Schmidt PT-100 User manual

Tension Meter
PT Series
Model PT-100
PT-100-L
Edition PT 01.0.E
Operating Instructions
Valid as of: 15.04.2011 • Please keep the manual for future reference!
S C H M I D T
c o n t r o l i n s t r u m e n t s

2
Contents
1 Warranty and Liability..............................................................................................3
1.1 Notices within the Operating Instructions...............................................................3
1.2 Responsibilities of the Operating Company...........................................................3
1.3 Responsibilities of the Personnel...........................................................................3
1.4 Informal Safety Measures......................................................................................4
1.5 Training of the Personnel.......................................................................................4
1.6 Intended Use..........................................................................................................4
1.7 Dangers in Handling the Device.............................................................................4
1.8 Copyright................................................................................................................4
1.9 Declaration of Conformity, RoHs II and WEEE Registration..................................4
2 Available Models.......................................................................................................5
2.1 Specifications.........................................................................................................5
2.2 Delivery Includes....................................................................................................5
2.3 Unpacking..............................................................................................................6
3 Initial Setup and Operating Procedure...................................................................6
3.1 Notes Before Starting Measurement......................................................................6
3.2 Operating Elements ...............................................................................................6
3.3 Setup......................................................................................................................7
3.3.1 Charging the Battery.........................................................................................7
3.3.2 Switch-On.........................................................................................................7
3.3.3 Switch-Off.........................................................................................................7
3.3.4 Selecting the Units of Measure.........................................................................8
3.3.5 Zero Adjustment of the Measuring Position (Auto Zero) ..................................8
3.3.6 Selecting the Operating Mode..........................................................................9
3.4 Taking a Measurement ..........................................................................................9
3.4.1 Measuring in Tension Mode.............................................................................9
3.4.2 Measuring in Speed Mode..............................................................................10
3.4.3 Measuring in Length Mode.............................................................................10
3.4.4 Displaying the Average...................................................................................12
3.4.5 Activating Damping Mode...............................................................................13
3.4.6 Changing the Damping Factor........................................................................13
3.5 Error Messages....................................................................................................14
3.6 Dynamic Verification of Measuring Accuracy.......................................................14
3.7 Static Verification of Measuring Accuracy............................................................15
4 Service and Maintenance.......................................................................................15
4.1 Rollers..................................................................................................................15
5 Cleaning...................................................................................................................15
6 Verification Intervals ..............................................................................................16
7 Correspondence.....................................................................................................16
8 Repairs.....................................................................................................................16

3
All persons who work with the device agree to perform the following duties before starting
work:
- to observe the basic regulations on industrial safety and accident prevention.
- to read the chapter on safety and the warning notices in these Operating Instructions and
to confirm with their signatures that they have understood them.
1 Warranty and Liability
In principle, the supply of the device is subject to our “General Conditions of Sale and
Delivery.” These have been provided to the operating company on conclusion of the
contract, at the latest.
Warranty:
- SCHMIDT tension meters are warranted for 12 months.
Parts subject to wear, electronic components and measuring springs are not covered by
the warranty. No warranty or liability will be accepted for bodily injury or property damage
resulting from one or several of the following causes:
- Misuse or abuse of the device.
- Improper mounting, commissioning, operation and maintenance of the device
(e.g. verification interval).
- Operation of the device if any safeguards are defective or if any safety and protection
precautions are not properly installed or not operative.
- Failure to comply with the notices in the Operating Instructions regarding transport,
storage, mounting, commissioning, operation, maintenance and setup of the device.
- Any unauthorized structural alteration of the device.
- Insufficient inspection of device components that are subject to wear.
- Opening the device or improper repair work.
- Disasters caused by the effects of foreign objects or by force majeure.
1.1 Notices within the Operating Instructions
The fundamental prerequisite for the safe handling of this device and its troublefree opera-
tion is the knowledge of the basic safety notices and safety instructions.
These Operating Instructions contain the most important notices for the safe operation of
the device.
These Operating Instructions, in particular the safety notices, must be observed by any
person who works with the device. In addition, the locally valid rules and regulations for
the prevention of accidents must be complied with.
The representations within the Operating Instructions are not true to scale.
The dimensions given are not binding.
General indications of direction, such as FRONT, REAR, RIGHT, LEFT apply when view-
ing the front of the device.
1.2 Responsibilities of the Operating Company
In compliance with the EC Directive 89/655/EEC, the operating company agrees to only
permit persons to work with the device who:
- are familiar with the basic regulations on industrial safety and accident prevention and
who have been trained in handling the device.
- have read and understood the chapter on safety and the warning notices in these
Operating Instructions and have confirmed this with their signatures.
- are examined regularly on their safe and conscientious working method.
1.3 Responsibilities of the Personnel

