Sea & Sea YS-D3 User manual

UNDERWATER STROBE
YS-D3 LIGHTNING
日本語 English
取扱説明書
Instruction Manual
03123

14
15
27
29
30
31

CapBolt(×2)
Diffuser
SiliconeGrease
YS-D3 ストロボボールベース

Targetlight
(P.E-13)
Fiber-optic
cablesocket
(foradditional
strobe)(P.E-22)
Fiber-opticcablesocket
(Slavesensor)(P.E-21)
Batterycap
(P.E-17)
Modeswitch
(P.E-13)
Targetlight
switch
(P.E-13)
Connectorcap(P.E-19) READY/TTLlamp
(P.E-14)
Lightlevelcontrol
(P.E-13)
Strapeyelet
(P.E-26)
Fiber-optic
cablehook
(P.E-21)
IdentificalofParts
Fiber-optic
cablesocket
(foradditional
strobe)(P.E-22)

Somedigitalcamerasoperatewiththemainflashafterdimmingwithan
advanceflash.Thisadvancedimmingiscalledapre-flash.
●Whenusingafiber-opticcable,setthemodeswitchtothisposition
fordigitalcameraswithoutpre-flashmodes.
●Whenusingafiber-opticcable,setthemode
switchtothispositionfordigitalcameras
withpre-flashmodes.
Theemissioncolorofcharacterwillchangewithmodeselection.
Emissioncolorsareshowninthetablebelow.

●Thenumberoftimesadigitalcameraʼsbult-inflashwillfirediffersamong
models.Dependingonthenumberofpre-flashes,modeswitchsettings
candiffer,sochecksettingsbeforeshootingbyconductingtestflashes.
“Tocheckthemodeswitch”(P.E-23)
●[]and[]haveexactlythesameperformancewhenthestrobeis
connectedwithasynccord.
●When30minuteshaspassedfromturningonthepower,orlastemission
ofthestrobe,thepowerwillturnoffautomatically(autopower-off).When
turningonthepoweragain,setthemodeswitchto[OFF]beforesettingthe
desiredmode.
●InTTLmode,modestatussetatthetimeofpoweroffissaved,and
therefore,ifthepoweristurnedoffwhiletheunitissettoSLAVE-TTL
mode,theunitwillstartupinSLAVE-TTLmodeatnextpowerup.
33

fire.
Illuminates
Red
Blinks Red Charging Ready to fire (Gn 22)
Ready to fire (Gn 33)
Blinks Orange
Blinks Green
Blinks
Light-Blue
Blinks Blue
AftershootingwithTTLautmaticlight
controliscompletedandtheTTLlamp
willilluminateingreenforapproximately
2seconds.

BallMountStrobeAdaptor/YSMountStrobeAdaptor
ABallMountStrobeAdaptorisincludedwiththisproductasstandard
equipment.
ByreplacingitwiththeoptionalYSMountAdaptor,youcanselecta
mothodforattachmenttoahousingthatmatchestheshootingconditions.
How to attach optional YS Mount Strobe Adaptor
M4

Attach optional YS Mount Adaptor in either direction
The optional YS Mount Adaptor can be
fixed to the Strobe in either direction. The
fixing bolt wing nut will be on the opposite
side to the metal nut inserted in YS Mount
Adaptor.
If attaching the unit to an arm or other accesory, insert the fixing bolt
from the side of the YS Mount Strobe Adaptor which does not have a
nut inserted and tighten to secure.
●Removethefixingboltfromtheproductwhenstoring.Duetoprolonged
use,theYSMountmaybecomeslightlywarped,makingitdifficultto
attachanddetachtheArm.

Settingandcableusedtoconnecttothismodelcanvarydependingonthe
camera/hausingmodel.
Thevariousconnectionmethodsusingdifferentcablesaredescribedbelow.
Referto“TakingPhotographs”onpageE-23fordetailsontakingphotographs
whenconnectedwithdifferentcables.
●PleasecheckthepoweristurnedOFF
whenyouareinstallingasynchro
cord.Thereisapossibilityoferroneous
fireifconnectingwhenpowerisON.