SCHUBERTH SRC?System User manual

U S E R M A N U A L
P O W E R E D B Y
QG SRC 207 - MAN00015 indd 21 2/1/11 11 38 AM

22
TABLE OF CONTENTS
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2. CONTENTS OF THE RETAIL BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3. CHARGING THE HEADSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4. BASIC SETUP AND CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.1 GENERAL FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.2 SPOKEN STATUS ANNOUNCEMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3 AUDIO SOURCES AND PRIORITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.4 SOFTWARE UPGRADE OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.5 RESETTING YOUR HEADSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5. GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.1 REPLACING THE EXISTING ACOUSTIC COLLAR WITH THE
SRC-SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.2 POSITIONING THE SPEAKERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.3 POSITIONING THE MICROPHONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.4 REMOVING THE SRC-SYSTEM FROM YOUR HELMET . . . . . . . . . . . . . . . . 27
5.5 WEARING AND REMOVING THE HELMET . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.6 CLEANING THE ACOUSTIC COLLAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6. CONNECTING BLUETOOTH® ENABLED MOBILE PHONES, GPS OR
MP3 (A2DP) DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.1 MOBILE PHONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.2 GPS DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.3 MP3 MUSIC WIRELESS OPTION  A2DP . . . . . . . . . . . . . . . . . . . . . . . . 29
7. BUILTIN FM RADIO AND EXTERNAL MP3 PLAYER CABLE OPTION . . . . . 30
7.1 FM RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.2 CABLE CONNECTING YOUR MP3 PLAYER OR OTHER
EXTERNAL AUDIO SOURCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8. USING THE MOBILE PHONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9. USING THE INTERCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.2 INTERCOM COMPATIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.3 BEFORE STARTING THE INTERCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.4 USING YOUR SRCSYSTEM FOR INTERCOM WITH OTHER
SRCSYSTEM HEADSETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.4a. TWOWAY INTERCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.4b. THREEWAY INTERCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.5 RECEIVING INTERCOM CALLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.6 INITIATE INTERCOM CALLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.7 VOICE CONNECT FEATURE VOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9.8 RESET PAIRING RESTORING THE ORIGINAL DEFAULT
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9.9 NOTEWORTHY ISSUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9.10 TROUBLESHOOTING THE INTERCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
10. CLICKTOLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11. SUPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12. NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
IMPORTANT: This is version 2.0 of the User Manual. Please note, that our
manual is updated periodically on our website in order to include the
very latest features as well the new options and functions of your new
SRC‑System. Please visit www.schuberth.com/leadmin/downloads/
SRC/SRC‑System_Manual‑1.pdf to check now if the manual you are
holding is the most updated version and download the website manual
version in your preferred language.
QG SRC 207 - MAN00015 indd 22 2/1/11 11 38 AM