4
The device was designed according to the state of the art and the approved safety stan-
dards. Nevertheless, its use may cause serious or fatal injury to the user or third persons,
and/or an impairment of the device or of other material assets.
The device may only be applied:
- For its intended use in a faultless condition with regard to the safety requirements.
- Malfunctions that could impair safety must be remedied immediately.
- Personal protective equipment must be used according to the EC Directive 89/686/EEC.
The Operating Instructions must always be kept on hand where the device is operated.
Apart from the Operating Instructions, the generally and locally valid regulations on acci-
dent prevention and environmental protection must be provided and complied with.
1.4 Informal Safety Measures
1.6 Intended Use
1.7 Dangers in Handling the Device
The device is intended exclusively to be used for measuring tension, yarn speed and yarn
length. Any other use or any use exceeding this intention will be regarded as misuse. Un-
der no circumstances shall HANS SCHMIDT & Co GmbH be held liable for damage result-
ing from misuse.
The intended use also includes:
- Complying with all notices included in the Operating Instructions and observing all
inspection and maintenance works.
1.8 Copyright
1.9 Declaration of Conformity, RoHs II and WEEE Registration
In compliance with the EU Directives 2004/108/EG and 2011/65/EU
HANS SCHMIDT & CO GmbH is registered in compliance with
the German Electrical and Electronic Equipment Act (ElektroG)
under WEEE Reg. No. DE 48092317.
The copyright on these Operating Instructions remains with the company
HANS SCHMIDT & Co GmbH.
These Operating Instructions are intended for the operating company and its personnel
only. They contain instructions and notices that may only be reproduced on the prior writ-
ten permission of
HANS SCHMIDT & Co GmbH
and under indication of the complete reference data.
Violations will be prosecuted.
1.5 Training of the Personnel
Only trained and instructed personnel is permitted to work with the device. The responsi-
bilities of the personnel must be clearly defined for mounting, commissioning, operation,
setup, maintenance, and repair. Trainees may only work with the device under the super-
vision of experienced personnel.
The device must not be operated in potentially explosive areas
and must not come into contact with aggressive substances.

5
2 Available Models
* Suitable for 95% of all applications. PA = Polyamide Monofilament.
International unit of tensile force: 1 cN = 1.02 g = 0.01 N
Model Measuring Range
Tension Measuring Range Speed Measuring Range Length
*SCHMIDT
Calibration
Material
PT-100 0.5 - 100.0 cN
0.5 - 100.0 g PA: 0.20 mm Ø
PT-100-L 0.5 - 100.0 cN
0.5 - 100.0 g 0 - 1999 m/min 0 - 1999 in/min 0 - 1999 m 0 - 1999 in PA: 0.20 mm Ø
These Operating Instructions refer to model PT-100 and PT-100-L of the PT Series.
2.1 Specifications
Calibration: According to SCHMIDT factory procedure
Accuracy: ± 1.5 % FS* ± 1 digit
Length measuring: 0.5 % and ± 1 digit
Measuring Units: cN, grs available
m, in, m/min, in/min (only PT-100-L)
Overload Protection: 200 % FS*
Measuring Principle: Strain gauge bridge
Damping: Selectable electronic damping (moving averaging)
Display Update Rate: 2 times per sec.
Display: 3 ½ digit LCD, 9 mm high
Power Supply: LiPo accumulator (40 h continouse use, 3.5 charging time)
and AC adapter 110 - 240 V AC with country-specific
adapters (EU/USA/UK)
Auto Power Off: Automatically after approx. 3 min. of non-use
Temperature Range: 10 - 45° C
Air Humidity: 85 % RH, max.
Housing Material: Aluminium
Dimensions: 141 mm x 36 mm x 22 mm (L x W x H)
Weight net (gross): Approx. 170 g (approx. 500 g)
*FS = Full Scale
Guide Rollers:
V-grooved Line Speed
max. m/min Roller Material
Standard 2000 Aluminium hardcoated
2.2 Delivery Includes
1Tension meter
1AC-adapter with 3 country-specific adapters (EU/USA/UK)
1 Certificate of compliance with the order 2.1 under EN 10204
1Sensor (only PT-100-L)
1Magnet (only PT-100-L)
1Operating Instruction
1Carrying case

