SDC S6201 User manual

P:\INST INSTRUCTIONS\EXIT DEVICES\TEMP-S6201 REV B 03-22 Page 1
TO FACE OF STOP
BACKSET 2-7/16”
40"
Watch for special
mounting height
requirements
FINISHED FLOOR
OPTIONAL 1/2”dia.
WIRE RUN
(4x) DEVICE MOUNTING HOLES
METAL: DRILL / TAP FOR 1/4"-20 MACHINE SCREWS
WOOD: PRE-DRILL 1/8" HOLES.
SEXBOLTS: DRILL 5/16" CLEARANCE HOLES ON PUSH SIDE,
3/8" HOLES ON PULL SIDE.
THIS SIDE UP FOR LHR DOOR
THIS SIDE UP FOR RHR DOOR
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email [e-mail]
TEMPLATE-S6201
Devices covered by this template:
Panic / Fire SVR Exit Device Exit Only.
801 Avenida Acaso, Camarillo, CA 93012
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [e-mail]
PLACE THIS SIDE ON FRAME STOP
FOLD HERE
CAUTION
DO NOT USE DOOR EDGE
PLACE THIS SIDE ON DOOR
3-11/16"
3-11/16"
2"
9/16"
1-3/16"
19/32"
AFTER EXIT DEVICE IS MOUNTED,
INSTALL END CAP BRACKET
CENTERED ON DEVICE C
L
OF
DEVICE
L
C
(2x) END CAP BRACKET HOLES
METAL:
WOOD:
SEXBOLTS:
DRILL / TAP FOR 1/4"-20
MACHINE SCREWS.
PRE-DRILL 1/8" HOLES.
DRILL 5/16" CLEARANCE
HOLES ON PUSH SIDE, 3/8" ON
PULL SIDE.
FRAME STOP
DOOR
FOLD HERE
2"

P:\INST INSTRUCTIONS\EXIT DEVICES\TEMP-S6201 REV B 03-22 Page 2
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
2-7/16"
1-25/32"
19/32"
7/8"
2-7/16"
3-7/32"
(3x) Top Strike Holes
METAL: DRILL / TAP FOR 1/4-20
MACHINE SCREWS
WOOD: 1/8" PILOT DRILL
TOP STRIKE
PLACE THIS SIDE ON
TOP FRAME.
PLACE THIS SIDE ON
DOOR SURFACE SIDE
FOLD HERE
(2x) TOP LATCH HOLES
METAL: DRILL / TAP FOR 1/4-20"
MACHINE SCREWS
WOOD: PRE-DRILL 1/8" HOLES
LHR DOOR EDGE OR STOP FACE
RHR DOOR EDGE OR STOP FACE
BACKSET BACKSET
ALIGN STRIKE BEFORE
INSTALLING THIS SCREW
2-3/8"
TOP LATCH
5-19/32"
C of
LATCH
L
TOP LATCH
TEMPLATE

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
2-7/16" 2-7/16"
4-11/16"
27/32"
1/4"
1-15/32
3-7/32"
1-13/16"
BOTTOM LATCH
TEMPLATE
PLACE THIS SIDE ON
DOOR SURFACE INSIDE.
PLACE THIS SIDE ON TOP OF
FINISHED FLOOR OR TOP OF
PANIC THRESHOLD
LHR DOOR EDGE OR STOP FACE
RHR DOOR EDGE OR STOP FACE
BOTTOM LATCH
DRILL Ø 3/4" HOLE
2-1/8" DEEP
Bottom Edge of Door
BACKSET BACKSET
FOLD HERE
FINISHED FLOOR
(2x) TOP LATCH HOLES
METAL: DRILL / TAP FOR 1/4-20"
MACHINE SCREWS
WOOD: PRE-DRILL 1/8" HOLES
C of
LATCH
L
(NOT REQUIRED FOR LBR DEVICE)
P:\INST INSTRUCTIONS\EXIT DEVICES\TEMP-S6201 REV B 03-22 Page 3