English
23
1. INTRODUCTION
Congratulations and thank you for choosing the Schuberth Rider
Communication-System™ (SRC-System™) Headset for motorcycle
helmets.
This manual will help you operate the headset, but you should rst
familiarize yourself with the Bluetooth® functionality of your mobile
phone and/or GPS device before using the SRC-System™.
The SRC-System™ retail box contains one headset unit. When paired
with another SRC-System™, the headsets can be used as an Inter-
com at a range of up to 300 m/ 1,000 ft (subject to terrain).
YOUR SRCSYSTEM OFFERS THE FOLLOWING CONNECTIVITY
OPTIONS:
1. Mobile phone communication (supporting Bluetooth® Handsfree*
and A2DP and AVRCP proles at a 10 m / 33 ft. range)
2. Wireless music-streaming (supporting the Bluetooth® Stereo A2DP
prole and compatible with a variety of MP3 Players, adapters and
other audio devices)
3. 2-way or 3-Way Bike-to-Bike Intercom for conference calls with
other SRC-System™ headsets (up to 300 m / 1,000 ft) in Full
Duplex** mode.
4. Driver-to-Passenger Intercom
5. Click-to-Link for spontaneous intercom communication with any
nearby SRC-System™
6. GPS Navigation instructions and Streaming Audio from compatible
Bluetooth® devices
7. Built-in FM Radio
8. as a stereo headset for listening to cable-connected audio devices,
(such as non-Bluetooth® MP3 Players and iPods®)
ADDITIONAL SPECIAL FEATURES:
➤AGC technology (Automatic Gain Control), allowing your
SRC-System™ to automatically increase or reduce its volume
according to ambient noise and driving speed. You can also
control the volume level manually.
➤VOX technology for safe and handsfree operation of some key func-
tions (Voice Dial, answer call, reject call).
➤PLC software (Packet Loss Concealment) for real-time compensa-
tion of audio losses in challenging environments.
➤Advanced software which you should update while in standby
mode, via any PC running Windows® XP™, Vista™ or Windows 7™.
➤Spoken status instructions, so that you always know to whom or what
device you are connected to at any given time.
We wish you a great riding experience and remain available for any in-
quiries you may have. Just write us at [e-mail]
F-J. Görges Erwin Van Hoof
Director of Sales Vice President
SCHUBERTH GmbH Int. Sales Manager
Visit www.schuberth.com/src-tutorial/en to experience an interactive
demonstration of the SRC-System functions.
_______________________
* Mobile phones that do not support the Bluetooth® Handsfree prole may prevent
you from using certain advanced features
** “Full Duplex” lets you to speak and hear the other party simultaneously, similar to
mobile or landline phone conversations and unlike walkie-talkie communications
QG SRC 207 - MAN00015 indd 23 2/1/11 11 38 AM

24
2. CONTENTS OF THE RETAIL BOX
SRC-System™ for C3 helmets*
USB Connector
USB
Connector
Cover
2 Speakers
Pin Pin
Channel A Button
• Connect to Rider A
• Mp3 Button
Channel B Button
• Connect to Rider B
• FM Radio Button
Volume Up / Forward Button
Volume Down / Rewind Button
Flexible Boom Microphone
Mobile Phone
Button
SRC-System™ for C2 / Concept helmets
USB
Connector
2 Speakers
Pin
USB Connector
Cover
Pin Channel A Button
• Connect to Rider A
• MP3 Button
Channel B Button
• Connect to Rider B
• FM Radio Button
Volume Up / Forward
Button
Volume Down / Rewind
Button
Flexible
Boom
Microphone
Mobile Phone Button
*The product is
oered in
dierent sizes
Wall charger plug
USB adapter cable
Velcro® pads
MP3 cable
Microphone sponges
User Manual, stickers
IMPORTANT:
The cover lid protecting the micro USB Connector should be kept tightly
closed at all times to prevent moisture from entering the device.
3. CHARGING THE HEADSET
Make sure that your headset is fully charged for at least four
hours before initial use.
Insert the USB cable to the wall charger and
insert the other end of the cable to the
headset’s micro USB Connector. While charging,
the Red Light turns on. When charging is
complete, the Red Light will turn o.
Your wall charger and USB adaptor cable
serve two purposes:
1. Charging your headset from
any A/C wall socket or from a USB port on your computer
(charging time from computer takes longer)
2. Downloading software upgrades from any PC running
Windows® XP™, Vista™ or Windows 7™. (see section 4.4 for
details).
QG SRC 207 - MAN00015 indd 24 2/1/11 11 38 AM