6
3 Initial Setup and Operating Procedure
3.1 Notes Before Starting Measurement
Have you read and understood the Operating Instructions, in particular
Chapter 1 “Basic Safety Notices” ?
You are not permitted to operate the tension meter before doing so.
Before working with the instrument you must put on your personal protective
clothing, if necessary. For example, eye protectors, gloves, etc.
To avoid damage, do not move the rollers by hand.
Tensions that exceed the tension range of the instrument by more than 100%
may cause permanent damage to the measuring spring and must be avoided
under any circumstances.
2.3 Unpacking
Unpack the tension meter and inspect it for any shipping damage.
Notices of defect must be filed immediately, at the latest within 10 days on receipt of the
goods.
3.2 Operating Elements
fig. 3.1 Calibration label
(option)
SCHMIDT-Quality Seal
ID plate with serial number
1
2 3 4 5
fig. 3.2
1 MEASURING ROLLER (tension / length / speed)
2 MEASURING ROLLER (tension)
3 DISPLAY
4 ON / OFF / ZERO key
5 DAMP (damping) / START / STOP key
6 USB Port
6
The ID plate with CE mark and serial number is provided on the bottom of the
tension meter; the calibration label (optional) and the SCHMIDT Quality Seal are
provided on the side.

7
3.3 Setup
The tension meter comes with a built-in rechargeable LiPo battery, which has been
charged at the factory. The tension meter can only be switched on if the battery is still
working, i.e. if the battery has enough charge. If the instrument does not power up or if
the battery level indicator shows only one bar after power-up (Chapter 3.3.2), the
battery needs to be recharged.
To ensure maximum battery life, avoid discharging it completely
or charging it frequently for short periods.
The battery should not be stored for a prolonged time when empty.
After a maximum storage period of one year, the battery has to be recharged.
3.3.1 Charging the Battery
The battery can only be charged at a temperature between +5 °C
and +45 °C.
Before you connect the AC adapter, verify that the supply voltage is correct
(100 V - 240 V).
HANS SCHMIDT & Co. GmbH provides no warranty or liability for any
damage resulting from the use of AC adapters from other manufacturers.
To charge the battery, connect the cable of the AC adapter to the USB port.
When the battery is fully charged, the battery level indicator will show 3 bars .
The charging time is approx. 3.5 hours.
Battery overcharging is not possible
3.3.2 Switch-On
- Press the ON/OFF key .
The DISPLAY then momentarily shows the tension range and the software version,
e.g. E 1.0.
- After that the DISPLAY shows
- The instrument subsequently carries out a self test and the zero adjustment (see also
Chapter 3.3.5)
The DISPLAY shows , the tension meter is now ready to operate.
3.3.3 Switch-Off
Auto power off:
- The tension meter switches off automatically after 3 minutes of non-use.
Manual switch-off:
- Press the ON/OFF key for about 7 seconds.

8
3.3.5 Zero Adjustment of the Measuring Position (Auto Zero)
Zero adjustment is automatically carried out for the current measuring position.
Zero adjustment must be carried out whenever the tension meter does not
display “0” in measuring position.
The process material must not yet be inserted!
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
To carry out zero adjustment:
- Hold the tension meter in the desired measuring position. Be careful to hold the
instrument absolutely steady.
- Press the ON/OFF/ZERO key.
The DISPLAY momentarily shows and then switches to .
The tension meter is now adjusted for the new material path and is ready to measure.
3.3.4 Selecting the Units of Measure
You can set the instrument to cN or g for tension measurements and to m or inch
for length measurements. The default settings are cN and m.
Requirement:
Tension meter switched off as described in Chapter 3.3.3.
- Press and hold the ON/OFF key until the display shows the currently selected
units of measure .
- Release the ON/OFF key and then press the DAMP key to select the units of
measure you want to use for your tension, length and speed
measurements.
- Press ON/OFF to save the selected units of measure.
The unit for speed measurements results from the unit selected for length
measurements.
Reading on
display Unit of measure Tension mode Unit of measure Length mode Unit of measure Speed mode
centinewton (cN) meter (m) meters per minute (m/min)
centinewton (cN) inch (in) inches per minute (in/min)
gram (grs) meter (m) meters per minute (m/min)
gram (grs) inch (in) inches per minute (in/min)

