Schaerer Ambiente 2 User manual

M.Schaerer Ltd. Phone: [phone] User manual
Gewerbestrasse 15 Fax: [phone] BASO 2 - 02
3302 Moosseedorf E-Mail: [email protected]
Switzerland Internet: www.schaerer.com Order number: 020'201

Introduction
BASO-2 - 02.00 - V07 Page 0-1
User Manual for
Coffee Machines
Published by: M. Schaerer AG
CH-3302 Moosseedorf
Version: Version 07 / October 2001
Software: NT 2000 V 1.05
Designed and edited by: M. Schaerer AG, CH-3302 Moosseedorf
© Copyright by M. Schaerer AG, CH-3302 Moosseedorf
All rights reserved, including translation into other languages. This manual may not be
copied, photocopied or distributed, in whole or in part, by any means, nor transmitted
electronically, without the publisher’s written consent.
All the information, technical data and illustrations in this instruction manual are based
on the latest data available at the time of going to press. M. Schaerer AG reserves the
right to undertake modifications at any time without further notice.

Introduction
Page 0-2 BASO-2 - 02.00 - V07

Introduction
BASO-2 - 02.00 - V07 Page 0-3
0. SAFETY INSTRUCTIONS AND WARNINGS
Read the information in the user manual carefully be-
fore using the machine for the first time. It contains
important information on safety, use and service of
the machine.
0.1. Safety
This chapter contains important safety information and liability provisions
on how to avoid damaging the machine, outlined in this instruction man-
ual. You will also find instructions for conventional use.
This chapter warns you about possible dangers by conventional use of
the machine. The information on how to recognize danger enables a safe
and correct operation.
It is absolutely crucial to read and understand this chapter before
using the machine.
0.2. For your safety
Please keep this operating manual in the vicinity of the machine.
The machine will be handed over by the authorized after sales service
organization. Please familiarize yourself with the operating manual before
you use the machine for the first time. It is crucial that you read the safety
notes. Especially important points are marked with a symbol.
Dangers by maloperation or misuse,
•for the operators body and life and for third persons and animals that
are in the vicinity of the machine.
•for the machine and other valuables belonging to the operator and
third persons.
•that the machine will not run smoothly.

Introduction
Page 0-4 BASO-2 - 02.00 - V07
0.2.1. Safety symbols used in these instructions
The following symbols occur in conjunction with all important notes on
safety in these operating instructions. Follow the instructions to the letter
and proceed with particular care in such cases.
•Identification of notes on safety:
Danger!
This note indicates a risk of severe and/or fatal injury if specific proce-
dural rules are violated.
Please take all necessary safety precautions if you see this symbol in the
operating instructions.
Danger!
Danger of electric shock!
Attention!
This note warns you of damage to property as well as of financial and
statutory penalties (e.g. loss of rights to claim under guarantee, liability
suits, etc.).
Environmental protection!
Check the equipment you are using is environmentally friendly.
Comply with the disposal regulations of the country you are in and take
advantage of the local opportunities provided for correct waste disposal.
Bear in mind that environmental protection is to everyone’s benefit.
Note:
This provides important notes and information.

Introduction
BASO-2 - 02.00 - V07 Page 0-5
0.3. Liability Claims under guarantee and liability claims in the event of injury to peo-
ple and damage to property cannot be entertained if they are due to one
or more of the following causes:
–Unconventional use of the machine
–Improper assembling, start-up, operation and service of the machine
–Operating the machine with defect safety devices or when safety de-
vices are not in place or functioning properly
–Failure to comply with the information in the operating manual re-
garding storage, assembly, start-up, use and service of the machine
–Inadequate monitoring of worn parts
–Incorrectly undertaken repairs
–Catastrophic damage due to the influence of foreign bodies, acci-
dents, vandalism and force majeure
Attention!
The machine must be serviced by an after sales service organization au-
thorized by the manufacturer. The service interval is every 12 months or
after 45,000 servings of coffee.
The manufacturer accepts claims on the guarantee and/or any liability
only and exclusively providing the specified service intervals have been
observed. The guarantee only applies if any spare parts used have been
ordered from the manufacturer or from a supplier authorized by the
manufacturer.
Safety-relevant parts, such as safety valves, boiler, etc., must be re-
placed and are not allowed to be repaired.
For safety reasons the safety valve must be replaced every 12
months. The steam generator and instant heater must be replaced
every 36 months for safety reasons.