English
25
4. BASIC SETUP AND CONFIGURATION
4.1 GENERAL FUNCTIONS
DESIRED RESULT REQUIRED ACTION
Turn on the headset Press and hold the Mobile Button for at least
four seconds
LED indication: Three blue ashes.
Audio feedback: Ascending tone (low-high).
Turn o the headset Press and hold the Mobile Button for at least
three seconds
LED indication: Three red ashes.
Audio feedback: Descending tone (high-low).
Increase the volume of
the current audio source Tap the Volume Up Button (sets and saves the volume per source)
Decrease the volume of
the current audio source Tap the Volume Down Button (sets and saves the volume per source)
Mute Simultaneously tap Volume Up and Volume
Down while any audio is on
Battery Level Indicator While on standby, press and hold the Volume
Up Button for 3 seconds
Blue light = Battery is fully charged
Red/blue light = Battery is half full
Red light = Battery is almost empty
4.2 SPOKEN STATUS ANNOUNCEMENTS
Your SRC-System™ headset oers various audio status messages
sent through your speakers. Among others, it will announce your
connection state, e.g. whether you are in mobile phone or on
intercom mode, it will conrm changes of such modes and more. By
default the feature is ON, and can be disabled as outlined below.
The Voice menu can be set at any one of the available language
options.
Entering the Voice Menu: Press and hold the CHANNEL “A” button
and CHANNEL “B” button simultaneously for 3 seconds while the
headset is on standby. Now, follow the voice instructions in English
or choose your preferred language.
Disable/Enable status announcements: While on standby, press
and hold the Volume Down Button for 6 seconds.
LED ON: indication: Solid blue + Audio feedback: One short beep
LED OFF: indication: Solid red + Audio feedback: Two short beeps
4.3 AUDIO SOURCES AND PRIORITIES
The dierent audio sources connected to the SRC-System™ are
prioritized as shown below, i.e. the higher priority source will always
override and interrupt the lower one.
For example, incoming mobile phone calls will interrupt ongoing
Intercom calls, while incoming intercom calls will interrupt the audio
from the built-in FM Radio etc.
Higher Priority 1. Mobile phone audio or GPS instructions
(device specic)
2. Intercom / Click-to-Link
3. A2DP audio source
4. FM Radio (built-in)
5. Auxiliary Line-In Port (for corded connection
e.g. MP3 players).

Lower Priority
4.4 SOFTWARE UPGRADE OPTION
In the future you will be able to install Software upgrades and program
patches to keep the software of your SRC-System™ up-to-date. Among
others, future Software upgrades will include
additional status announcements and other valu-
able functions. To ensure that you don’t miss out on the latest versions,
please register online at www.schuberth.com/src-register/en and
have your serial number ready. To download upgrades, please use the
USB cable included in the SRC-System™’s retail package.
Upgrades are only available for Windows® based computers with
XP™, Vista™ or Windows 7™ operating systems.
QG SRC 207 - MAN00015 indd 25 2/1/11 11 38 AM

26
4.5 RESETTING YOUR HEADSET
If your SRC-System™ fails to respond despite repeated attempts,
you can reset your headset by charging it. After approximately 10
seconds, remove the headset from the charger and turn it on again. It
should now respond as expected.
5. GETTING STARTED
5.1 REPLACING THE EXISTING ACOUSTIC COLLAR WITH THE
SRCSYSTEM
First, remove the existing Acoustic Collar from your helmet as follows:
1. Open both snap buttons.
2. Pull out the Acoustic Collar from the rear at its bended center.
3. Release the collar’s pins from their corresponding indentations
inside the helmets rim.
4. Now proceed and replace the existing collar with the new
SRC-System™ Acoustic Collar. As you secure the SRC-System™
into place, be sure to have the speaker cords inside the helmet.
5. Slide and insert the pin located at the edge of the control panel into it’s
corresponding indentation on the helmet and close the snap button.
Pin
6. Insert the other pin on the opposite side of the Acoustic Collar into
place and close the second snap button.
7. Push and insert the Acoustic Collar starting from the center area to
the back of the helmet area. Do the same for the remaining parts
to secure the Acoustic Collar into place.
8. Make sure that both snap buttons remain fastened, and that the
microphone boom is located on the inner side of your helmet
(between the SRC-System™ and the inner padding of the helmet).
Microphone Boom
Snap
Button
Snap
Button
Microphone
Boom
C3 helmet C2/Concept helmet
9. Make sure to close the cover of the USB connector, and then tuck
it away into the folds of the Acoustic Collar (into the back of the
Acoustic Collar on the control panel side).
5.2 POSITIONING THE SPEAKERS
For best audio results, make sure that both of your speakers are placed
as closely as possible just opposite your ears.
C2 & Concept helmets:
If you have purchased an SRC-System™ version
that ts C2 and Concept helmets, simply attach
the speakers opposite your ears onto the internal
lining by using the supplied Velcro pads.
C3 helmet:
Note: While you can attach the speakers in the same manner as explained
above (for C2 and concept helmets), we recommend that you use the
following procedure.
The following applies to both sides of the C3 Acoustic Collar:
1. Release the snap buttons on both sides of the Acoustic Collar (the
same buttons that you just fastened earlier).
QG SRC 207 - MAN00015 indd 26 2/1/11 11 38 AM

