Schlage PG1000 User manual

PG1000
USB Proximity Desktop Reader and Programmer
User Guide

Contents
2
Contents
Requirements and Specifications ......................................................................................................................... 3
Items needed (Included in the box): ................................................................................................................... 3
Computer Requirements .................................................................................................................................... 3
Minimum ....................................................................................................................................................... 3
Recommended ............................................................................................................................................. 3
Technical Specifications ..................................................................................................................................... 3
Installation Procedure ............................................................................................................................................ 4
Installing the Software: ....................................................................................................................................... 4
Installing the Hardware: ...................................................................................................................................... 4
Operation ................................................................................................................................................................. 5
Default ................................................................................................................................................................ 5
Reader Mode ...................................................................................................................................................... 5
Programmer Mode .............................................................................................................................................. 6
Troubleshooting ...................................................................................................................................................... 7
Disclaimers and Warranty ...................................................................................................................................... 7
FCC Compliance ..................................................................................................................................................... 7
Contact Information ................................................................................................................................................ 7

Requirements and Specifications
3
Requirements and Specications
Items needed (Included in the box):
1. Schlage Desktop Proximity Programmer and Credential Reader
2. Host A to Device mini-B USB Cable
3. Compact Disc containing the software user interface and this user manual
4. Quick Start Guide
Computer Requirements
Minimum
1.0 GHz Processor, 256MB RAM, DirectX 7 level graphics card, 10MB Hard Disk Space Available, Windows XP/Vista/7,
Microsoft .Net Framework 3.5 SP1 or higher, Mouse, Keyboard
Recommended
1.8 GHz Processor, 512MB RAM, DirectX 9 level graphics card, 10MB Hard Disk Space Available, Windows XP/Vista/7,
Microsoft .Net Framework 3.5 SP1 or higher, Mouse, Keyboard
Technical Specications
Frequency 125 kHz
Standard Default Configuration Proximity Card Reader
Certifications FCC Certification
Canadian Certification
CE Mark
Voltage Range 4.75V to 5.25V
Power Supply USB Bus powered
Max. Current Requirement 190 mA
Average Current Requirement 125 mA
Cable Specification 10’ USB 2.0 Cable
(Type A to Type Mini B)
System Interfaces USB Mini-B
Operating Temperature 32 to 100 F (0 to 38 C)
Physical Dimensions (HWD) 4” x 4” x 3/4”
(10.16cm x 10.16cm x 1.91 cm)
Weight 4.2 oz. (120 grams)
Material PBT Polymer
Color Black
Maximum Read Range up to 6” (15.24cm)

Installation Procedure
4
Installation Procedure
The order of installation does not matter, though installing the Software first is recommended.
Installing the Software:
1. Place the installation CD in the CD-ROM drive.
2. The disk should auto-play.
If the disc does not auto-play:
a. Navigate to the CD-ROM drive through Windows Explorer.
b. Double-click Setup.exe.
3. Follow the on-screen instructions to complete the software installation.
ÎÎYouÎmayÎbeÎrequiredÎtoÎdownloadÎtheÎ.Net FrameworkÎ3.5ÎSP1ÎorÎhigherÎfromÎMicrosoftÎtoÎstartÎinstallation
Installing the Hardware:
1. Plug the mini-B side of the USB cable into the Desktop Reader/
Programmer.
2. Plug the A side of the USB cable into the USB port on the host
computer.
3. The hardware will complete a self-installation.

Operation
5
Operation
Default
After the Desktop Reader/Programmer has been plugged into the host computer, it will function as a desktop reader. In
this mode the device behaves much like a keyboard. If a user presents a credential before setting the decoding options,
the device will print the binary information of the card into the active window or data field if it receives text. The number of
characters that appear represent the card format (e.g. if 26 characters appear, you have presented a 26 bit card).
While in Default mode, the LEDs will be solid red. When a credential is presented and successfully read, the LEDs will
change from red to green then back to red and the device will beep. If the credential was not successfully read, the LEDs
will not change color and the device will not beep.
If a credential is presented that is initialized by XceedID but not programmed, the LED will alternately flash red and amber
as long as the credential is in the field.
Reader Mode
To get the device out of default mode and into reader mode the user must select the following then click the “Configure
Device” button.
• Card Format
• Data Return Type
• Data Format
• Prefix
• Suffix
Once configured, the device will return the values read from the presented credential. The default behavior is to output
this data to the Output textbox on the Reader interface. If the user chooses to have the information output to another area,
as in default mode, the user must simply click in an area that accepts text (e.g. a text or worksheet file) then present the
card to the reader.
While in Reader Mode, the LEDs will be solid red. When a credential is presented and successfully read, the LEDs will
change from red to green then back to red and the sensor will beep. If the credential was not successfully read, the LEDs
will not change color and the sensor will not beep.
If a credential is presented that is initialized by XceedID but not programmed, the LED will alternately flash red and amber
as long as the credential is in the field.

Operation
6
Programmer Mode
To get the device into Programmer Mode, the user must click the programmer tab at the top of the application window.
This will change the window to allow the user to program a card or multiple cards.
The user must then specify all of the following options then click the program button.
• Card Format
• Facility Code
• City Code (only in select formats)
• Badge ID
• Number to Program (1 is default)
While in programmer mode, the LED will be solid amber. To program the card, simply present the card to the device after
clicking the Program button. A successful card program will be indicated by the LED flashing green once and two beeps.
If more cards are to be programmed, the LED will revert back to solid amber and the badge ID will increment plus one. If
there was only one card to program or the final card was programmed, the LED will flash green and there will be 7 short
beeps.
ÎÎWhenÎprogrammingÎmultipleÎcardsÎtheÎLEDsÎgoÎAmberÎ(waiting)Î->ÎGreenÎ(SuccessfulÎprogram)Î->ÎRedÎ(veryÎ
quickly)Î->ÎAmberÎ(waitingÎonÎcredential)
ÎÎTheÎdeviceÎwillÎonlyÎprogramÎXceedIDÎProximityÎcredentials

Troubleshooting
7
Troubleshooting
Problem Solution Solution
Device is not recognized by my
computer
Unplug device from PC and plug it
back in
Unplug device from USB port and plug
into a different USB port
Device not programming cards Verify that the device is in programmer
mode the LED indicator should be
AMBER.
Verify cards are XceedID Proximity
credentials (Device will not program
other vendors credentials)
Device has hung and is non-
responsive
Reset the device by unplugging the
USB cable and plugging it back in, the
SW Interface will need to closed and
restarted as well.
The pause button has been hit but
the device appears to be in stuck in
programmer mode
Device has received a program
command already; it will program 1
more card after hitting pause before it
actually pauses.
Disclaimers and Warranty
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Warranty: Limited lifetime against defective workmanship and materials
FCC Compliance
The FCC requires the following statement: This device uses radio frequency energy and has been tested and complies
with the limits of FCC testing. Changes, modifications, or disregard of proper instillation and instructions not expressly
approved by XceedID, and is strictly prohibited by the FCC and could void the user’s authority to operate this equipment.
Contact Information
XceedID Corporation
500 Golden Ridge Road
Building 1, Suite 160
Golden, CO 80401
Phone: [phone]
Fax: [phone]
http://www.xceedid.com/

©2010 Schlage Lock Company
23735699 Rev. 10/10-a