Introduction
Page 0-6 BASO-2 - 02.00 - V07
0.4. Accident prevention regulations
0.4.1. General
Note:
This chapter describes the safety instructions and accident prevention
regulations, which you must adhere to for your own safety and the safety
of others.
Before each start-up of the machine:
- Check its operational safety! Carefully perform the checks as de-
scribed in the individual chapters.
- Abide by the instructions, the safety and accident prevention regula-
tions in this user manual as well as your local legal technical safety
and hygiene regulations.
- Immediately rectify any malfunctions, which impair safety.
0.4.2. Unauthorized users
Danger!
Persons who are unfamiliar with the operating manual, children as well
as persons under the influence of drugs or medication must not operate
the cold milk solution machine unless supervised. In a self-serve
establishment, the operator must mark the machines in the beverage and
heat retaining plate area in such a way that the customers easily can see
it’s a danger zone.
0.4.3. Malfunctions
Attention!
Be sure that only authorized and trained personnel work on the machine!
The provisions of the local employers’ liability insurance association or
other responsible supervisory bodies must be adhered to in all cases!
If malfunctions occur, they must only ever be rectified by trained and au-
thorized specialists!
0.4.4. Electrical energy
Danger!
Work on electrical systems is only allowed to be undertaken by an elec-
trician or by trained personnel under the supervision of an electrician and
in accordance with the rules governing electrical engineering work. The
appropriate EU directives on low voltage and/or the country’s or local
safety rules and regulations are in effect.
Danger!
Never touch live parts! Connect only the machine to AC. The voltage
must correspond to the value given on the rating plate of the machine. It
is strictly forbidden to insert any object into the machine or to open up the
housing!
Before servicing, always turn off the main switch to the machine or take
the mains plug out of the socket.
Otherwise there is a danger of electric shock!

Introduction
BASO-2 - 02.00 - V07 Page 0-7
0.4.5. Equipment
Attention!
If any parts of the unit are leaking or if any cables, hoses, screw connec-
tions, flanges, valves, seals, etc. have external signs of damage then this
must immediately be reported to the authorized specialist staff and recti-
fied by them!
0.4.6. Environmental protection regulations
Environmental protection!
When selecting cleaning agents, make sure that they are environmentally
safe, bear no health risks, and comply with the local disposal regulations.
Use the cleaning agents recommended by the manufacturer.
0.4.7. Designated use
The designated use of the coffee machine and the options connected
with it are subject only to the contractually agreed mode of use and any
existing supplementary agreements, the “general business conditions“ of
M. Schaerer AG and this user manual..Any use other than within the lim-
its specified here shall be regarded as not in accordance with the desig-
nated use. The manufacturer shall not be liable for any damage resulting
from this.
Adherence to the servicing and maintenance intervals stipulated by the
manufacturer.

Introduction
Page 0-8 BASO-2 - 02.00 - V07
0.4.8. Technical condition
The machine must only be operated as designated, if technically safe
and if you are fully aware of the safety and danger and follow the appro-
priate regulations.
If any malfunctions are detected, particularly such which could impair
safety, they must immediately be rectified by the appropriate personnel.
0.4.9. Cleaning agent
When using a cleaning agent, please refer to the notes and specifications
on the cleaning container’s label and the specifications and safety data
sheet mentioned in chapter 5 “Cleaning” and chapter 9 “Appendix”.
0.5. Safety notes and rating plates
Attention!
True safety means being familiar with all the notes on safety. This relates
to the nature and location of the hazard and in particular to the safety
measures taken to counteract it. Always remain on the alert and be
aware of the danger(s).
The machine is supplied with rating plates. Please keep these in read-
able condition.