Sea & Sea YS-D3 DUO User manual

UNDERWATER STROBE
YS-D3 DUO
English
取扱説明書
Instruction Manual
03129

14
15
27
34
35
37

CapBolt(×2)
Diffuser
SiliconeGrease
YS-D3 ストロボボールベース

Targetlight
(P.E-13)
Fiber-opticcablesocket
(Slavesensor)(P.E-21)
Batterycap
(P.E-17)
Modeswitch
(P.E-13)
Targetlight
switch
(P.E-13)
Connectorcap(P.E-19) READY/TTLlamp
(P.E-14)
Lightlevelcontrol
(P.E-13)
Strapeyelet
(P.E-26)
Fiber-optic
cablehook
(P.E-21)
IdentificalofParts
Fiber-optic
cablesocket
(foradditional
strobe)(P.E-22)
Fiber-optic
cablesocket
(foradditional
strobe)(P.E-22)

Somedigitalcamerasoperatewiththemainflashafterdimmingwithan
advanceflash.Thisadvancedimmingiscalledapre-flash.
●Whenusingafiber-opticcable,setthemode
switchtothispositionfordigitalcameras
withpre-flashmodes.
Theemissioncolorofcharacterwillchangewithmodeselection.
Emissioncolorsareshowninthetablebelow.
Set when using the wireless RC system for cameras
manufactured by OM SYSTEMS.
Various settings can be made in the customize mode. (P.E-28)
Red
White/Blue/RedSlowFlashing
Do not turn on power with the slave sensor exposed
Always attach the "Rubber Cap for Fiber Optic Socket" to the fiber optic socket except when
attaching the fiber optic cable. If the power is turned on while the slave sensor is exposed,
the slave sensor may react to external light and emit light unexpectedly.
●
M( )
●Whenusingafiber-opticcable,setthemodeswitchtothisposition
fordigitalcameraswithoutpre-flashmodes.
●PressandholdthetargetlighttoswitchbetweenManual1andManual2.
M( )

●Thenumberoftimesadigitalcameraʼsbult-inflashwillfirediffersamong
models.Dependingonthenumberofpre-flashes,modeswitchsettings
candiffer,sochecksettingsbeforeshootingbyconductingtestflashes.
“Tocheckthemodeswitch”(P.E-23)
●[]and[]haveexactlythesameperformancewhenthestrobeis
connectedwithasynccord.
●When60minuteshaspassedfromturningonthepower,orlastemission
ofthestrobe,thepowerwillturnoffautomatically(autopower-off).When
turningonthepoweragain,setthemodeswitchto[OFF]beforesettingthe
desiredmode.
●Wheninmanualmode,thecameraremembersthestatewhenthepower
isturnedOFF,soifthepoweristurnedOFFinmanual2mode,thenexttime
thepoweristurnedON,thecamerawillstartupfrommanual2mode.
33
If the mode switch is set to [TTL] or [RC], and a
fiber-optic cable is connected, EV
compensation is performed.
Press the button and hold it down for 3 seconds in
Manual mode to switch to Manual 2 mode.

*The buzzer can be set to mute in the
customize mode. (P.J-32)
Lampdisplay BuzzeractionCondition
(temperaturelimiting)
(lightinputrestricted)
/Buzzer
・

BallMountStrobeAdaptor/YSMountStrobeAdaptor
ABallMountStrobeAdaptorisincludedwiththisproductasstandard
equipment.
ByreplacingitwiththeoptionalYSMountAdaptor,youcanselecta
mothodforattachmenttoahousingthatmatchestheshootingconditions.
How to attach optional YS Mount Strobe Adaptor
M4

Attach optional YS Mount Adaptor in either direction
The optional YS Mount Adaptor can be
fixed to the Strobe in either direction. The
fixing bolt wing nut will be on the opposite
side to the metal nut inserted in YS Mount
Adaptor.
If attaching the unit to an arm or other accesory, insert the fixing bolt
from the side of the YS Mount Strobe Adaptor which does not have a
nut inserted and tighten to secure.
●Removethefixingboltfromtheproductwhenstoring.Duetoprolonged
use,theYSMountmaybecomeslightlywarped,makingitdifficultto
attachanddetachtheArm.

Settingandcableusedtoconnecttothismodelcanvarydependingonthe
camera/hausingmodel.
Thevariousconnectionmethodsusingdifferentcablesaredescribedbelow.
Referto“TakingPhotographs”onpageE-23fordetailsontakingphotographs
whenconnectedwithdifferentcables.
●PleasecheckthepoweristurnedOFF
whenyouareinstallingasynchro
cord.Thereisapossibilityoferroneous
fireifconnectingwhenpowerisON.
RC