Schacht WOLF PUP 8.10 User manual

WOLF PUP 8.10 &
PUP 8.10 STROLLER
Special aSSembly
inStructionS
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273
© 2017 Schacht Spindle Company, Inc. 08.17
open - ready to weavefolded - ready to travel
For WolF pup Sold prior to (8.10 releaSe)
and WolF pup 8.10 W/Hgt extender Sold prior to 8/24/17

– 2 – – 3 –
WOLF PUP 8.10 STROLLER
aSSembly inStructionS
PARTS LIST
4 – caster blocks with casters
2 – stroller support bars
2 – ¼" x 3" trusshead machine screw
2 – ¼” x 3 ½" trusshead machine screw
4 – ¼" x 2 ¼" carriage bolts
2 – ¼" x 1 ½" hex bolts
2 – ¼" x 1 ¾" hex bolts
1 – 3 /8" x 3 ½" hex bolt
8 – ¼" washers
1 – 3
/8" washer
8 – ¼" lock nuts
2 – ¼" wing nuts
TOOLS
Phillips screwdriver
Flat screwdriver
drill w/ 1/4" bit
Rubber mallet or hammer
Piece of scrap wood
NOTE: Wolf loom legs are called out by where they cross each other. The legs
that touch the ground at the front of the loom are called “inside” legs because
they are covered by the “outside” legs when they cross at the loom center.
screw though the caster block and height
extender (if attached) into the treadle bar
(Figure 2). Using a at screwdriver to hold
the barrel nut in place, tighten the bolt
into the barrel nut. Repeat for the other
front caster block.
4. Attach the caster blocks to the outside
legs and the rear leg brace. Remove the
trusshead bolts (D) holding the rear leg
brace to both outside legs (Figure 1).
5. Attach the right rear caster block
with the new 4" machine screw through
the bottom hole (C) and the caster wheel
towards the back and on the oor (Figure
3). Tighten the bolt into the barrel nut so
that the stroller rotates, but is not loose.
1. Install the wolf stroller on a hard
surface. Open the loom to weaving
position (see front cover illustration).
2. Attach the stroller caster blocks to the
inside legs and the treadle bar. Locate
the trusshead bolt (B) that attaches the
inside leg height extender to the treadle
bar (Figure 1). Remove the bolt from the
leg. The barrel nut that held the bolt slips
out of the underside of the treadle bar.
Discard the bolt and keep the barrel nut.
3. Set a caster block on the outside of
the leg, with the caster wheel toward the
front and on the oor. Line up the hole
(C) at the bottom of the block to the hole
(B) in the leg and insert a new 4” machine
FIGURE 1
treadle bar
rear leg
brace
barrel nut barrel nut
B
H H D
inside leg on
right side of loom
outside leg on
right side of loom

– 2 – – 3 –
6. Drill upper hole to secure rear caster
blocks. Assemble the black plastic washer
onto the 2-1/2" machine bolt. Slide the
bolt through hole (G) from the inside of
the loom, and tighten a wing nut down on
the exposed bolt
7. Rotate the caster block until the black
plastic washer comes to rest as a stop
against the loom leg. Clamp the caster
into this position.
8. Using the top hole (A) as a drill guide,
drill a 1/4" hole through the height
extender and/or the outside rear leg.
Remove the plastic washer, bolt, and wing
wing nut and repeat for the caster on the
left outside leg.
9. Attach the top of the casters to the loom
legs. Put a 2 ¼" carriage bolt through the
holes (H) in the legs from the inside, then
through the top hole (A) in the caster
blocks (Figure 4). Tap the carriage bolt
into the loom leg using a rubber mallet or
hammer and a piece of scrap wood. Place
a washer and a lock nut on the carriage
bolt and tighten the lock nut enough to
draw the head of the carriage bolt into the
wood of the leg.
10. Attach the metal support bar to the
rear caster block. From the inside of the
loom, insert a 1 ½" hex bolt through the
hole (G) in the rear caster block. Place
a washer on the bolt and then place the
circular hole at the end of the metal
support bar over the bolt so that the jog
in the bar points outward. Secure with
another washer and a lock nut. Tighten
the lock nut, allowing the support bar to
still pivot freely (gure 4). Repeat for the
other rear caster block.
FIGURE 4
G
stroller
support bar
FIGURE 2
A
C
G
4" machine screw
FIGURE 3
A
H
H
A
G

– 4 – – PB –
11. Attach the bolt to hold the front of the
metal support bar when the loom is folded.
(gure 4) From the inside of the loom
insert a 1 ¾" hex bolt through the hole
(G) in the front caster block. Secure the
hex bolt with a washer and a lock nut.
Place a ¼” wing nut on the bolt. Repeat
Step 5 for the other front caster block.
12. Using the stroller. (gure 5) Fold the
loom. Tighten the fold-up knobs and
secure the slide lock bars to prevent the
loom from opening. You will notice that
the loom is now sitting on its stroller
wheels. Remove the wing nut from the
bolt at (G) on the front caster blocks.
Place the slots at the front end of each
metal support bar over these bolts, replace
the wing nuts and tighten.
Your Wolf loom is now ready to travel. •
ADDITIONAL WEAVING ACCESSORIES
WOLF TRAP WOLF DOUBLE
BACK BEAM
WOLF HIGH CASTLE TRAY
WARPING
BOARD
OIL BOTTLELOOM BENCH
FIGURE 5
G