SCOPREGA GE 2000-65 User manual

GE 2000-65
INSTRUCTION MANUAL
Catalog Number K6131100
WARNING: READ THIS MANUAL BEFORE OPERATING THE PRODUCT
SAVE THIS INSTRUCTION MANUAL FOR REFERENCE

GE 2000-65
WARNING! Read all instructions before operating the inflator. Failure to follow all instructions listed below may result in
product damage, and/or serious injury.
SAVE THESE INSTRUCTIONS
WARNINGS:
1. Read these instructions.
2. Keep these instructions.
3. Protect the cord from being walked on or pinched.
4. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way.
5. Don’t disassemble the product. Incorrect reassembly may result in a risk of Short Circuit.
6. Keep this product out of the reach of children.
DO NOT SUPPLY THE INFLATOR AT HIGHER OR LOWER VOLTAGE THAN NOMINAL. STD VOLTAGE IS 230 VAC, 50 Hz
GENERAL SAFETY RULES
1. CONSIDER WORK AREA ENVIRONMENT. Donʼt expose the device to heavy rain. Donʼt use in presence of flammable liquids
or gases.
2. DONʼT ABUSE CORD. Never carry device by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and
sharp edges.
3. STAY ALERT. Watch what you are doing. Use common sense.
4. CHECK DAMAGED PARTS. Before further use of the device, a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function.
5. DO NOT OPERATE portable device near flammable liquids or in gaseous or explosive atmospheres.
6. WARNING! RISK OF UNSAFE OPERATION. Do not modify or attempt to repair. Never drill into or make any modifications to
the device or its attachments.
INTENDED USE
GE 2000-65 is a professional inflator designed for the inflation (and deflation) of big inflatablestructures. This pump is suitable for outdoor
use.
1. THE UNIT HAS A PROTECTION DEGREE
THAT ALLOWS TO INFLATE AND
OPERATE EVEN DURING RAINING
CONDITIONS OR IN PRESENCE OF DUST.
2. THE INFLATOR IS PROVIDEDWITH HOSES
AND ADAPTORS TO BE CONNECTED TO
THE MOST COMMON INFLATION VALVES
3. THE INFLATOR IS FITTED WITH TERMAL
OVERLOAD SWITCHES THAT WILL
INTERVENE IN CASE OF OVERHEATING.
NORMAL OPERATION WILL RESUME
AUTOMATICALLY AFTER A PAUSE OF
20/40 MINUTES

GE 2000-65
MAIN CHARACTERITICS
1. Supply Voltage: 210-240 Vac; 50 Cycles
2. Max. Power 2500 W
3. Max pressure 200 mbar (500 mbar with Booster)
4. Max Flow rate 1200 l/min (2500 l/min with Booster)
5. Dimensions L700; W250; H350 (mm)
6. Mass 15 Kg
7. Protection Degree IP65 according to IEC standard 60529
USE OF GE 2000-65
TO INFLATE:
1. Connect the Inflating tube to the Outlet Port of the GE 2000-65 and to the inflatable using the fittings provided.
2. Connect the Power Supply Plug to a 230 Vac Socket
3. Turn ON the Green Switch on the Inflator.
4. Turn ON the Reed Switch to obtain the maximum
performance
5. Switch off the Green Switch when the inflatable has reached
the desired pressure
CAUTION! THE INFLATOR DOESN’T STOP
AUTOMATICALLY! IT’S NECESSARY TO CONTROL THE
DEVICE OPERATIONS IN ORDER TO AVOID THE DANGER
OF OVERINFLATION.
TO DEFLATE:
1. Connect the hose to the Inlet port using the fittings provided.
2. Turn ON the Green switch.
CAUTION! MAKE SURE THAT, DURING DEFLATION, THE UNITWILL NOT OPERATE UNATTENDED. SWITCHOFF THE UNIT
WHEN NO AIR CAN BE EXTRACTED FROM THE INFLATABLE.
TROUBLESHOOTING
Problem
Possible cause
Possible Solution
GE 2000-65 doesn’t
start
Power cord not connected
Connect the cable correctly.
Main GREEN Switch OFF (0)
Turn the switch to ON. (1)
The power cord is damaged.
Replace or repair the cable from a SCOPREGA Service
Center.
Inflator Stop
Power cord not connected
Connect the cable correctly.
Main power Switch OFF
Put the switch to ON.
Over-temperature
Wait till the GE 2000-65 has cooled down. Operation will
resume automatically
ACCESSORIES
Recommended accessories for your GE 2000-65 are available from your dealer.
WARNING: USE OF ACCESSORIES NOT RECOMMENDED FOR THIS PRODUCT CAN BE DANGEROUS.

GE 2000-65
MADE IN ITALY by
Wwww.scoprega.it