English
27
2. Open the two red buttons located at the bottom part of the
interior lining that cover the cheek pads (the
button on the back is held by a black ring).
Lift the lining slightly.
3. Attach the corresponding Velcro pad to the
identically shaped depression on the EPS (ex-
panded polystyrene) and position the speaker
on the Velcro pad.
4. Close the two red buttons. Make sure the red button is still inside
its black holding ring.
5. Now, close the snap buttons of the Acoustic Collar on both sides
and make sure they are securely fastened.
5.3 POSITIONING THE MICROPHONE
To assure smooth closing (ip-down) of the helmet’s chin section, please
remove rst its triangular Anti-Noise Pad and proceed as follows:
1. Bend the exible microphone boom as shown in the image.
2. Press the microphone towards the center of your mouth with its
large surface facing you (not the narrow one).
3. Flip-down and close the chin section of your helmet. You may
need to use both of your hands to close the chin section properly.
Chin
Section Visor
4. While the chin section is closed and the visor is open, insert your hand
into the opening of the visor and push the microphone away, towards
the center of the chin section directly opposite of your mouth.
5.4 REMOVING THE SRCSYSTEM™ FROM YOUR HELMET
1. Open both snap buttons.
2. Lift and push the Acoustic Collar’s arch from the center.
3. Release the Acoustic Collar’s pins from their corresponding indenta-
tions inside the helmet’s rim.
5.5 WEARING AND REMOVING THE HELMET
The electronic components of SRC-System™ are safely embedded
inside the Acoustic Collar. To avoid discomfort while you put on your hel-
met or while removing it, we recommend that you proceed as follows:
1. Expand the helmet opening by rmly holding the chin straps and
pulling them forcefully apart.
2. While pulling the straps apart, slide the
helmet over your head, beginning from
the neck forward.
3. To remove the helmet, proceed along the
same lines by rst pulling the straps apart
and then pushing the entire helmet upwards.
NOTE: Your SRC‑System™ Acoustic Collar is designed for maximum
comfort. However, since it contains an entire electronic kit within, it will
somewhat bulge a bit. Therefore, putting your SRC equipped helmet on or
taking it o may feel dierent than what you are used to with a standard
Acoustic Collar. Remember: The more you pull the helmet straps apart
when putting on your helmet or taking it o, the smoother the process will
be, allowing the stiness of the Acoustic Collar to decrease.
5.6 CLEANING THE ACOUSTIC COLLAR
To clean the Acoustic Collar, rst close tightly the micro USB connec-
tor of the SRC-System™. Use only a slightly damp and lukewarm cloth.
Avoid soaking the Acoustic Collar with water or any other uid. Never
submerge it and refrain from letting water come in contact with the
speakers or the microphone. Allow the unit to dry at room temperature.
QG SRC 207 - MAN00015 indd 27 2/1/11 11 38 AM