9
3.3.6 Selecting the Operating Mode
The following operating modes are available:
• Tension mode (F) - PT-100 and PT-100-L
• Length mode (L) - PT-100-L only
• Speed mode (S) - PT-100-L only
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
After power-up, the instrument is in tension mode (F) by default.
You can cycle through the operating modes by simultaneously pressing the DAMP and
ON/OFF keys.
Tension mode: The display briefly shows and then .
Press DAMP and ON/OFF.
Length mode: The display briefly shows and then .
Press DAMP and ON/OFF.
Speed mode: The display briefly shows and then .
The last operating mode used is not stored in memory when you turn off the in-
strument. After power-up, the tension mode is always active by default.
3.4 Taking a Measurement
3.4.1 Measuring in Tension Mode
Requirements:
Switch on the tension meter (Ch. 3.3.2), carry out zero adjustment if required (Ch. 3.3.5),
change the damping factor if necessary (Ch. 3.4.6), and select the tension mode
(Ch. 3.3.6) and the required unit of measure (Ch. 3.3.4).
fig. 3.4.1a
fig. 3.4.1b

10
3.4.1 Measuring in Tension Mode (Cont.)
To insert the process material:
- Place the PROCESS MATERIAL between the two rollers (fig. 3.4.1a).
- Rotate the tension meter by approx. 180 degrees (fig. 3.4.1b).
It is important to assure that the PROCESS MATERIAL runs smoothly
over the ROLLERS.
To measure the process material:
The DISPLAY now shows the measured tension values.
Error messages which might be displayed are described in Chapter 3.5.
Damping:
If tension fluctuates, the damping feature should be enabled as described in Chapter
3.4.5 or the damping factor should be adjusted as described in Chapter 3.4.6.
To remove the process material:
- Rotate the tension meter by 180 degrees.
- Remove the PROCESS MATERIAL.
3.4.2 Measuring in Speed Mode
Requirements:
Switch on the tension meter (Ch. 3.3.2) and select the speed mode
(Ch. 3.3.6).
- Insert the PROCESS MATERIAL as described in Chapter 3.4.1.
- Press the ON/OFF/ZERO key.
- The DISPLAY now shows the measured values.
3.4.3 Measuring in Length Mode
While a length measurement is active, “:” blinks on the display.
Continuous measurement
The measurement is performed for as long as PROCESS MATERIAL is run over the roll-
ers.
Requirements:
Switch on the instrument (Ch. 3.3.2) and select the length mode (Ch. 3.3.6) and the unit
of measure (Ch. 3.3.4).
1.Press and hold the ON/OFF key.
The length mode settings are indicated on the display.
2.Press the DAMP key until the display shows .
3.Insert the PROCESS MATERIAL as described in Chapter 3.4.1.
This activates the length measurement.
4.Press the ON/OFF/ZERO key to zero the display and start a new measurement.
The previous reading is not saved.
5.The measurement stops when you remove the PROCESS MATERIAL as described in
Chapter 3.4.1.

11
3.4.3 Measuring in Length Mode (Cont.)
Measuring with manual start / stop signal
The measurement is performed for a user-defined time.
Requirements:
Switch on the instrument (Ch. 3.3.2) and select the length mode (Ch. 3.3.6) and the unit
of measure (Ch. 3.3.4).
1.Press and hold the ON/OFF key.
The length mode settings are indicated on the display.
2.Press the START/STOP key until the display shows .
3.Insert the PROCESS MATERIAL as described in Chapter 3.4.1.
4.Then press the START/STOP key to start the length measurement.
5.When you want to stop measuring, press the START/STOP key once again. The
measured value is displayed.
4.To zero the display, press the ON/OFF/ZERO key. You can then start a
new measurement. The previous reading is not saved.
To perform measurements using a manual start/stop signal, make sure that
no sensor signal is transmitted to the instrument. For this purpose, remove
the magnet from the machine or disconnect the sensor from the instrument.
Measuring with automatic start / stop signal
The measurement is performed for a user-defined number of machine revolutions.
fig. 3.4.2a
MAGNETIC SWITCH
MAGNET
Recommended switching distance approx. 2 mm
M5 thread
CYLINDER of CIRCULAR
KNITTING MACHINE
The model PT-100-L features an adjustable counter for up to 10 cylinder
revolutions of the knitting machine. The cylinder revolutions are monitored by a
magnetic switch.
To use this feature, the SUPPLIED MAGNET must be mounted to the cylinder of the
knitting machine by using an M5 flat head bolt. The supplied MAGNETIC SWITCH is
fitted to the stationary part of the knitting machine so that it is at the same height as the
SUPPLIED MAGNET (see fig. 3.4.2b). The switching distance between the SUPPLIED
MAGNET and MAGNETIC SWITCH should be set to about 2 mm with the adjusting nut
and lock nut of the MAGNETIC SWITCH.

