
500M
15W
22W (48V/0.45A)
600M
12W
21W (48V/0.44A)
700M
10W
17W (48V/0.35)
800M
8W
Mode
Data Rate
Distance
100BASE-TX with EEE
100Mbps
100M
100BASE-TX
100Mbps
130M
100BASE-T1
100Mbps
300M
Long Distance
100Mbps
500M
10BASE-T with EEE
10Mbps
100M
10BASE-T
10Mbps
250M
Long Distance
10Mbps
800M

7
User Manual
IP09P
5.4 Power from IEEE 802.3at PoE Switch
Input Power
Distance
Output Power
IEEE 802.3at
PoE Switch
200M
21W
300M
19W
400M
17.5W
500M
16.5W
600M
15W
700M
13W
800M
10W
6DIP Switch Setting
6.1 Port 1 can be set manually and automatically but Port2 can only set automatically.
6.2 Auto Mode/ Default: Automatically set up the link speed and transmssion protocol.
6.3 Auto+EEE Mode: Energy-Efficient Ethernet based on Auto Mode.
6.4 When all DIP switches are ON, the data rate will support 100Mbps at all modes.
6.5 When Switch 1 is OFF and Switch 2, 3, 4 are ON, the data rate will support 10Mbps at all
modes.
6.6 When data rate is 10Mbps at 100BASE-T1 mode, the mode will automatically switch to
Long-Distance mode and data rate remains 10Mbps.
6.7 Port 2 will auto-negotiate to perfect the connection.
6.8 When Port 1 is connected with a networking device over 500M away or the auto-mode
cannot work properly, please follow the chart below to manually set up data rates and
modes.
SWITCH
SETTINGS/ FUNCTION
SW 1
Auto Mode
(Default)
OFF↑
Auto Mode
with EEE
ON↓
ON↓
OFF↑
SW 2
OFF↑
OFF↑
ON↓
ON↓
SW 3
OFF↑
OFF↑
ON↓
ON↓
SW 4
OFF↑
OFF↑
ON↓
ON↓
SWITCH
Function
↑OFF
↓ON
SW 1
Link Speed
10Mbps
100Mbps
SW 2
Standard Ethernet
Disable
Enable
SW 3
100BASE-T1
Disable
Enable
SW 4
Long Distance
Disable
Enable
100Mbps
10Mbps

8
User Manual
IP09P
6.9 Port 1 Auto-Negotiation Priority
Priority
Mode
1 (Highest)
Long Distance 100Mbps
2
100BASE-T1
3
Long Distance 10Mbps
4
100BASE-TX Full Duplex
5
100BASE-TX Half Duplex
6
10BASE-T Full Duplex
7 (Lowest)
10BASE-T Half Duplex

9
User Manual
IP09P
Jumper Settings
1. We strongly recommend those who have advanced engineering skills to adjust the jumpers.
2. Improper adjustment may make the devices damaged.
3. Any changes should start after turning off the power.
4. IP09PT Jumper Settings:
Position
Function
Setting
Description
P3
Operation Mode
Jumper cap on pin 1 & 2
PoE handshake ON (Default)
Jumper cap on pin 2 & 3
PoE handshake OFF
P4
Data Pair A
Power Settings
Jumper cap ON
Mode A
(End-spin)
Power over PIN 1,2 (Default)
Jumper cap OFF
Power OFF
P5
Data Pair B
Power Settings
Jumper cap ON
Power over PIN 3,6 (Default)
Jumper cap OFF
Power OFF
P6
Spare Pair C
Power Settings
Jumper cap ON
Mode B
(Mid-spin)
Power over PIN 4,5 (Default)
Jumper cap OFF
Power OFF
P7
Spare Pair D
Power Settings
Jumper cap ON
Power over PIN 7,8 (Default)
Jumper cap OFF
Power OFF
P8
PoE Mode
Jumper cap on pin 1 & 2
On Standard PoE Mode (Default)
Jumper cap on pin 2 & 3
On Legacy PoE Mode
P9
Dual PD Mode
Jumper cap on pin 1 & 2
Power over 8 PINs (Default)
Jumper cap on pin 2 & 3
Dual PD mode OFF
P10
Boost Voltage
Jumper cap on pin 1 & 2
Enable boost voltage (Default)
Jumper cap on pin 2 & 3
Disable boost voltage
P11
Voltage Select
Jumper cap on pin 1 & 2
Boosted voltage for PSE (Default)
Jumper cap on pin 2 & 3
No boost voltage for PSE

10
User Manual
IP09P
IP09PR Jumper Settings
Position
Function
Setting
Description
RP3
Operation Mode
Jumper cap on pin 1 & 2
PoE power ON (Default)
Jumper cap on pin 2 & 3
PoE power OFF
RP4
PoE Class Setting
Jumper cap on pin 1 & 2
Support 802.3bt 90W (Default)
RP5
Jumper cap on pin 2 & 3
Support 802.3bt 60W
Package Included
1 x IP09PT
1 x IP09PR
4 x Screw
4 x Screw Plug

11
User Manual
IP09P
Specification:
ITEM
IP09PR
IP09PT
Support
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3bw 100BASE-T1 Ethernet
IEEE 802.3 N-Way Auto-Negotiation
IEEE 802.3x Full Duplex Operation and Flow Control
IEEE 802.3az Energy Efficient Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Network Bandwidth
10/ 100 Mbps
Max. Transmission Distance
10Mbps at 800M, 100Mbps at 500M
Ports & Interfaces
Input
1 x RJ45
1 x RJ45
Output
1 x RJ45
1 x RJ45
Power Interface
1 x (5.5 x 2.1mm) DC Jack
Power
Power Supply
DC 48 ~ 56V Regulated
DC 12 ~ 56V Regulated
Power Consumption
1W
1W
Ambient Temperature
Operation
0 ~ 85℃
Storage
-20 to 85℃
Humidity
95%
Physical Characteristics
Dimensions
67 x 135 x 27mm
67 x 135 x 27mm
Weight
205g
215g