Scantool WSP 15F User manual

Industrivej 3-9
DK-9460 Brovst
Denmark
Tlf.: [phone]
Fax: [phone]
Operators Manual:
WSP 15F
15 TON
FOOT/MANUAL SHOP PRESS

2
EC declaration of conformity
hereby declares that
SCANTOOL Press WSP 15F are manufactured in accordance with
the provisions of the European Parliament and Council Directive
2006/42 / EC of 17 May 2006
SCANTOOL A/S
Industrivej 3-9
9460 Brovst
Denmark
Ph.: [phone]
Fax: [phone]
Website: www.scantool-group.com

3
Contents
1.0 SAFETY INSTRUCTIONS AND WARNINGS 4
2.0 SPECIFICATIONS 5
3.0 BEFORE FIRST USE 5
4.0 OPERATION 5
5.0 TROUBLE SHOOTING 5
6.0 MAINTENANCE 6
7.0 DRAWINGS AND SPARE PARTS LISTS 7
8.0 DIMENSIONS 10
9.0 GUARANTEE 11

4
Instruction Manual
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFETY INSTRUCTIONS N
WARNINGS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT
IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE TO PROPERTY AND/OR SERIOUS
PERSONAL INJURY. PLEASE KEEP THIS INSTRUCTION MANUAL SAFE FOR FUTURE USE.
1.0 SAFETY INSTRUCTIONS AND WARNINGS
1.1 Use a qualified person to maintain the press in good condition. Keep it clean for best
and safest performance.
1.2 The maximum load is 15tons. DO NOT exceed this rated capacity. Never apply
excessive force to a work piece and always use the pressure gauge to accurately
determine the applied load.
1.3 Use this press for the purpose for which it is intended. DO NOT use it for any other
purpose it is not designed to perform.
1.4 Keep children and unauthorized persons away from the work area.
1.5 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewelry, and
contain long hair.
1.6 Wear ANSI approved impact safety goggles, full-face impact safety shield and
heavy-duty work gloves when operating the press.
1.7 Keep proper balance and footing, do not overreach and wear nonslip footwear.
1.8 Only use this press on a surface that is stable, level, dry and not slippery, and
capable of sustaining the load. Keep the surface clean, tidy and free from unrelated
materials and ensure that there is adequate lighting.
1.9 Inspect the press before each use. DO NOT use if bent, broken, cracked, leaking or
otherwise damaged, any suspect parts are noted or it has been subjected to a shock
load.
1.10 Check to ensure that all applicable bolts and nuts are firmly tightened.
1.11 Ensure that work piece is center-loaded and secure.
1.12 Keep hands and feet away from bed area at all times.
1.13 DO NOT use the shop press to compress spring or any other item that could
disengage and cause a potential hazard. Never stand directly in front of loaded press
and never leave loaded press unattended.
1.14 DO NOT operate the press when you are tired or under the influence of alcohol,
drugs or any intoxicating medication.
1.15 DO NOT allow untrained persons to operate the press.
1.16 DO NOT make any modifications to the press.
1.17 DO NOT use brake fluid or any other improper fluid and avoid mixing different types
of oil when adding hydraulic oil. Only good quality hydraulic jack oil can be used.
1.18 DO NOT expose the press to rain or any other kind of bad weather.
1.19 If the press need repairing and/or there are any parts that need to be replaced, have
it repaired by authorized technicians and only use the replacement parts supplied by
the manufacturer.
1.20 WARNING: the warnings, cautions and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which cannot
be built into this product, but must be supplied by the operator.

5
2.0 SPECIFICATIONS
Capacity 15ton Stroke 160mm
Working Range 168-980mm Bed width 500mm
3.0 ASSEMBLY
Use the exploded drawing as your guide to assemble the press. Lay all parts and
assemblies out in front of you before beginning. The following procedure is recommended:
3.1 Attach one base section (11) to left post (15) using bolts (9), washers (12), lock
washers (13) and nuts (14) then attach another to right post (15)
3.2 Insert bed frame pins (8) into the holes in the posts, and then insert the joined press
bed frame (6) into press frame and onto bed frame pin.
3.3 Attach the pump and protection cover assemblies to the right post using bolts (16)
and washers (12), Connect the oil hose 2 (39) to the directing fitting (30) and
assemble the pressure gauge (38) to the union seat (34) and oil hose 1 (27)
connection the union seat(34) and ram (26)
3.4 Tighten all bolts and nuts.
4.0 BEFORE FIRST USE
4.1 Purge away air from the hydraulic system.
Manual operation system: open the long release valve (P27) and short release
valve (P33) by turning it counterclockwise. Pump several full stokes to eliminate any
air in the system.
4.2 Check all parts and conditions, if there is any part broken, stop using it and contact
your supplier immediately.
5.0 OPERATING INSTRUCTIONS
WARNING! Ensure that you read, understand and apply the safety instructions and
warnings before use.
WARNING! Ensure that you have familiarized yourself thoroughly with the product
and the hazards associated with its improper use.
5.1 Place the heel block (4) onto the press bed frame (6), then insert work piece onto the
heel block.
5.2 Close the long release valve (P27) and short release valve (P33) by turning it
clockwise until it is firmly closed. Use the foot (47) or handle (54) let the piston rod
fast down, when the serrated saddle contact pressure was objects, open the short
release valve (P33) ,that enables you to use more energy .
5.3 Align work piece and ram to ensure center-loading.
5.4 Once ram has fully retracted, remove work piece from the press bed frame.

6
6.0 MAINTENANCE
6.1 Clean the outside of the press with dry, clean and soft cloth and periodically lubricate
the joints and all moving parts with light oil as needed.
6.2 When not in use, store the press in a dry location with ram and piston fully retracted..
6.3 When press efficiency drops, purge away air from hydraulic system as described in
4.1
6.4 Check the hydraulic oil level: remove the filler nut (P34) on the top of the reservoir, if
the oil is not adequate, fill with high quality hydraulic jack oil as necessary, then
replace the oil filler nut, purge away air from the hydraulic system as described in 4.1

7
7.0 DRAWINGS AND SPARE PARTS LISTS

8

9

10
8.0 DIMENSIONS

11
9.0 GUARANTEE
If within 2 year of purchase this machine supplied by SCANTOOL A/S becomes defective
due to faulty materials or workmanship we guarantee to repair or replace the machine or
defective part or parts free of charge provided that:
1 The product is returned complete to one of our Service Branches or Official Service
Agents.
2 The product has not been misused or carelessly handled and in particular has not
been used in a manner contrary to the operating instructions.
3 Repairs have not been made or attempted by other than our own Service Staff or the
staff of our Official Service Agents.
4 Documentary proof of purchase date is produced when the goods are handed in or
sent for repair.
5 Wear parts are not covered by the warranty