12
Mounting example:
Flat head bolt (M5)
Recommended switching distance approx. 2 mm
fig. 3.4.2b
MAGNET
MAGNETIC SWITCH
ADJUSTING NUT
LOCK NUT
ANGLE BRACKET
(not included)
CYLINDER of CIRCULAR
KNITTING MACHINE
1.Press and hold the ON/OFF key.
The length mode settings are indicated on the display.
2.Press the DAMP key to set the desired number of machine revolutions
(e.g. 3 revolutions).
3.Insert the PROCESS MATERIAL as described in Chapter 3.4.1 and press the ON/
OFF/ZERO key.
4. On receiving the first switching pulse from the magnetic switch, the instrument
starts counting the defined number of revolutions, starting from zero.
The first switching pulse from the MAGNETIC SWITCH also triggers the
measurement and display of the filament length.
5. After the defined number of revolutions, the instrument stops measuring the
filament length.
The DISPLAY shows the measured filament length.
To start a new measurement, zero the display by pressing the
ON/OFF/ZERO key. The previous reading is not saved.
3.4.4 Displaying the Average
In the tension and speed modes, you can display the average of the last
measurement process as soon as you stop the measurement.
Requirement:
The process material has to be removed on completion of the measurement.
- Press the ON/OFF key to display the average.
After you display the average or turn off the instrument, the average cannot be
displayed again.
3.4.3 Measuring in Length Mode (Cont.)

13
3.4.5 Activating Damping Mode
Damping can only be activated and changed in the tension
mode.
The tension meter is equipped with an electronic damping which ensures steady read-
ings when tension fluctuates. This is achieved by averaging the measured values at the
set update rate. Before switching on the damping mode, it is recommended that you
measure the first values without damping enabled.
Requirements:
- Process material inserted as described in Chapter 3.4.1.
- The DISPLAY has shown the first tension values.
To switch on damping:
- Press the DAMP key.
The display shows the set damping factor e. g. .
- Release the DAMP key.
The DISPLAY shows
2 2 1.
Damp
cN
DAMP below the currently measured value.
To switch off damping:
- Press the DAMP key.
The DISPLAY shows
12
cN
only the currently measured value.
3.4.6 Changing the Damping Factor
The tension meter is factory preset to a factor of 06. The tension values are thereby
averaged for the display in the following way:
6 old values + 4 new values
10
The damping factor can be modified in 15 steps from 01 = low damping:
1 old value + 9 new values
10
to 15 = high damping:
9 old values + 1 new value
10
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
Procedure:
- Press and hold the DAMP key.
The display shows the currently selected damping factor.
- You can now change the damping factor with the OFF/ON key.
- Release the DAMP key.
The tension meter returns to the measuring mode.

14
3.5 Error Messages
Error message 1:
- The DISPLAY shows
EEE
.
The upper limit of the measuring range was exceeded by more than 100%.
Reduce the applied load.
OR
AUTO ZERO is no longer possible.
Return the tension meter to the manufacturer for factory calibration.
Error message 2:
- The DISPLAY shows .
The lower limit of the measuring range was fallen below by more than 100%.
Properly insert the process material.
OR
AUTO ZERO is no longer possible.
Return the tension meter to the manufacturer for factory calibration.
3.6 Dynamic Verification of Measuring Accuracy
All tension meters are calibrated with standard materials - such as polyamide monofila-
ment (PA) - according to the SCHMIDT factory procedure. The diameters are given in
Chapter 2. Any difference in process material size and rigidity from the standard material
may cause a deviation of the accuracy.In 95% of all industrial applications, the SCHMIDT
calibration has been proven to provide the best results and is used for comparative pur-
poses.The tension meter is factory calibrated for a vertical material path (fig. 3.7).
The tension meter has been calibrated dynamically according to the
SCHMIDT factory procedure.
Therefore, differences may occur between static and dynamic readings.
fig. 3.6
Line speed Vmax. = 100 m/min
Hang twice the weight (pulley effect) which corresponds to the
tension to be measured from the measured material, vertically,
as shown here. Please keep in mind to include the weight of
the lower deflection pulley when you calculate the suspended
weight. Pay attention to the correct unit of measure cN.