28
6. CONNECTING BLUETOOTH ENABLED MOBILE
PHONES, GPS OR MP3 (A2DP) DEVICES
Multiple Device Connectivity (“MDC”) with Bluetooth®
compatible Devices
Thanks to MDC technology the SRC-System™ oers parallel connec-
tivity as follows*:
➤ Intercom with up to two other SRC-System™ headsets
➤ Bluetooth enabled Mobile Phone / GPS device
➤ A2DP enabled MP3 Player or A2DP Adapter
Bike-to-Bike
Intercom Range*
Mobile phone
& A2DP connectivity
Built-in
FM radio
GPS
MP3
player
Bike-to-Bike
Intercom Range*
Mobile phone
& A2DP connectivity
Built-in
FM radio
GPS
MP3
player
NOTE: If you plan to use your mobile phone while using a Bluetooth® GPS
device, then you should pair your mobile phone to the GPS and not to the
SRC‑System™ headset.
* see restrictions under 9.4 b
6.1 MOBILE PHONE
To use your Bluetooth® mobile phone with the SRC-System™, you
must rst pair the two devices.
NOTE: If you plan to use a GPS device in parallel with your mobile phone, then you
should pair your mobile phone to the GPS device and not to the SRC‑System™. In
such case, skip this section and proceed directly with section 6.2.
Pairing is a one time process. Once the headset is paired to a
specic mobile phone, they will remain paired and automatically
recognize each other whenever they are within range.
If the connection between the phone and headset is lost, tap the
Mobile Button on your headset to reconnect the devices.
PAIRING THE HEADSET TO A BLUETOOTH MOBILE PHONE:
1. Turn on your phone and make sure its Bluetooth® function is activated.
Turn on your headset by pressing the Mobile Phone Button for at least
three seconds resulting in three blue ashes.
2. With the SRC-System™ turned ON, press and hold the Mobile
Button for at least six seconds until the Red and Blue Lights begin
rapidly alternating.
3. Search for Bluetooth® devices on your phone by following the phone’s
instructions. Consult your phone’s User Manual for more information.
4. After a few seconds the phone will list “SRCS” (incl. its software
version) as a discovered device. Select it and follow your phone’s
instructions to accept the pairing.
5. When prompted, enter 0000 (four zeros) as your PIN or passkey.
6. Your phone will conrm that pairing has succeeded and the headset
will begin ashing slowly in Blue.
NOTE: Not all Bluetooth® mobile phones can broadcast Bluetooth®
Stereo music (A2DP), even if the phone has an MP3 player application.
Consult your mobile phone’s User Manual for more information.
With some mobile phones, you may need to tap the Mobile Button to con-
nect the headset to the phone after pairing is complete. The SRC‑System™
will automatically connect to the last phone connected to the headset.
QG SRC 207 - MAN00015 indd 28 2/1/11 11 38 AM

English
29
NOTE: If the pairing process is not completed within two minutes the
headset will return to Standby mode.
6.2 GPS DEVICE
To use a Bluetooth® enabled GPS device with the SRC-System™, you
must rst pair the two devices. This will allow your GPS to transmit
navigation instructions and audio to the speakers of your headset.
NOTE: Not all Bluetooth® enabled GPS devices allow connections to
Bluetooth® headsets. Among others, any such GPS unit must be compatible
with the Bluetooth® “Handsfree” gateway protocol. Please consult your GPS
device’s User Manual for more information.
PAIRING THE HEADSET TO A GPS DEVICE:
1. Turn on your GPS and turn on your headset.
2. With the SRC-System™ turned ON, press and hold the Volume Up
Button for at least six seconds until the Red and Blue Lights begin
ashing simultaneously.
3. Search for Bluetooth® headsets on your GPS device by following the
device’s instructions. Consult your GPS device’s User Manual for
more information.
After a few seconds the GPS will list “SRCS” (incl. its software version)
as a discovered device. Select it and follow your GPS’s instructions to
accept the pairing.
4. If your GPS device prompts for a PIN or Passkey enter 0000 (four
zeros).
5. Your GPS device will conrm that pairing has succeeded. Your
SRC-System™ will begin ashing slowly in Blue.
6. If you wish to use a Bluetooth® mobile phone to make and receive calls
through the headset, you should pair your mobile phone to your GPS
device by following the instructions in your GPS manual.
NOTE: If the pairing process is not completed within two minutes the
headset will return to Standby mode.
NOTE: The priority schedule of your SRC‑System™ has been set in a way to
avoid incoming intercom calls to interrupt GPS instructions in progress. In such
case the intercom caller will hear a busy signal and you will hear two beeps, in-
dicating that an intercom caller is trying to page you. (see section 4.3 for details
on audio priorities of paired devices).
6.3 MP3 MUSIC WIRELESS OPTION  A2DP
Your headset is designed to receive wireless stereo music from A2DP
sources and mobile phones that support the Bluetooth® A2DP and
AVRCP proles (mostly 3rd generation devices).
Using a Bluetooth® device that supports the AVRCP prole will allow you
to operate all major A2DP source functions directly from your headset.
NOTE: The SRC‑System™ can also receive audio via the enclosed cable
from non-Bluetooth® MP3 Players or audio sources as described in
section 7.2
While listening to music from an A2DP source, you will not miss any
mobile or intercom calls, as the headset will automatically stop the
music giving preference to the incoming call. However, after you ter-
minate your call, some MP3 sources may not automatically continue
but require manual re-activation.
SETTING UP YOUR MP3 PLAYER FOR BLUETOOTH STEREO A2DP
TRANSMISSION
To use a Bluetooth® Stereo (A2DP) enabled MP3 Player or Adapter to
listen to stereo music, you must rst pair the device to your headset.
NOTE: When pairing two Bluetooth® audio devices to the SRC-System™,
please follow instructions below. Bluetooth® Stereo device pairing will
vary depending on the combination of Bluetooth® devices you are using.
PAIRING THE HEADSET TO AN MP3 PLAYER OR ADAPTER
NOTE: If your A2DP source is integrated inside your Mobile Phone, then
you should pair it with your headset as described in section 6.1 above
QG SRC 207 - MAN00015 indd 29 2/1/11 11 38 AM

