Schumacher SL 137-BU User manual

SL137U
SERIES
Lithium Ion 360°
LED Cordless Work Light
OWNER’S MANUAL

• 2 •
PATENT/PATENT PENDING INFORMATION
Patent Numbers Countries
WO2013/171471 PCT Number
2013261606 AUS
9851082 B2 USA
2850357 European
2502180 GB
104302963 China
2912813 Canada
1205782 HK

• 3 •
ENGLISH Original instructions
SL137U Series
Lithium Ion 360° LED Cordless Work Light
OWNERS MANUAL
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
1.1 SAVE THESE INSTRUCTIONS – This manual contains important safety and
operating instructions.
1.2 Read, understand and follow all instructions, cautions and warnings listed in this
manual. Failure to follow all instructions and abide by all cautions and warnings
could result in personal injury, injury to others and property damage.
1.3 IMPORTANT! CHARGE WORK LIGHT IMMEDIATELY AFTER PURCHASE,
AFTER EACH USE, AND AT LEAST EVERY 6 MONTHS.
1.4 DO NOT turn on the work light while it is being charged.
1.5 DO NOT handle or move the work light while it is being charged.
1.6 DO NOT look directly into the light or shine the light directly into the eyes of any
person or animal.
1.7 DO NOT allow children to use the work light.
1.8 DO NOT operate the work light if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it to a qualied service person.
1.9 DO NOT leave the battery in a discharged state.
1.10 DO NOT use the work light with a charger which has a damaged cord or plug,
replace the cord or plug immediately.
2. PERSONAL SAFETY PRECAUTIONS
WARNING! TO REDUCE THE RISK OF BURNS OR FIRE, FOLLOW THESE
SAFETY PRECAUTIONS:
2.1 DO NOT disassemble the work light; take it to a qualied service person when
service or repair is required. Incorrect reassembly may result in a risk of re.
2.2 DO NOT crush, puncture, short external contacts or dispose of in re or water.

• 4 •
2.3 DO NOT expose to temperatures above 140°F (60°C).
2.4 Recycle or dispose of the used battery as required by local regulations.
2.5 If the electrolyte in the cells gets on your skin, wash thoroughly with soap
and water. If it gets into your eyes, rinse thoroughly with cool water and seek
immediate medical attention.
2.6 This product contains a lithium ion battery. In case of re, you may use
water, a foam extinguisher, Halon, CO2, ABC dry chemical, powdered graphite,
copper powder or soda (sodium carbonate) to extinguish the re. Once the re
is extinguished, douse the product with water, an aqueous-based extinguishing
agent, or other nonalcoholic liquids to cool the product and prevent the battery
from re-igniting. NEVER attempt to pick up or move a hot, smoking, or burning
product, as you may be injured.
3. SET UP INSTRUCTIONS
3.1 Remove any cord wraps and uncoil the charging cable.
4. FEATURES
1. Horizontal magnets
2. Charging status LED indicators
3. Charging socket
4. Rotating (360°) hooks
5. 3W end LED
6. 16 SMD LED lights
7. ON/OFF power button
8. Vertical magnet
9. USB/Micro USB charging cable
123
4
5
6 7
8
9

• 5 •
5. CHARGING
IMPORTANT! CHARGE THE WORK LIGHT IMMEDIATELY AFTER PURCHASE,
AFTER EACH USE, AND AT LEAST EVERY 6 MONTHS. Failure to do this will
reduce the battery’s capacity and may void the warranty.
5.1 Connect the micro USB end of the charging cable to the micro USB port on the back
of the work light. Insert the USB end of the cable into the USB port on your charger.
5.2 Plug your charger into a live power source.
5.3 The green charging status LEDs will ash, to indicate charging has begun.
5.4 The number of green lights ashing indicates the level of charge. When the
battery has charged fully, all three LEDs will show steady green.
5.5 Recharge the work light after use, and at least every 6 months.
6. OPERATING INSTRUCTIONS
6.1 Hang the work light, using the hooks on the back. When hung from a single hook,
the work light can be rotated 360°for more precise positioning.
6.2 The magnets may be used instead. Attach to any ferrous metal surface.
6.3 Direct the lens away from your eyes before turning on the work light.
6.4 Press once to turn on the 3W end LED.
Press a second time to turn on the high-power SMD LEDs.
Press a third time to turn on the low-power SMD LEDs.
Press to turn off.
6.5 Recharge the work light after use, and at least every 6 months. VOTING
7. MAINTENANCE INSTRUCTIONS
7.1 After use and before performing maintenance, unplug and disconnect the work light.
7.2 Use a dry cloth to wipe any dirt or oil from the charging cable and case.
7.3 Any servicing should be performed by qualied service personnel.

• 6 •
8. STORAGE INSTRUCTIONS
8.1 Store inside, in a cool, dry place.
8.2 Take care to avoid/prevent damage to the charging cable and unit. Failure to do
so could result in personal injury or property damage.
8.3 Charge the work light’s internal battery immediately after purchase, after every
use and every 6 months.
8.4 All batteries are affected by temperature. The ideal storage temperature is at
70°F (21 ˚C). The internal battery will gradually self-discharge (lose power) over
time, especially in warm environments. Leaving the battery in a discharged state
may result in permanent battery damage. To ensure satisfactory performance and
avoid permanent damage, charge the internal battery every 6 months.
9. TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
The work light does
not operate. The battery is not charged. Recharge the battery to full charge.
10. SPECIFICATIONS
Battery ..............................................................(2) Lithium Ion, 3.7V, 2600 mAh
Light (main) ............................................................16 x 0.5W SMD LED, 6500K
Light (top).................................................................................. 3W LED, 6500K
Lumen output (main).................................................300 lm (low); 600 lm (high)
Lumen output (top)................................................................................... 150 lm
Ingress protection rating...............................................................................IP54
Operating time.....................Main: 12 hours (low); 6 hours (high); Top: 14 hours
Charging time.......................................................................................... 6 hours
Operating temperature.............................................14˚
– 104˚ F (-10˚ –
+40˚ C)
11. REPLACEMENT PARTS
USB to Micro USB charging cable.....................................................3899003752Z

• 7 •
12. BEFORE RETURNING FOR REPAIRS (U.S./CANADA)
When returning an item, place the original package into a shipping carton. If you
received an emailed label from Schumacher, please print the label and tape it
to the carton. Only ship via insured ground service with a tracking
number. Return shipping charges are the responsibility of the customer. We
cannot accept C.O.D. deliveries and are not responsible for lost or damaged
packages. Please do not place stickers or shipping labels on the original
manufacturer’s package. Please allow 2-3 days from date we received the
package for us to process your return. All return shipping charges must be
prepaid.
13. DISPOSAL INFORMATION
13.1 Internal battery
• The battery must be removed from the appliance before it is scrapped.
• The appliance must be disconnected from the supply mains before removing
the battery.
• The battery must be disposed of safely.
13.2 WEEE Directive
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return
and collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally-safe recycling.
Learn more about portable work lights we have.