15
3.7 Static Verification of Measuring Accuracy
All tension meters are calibrated with standard
materials - such as polyamide monofilament (PA) -
according to the SCHMIDT factory procedure. The
diameters are given in Chapter 2. Any difference in
process material size and rigidity from the standard
material may cause a deviation of the accuracy.
In 95% of all industrial applications, the SCHMIDT
calibration has been proven to provide the best
results and is used for comparative purposes.The
tension meter is factory calibrated for a vertical
material path (fig. 3.6).
Requirement:
The required reference weight must be available.
Verification procedure:
- Hang a WEIGHT which corresponds to the tension to be measured from the
PROCESS MATERIAL, vertically, as shown in fig. 3.7.
Pay attention to the correct unit of measure.
- Insert the PROCESS MATERIAL as described in Chapter 3.4.1.
- The tension value shown on the DISPLAY should be equal to the value of the
suspended weight (pay attention to the measuring units).
If this procedure shows a deviation, the tension meter has to be returned to the manufac-
turer for factory calibration.
The tension meter cannot be calibrated by the user. Factory
calibration of the tension meter is essential.
4 Service and Maintenance
The tension meter is easy to maintain. Depending on operating time and load, the
tension meter should be checked according to the locally valid regulations and conditions
(as described in Chapter 3.6 and 3.7). The use of other test methods than the procedure
described in Chapter 3.6 and 3.7 may cause deviating measuring results.
4.1 Rollers
You should regularly inspect the rollers to assure that they are running easily and
smoothly. The rollers can only be changed by the manufacturer.
5 Cleaning
For cleaning the unit, do not use any
AGGRESSIVE SOLVENTS
such as trichloroethylene or similar chemicals.
NO WARRANTY OR LIABILITY
shall be accepted for damage resulting from improper cleaning.
fig. 3.7
MEASURING
ROLLS
WEIGHT
PROCESS
MATERIAL

6 Verification Intervals
The question of finding the right frequency of calibration accuracy verification depends
on several different factors:
Operating time and load of the SCHMIDT tension meter
Tolerance band defined by the customer
Changes of the tolerance band compared to previous verifications of calibration
Therefore, the interval between verifications must be determined by the user`s
Quality Assurance Department based on the user`s experience.
Assuming normal operating time and load as well as careful handling of the tension meter,
we recommend a verification interval of 1 year.
Should you have any questions regarding the instrument or Operating Instructions, or their
use, please indicate above all the following details which are given on the ID plate:
1) Model
2) Serial number
7 Correspondence
To avoid unnecessary follow-up questions, and the resulting loss of time or
possible misunderstandings, please return the instrument with a detailed fault
description to our service department. Please indicate in your order whether you
require an Inspection Certificate 3.1 according to DIN EN 10204.
8 Repairs
HANS SCHMIDT & Co GmbH
Schichtstr. 16
D-84478 Waldkraiburg
Germany
Service address:
Shipping instructions:
We kindly ask for return free of charge for us, if possible by airmail parcel. All occurring
charges, if any (such as freight, customs clearance, duty etc.), will be billed to customer.
For return from foreign countries, we ask you to include a proforma invoice with a low value
for customs clearance only, e.g. 50 Euro, each and to advise the shipment in advance by
fax or eMail.
Mailing address:
P. O. B. 1154
84464 Waldkraiburg Germany
Shipping address:
Schichtstr. 16
84478 Waldkraiburg Germany
Hans Schmidt & Co GmbH
Phone:
int. + 49 / (0)8638 / 9410-0
Fax:
int. + 49 / (0)8638 / 4825
int. + 49 / (0)8638 / 67898
More than 60 years - Worldwide -
e-mail:
[email protected]
Internet:
http://www.hans-schmidt.com