30
1. Turn on your MP3 Player or Adapter, and make sure that its Bluetooth®
function is activated.
2. With the SRC-System™ headset turned ON, press and hold the
Mobile Button for at least six seconds until the Red and Blue Lights
begin alternating rapidly:
3. Search for Bluetooth® headsets on your MP3 Player by following the
device’s instructions.
NOTE: For use of a Bluetooth® adapter, follow the device’s instructions.
4. After a few seconds the MP3 Player will list “SRCS” (incl. its software
version) as a discovered device. Select it and follow your MP3
Player’s instructions to accept the pairing.
5. If your MP3 player prompts for a PIN or Passkey enter 0000 (four zeros).
6. Once pairing is complete, your MP3 Player or Adapter may conrm
that pairing has succeeded, and the headset will begin ashing
slowly in Blue.
NOTE: If the Pairing process is not completed within two minutes the
headset will return to Standby mode.
Operating your A2DP source from your headset
Play press and hold the MP3 Button for 3 seconds
Pause / Stop* press and hold the MP3 Button for 3 seconds
Forward press and hold the Volume Up Button for 3 seconds
Rewind** press and hold the Volume Down Button for 3 seconds
* Varies depending on your mobile phone
** With some phones you may need to repeat this action once more
7. BUILT-IN FM RADIO AND EXTERNAL MP3
PLAYER (CABLE OPTION)
7.1 FM RADIO
The SRC-System™ is equipped with an FM stereo radio receiver and
RDS (Radio Data System) technology.
Turn on the radio While in Standby mode, press and hold the CHAN-
NEL “B” button for 3 seconds
Turn o the radio While listening to the Radio, press and hold the
CHANNEL “B” button for 3 seconds
Switch to next
preset station
While listening to the Radio, tap the CHANNEL “B”
button to cycle through the 6 Preset FM Stations
Start Intercom call While listening to the Radio, start talking loudly
Initiate Voice Dial
from your Mobile
Phone
While listening to the Radio, tap the Mobile Button
and pronounce loudly the name of the person you
wish to call. This feature is supported only by mobile
phones that include the Voice Dial feature
Initiate Redial from
your Mobile Phone
While listening to the Radio, tap the Mobile Button
twice
RDS ON/OFF
(Default: OFF)
While the Radio is on, press and hold Volume Up and
Volume Down Buttons simultaneously for 3 seconds
Thanks to the RDS feature, your headset will automatically select the
strongest signal available for the FM station you wish to listen to, no
matter where you are riding. This allows you to leave your hands on
the handlebars at all times with no need to adjust the radio station
frequency while you are in motion.
QG SRC 207 - MAN00015 indd 30 2/1/11 11 38 AM