13 Mode F: Four Colour Sequence: Red>Green>Blue>Purple
Mode E: RGB Colour Sequence: Red>Green>Blue
11
Auto Colour Change
12
1White
2Green
4Green+Blue
6Red+Blue
8Mode B: Green+Gradual Red
3Blue
5Red+Green
9Mode C: Blue+Gradual Green
7Mode A: Blue+ Gradual Red
10 Mode D: Blue+Gradual Red
14 Rapid Auto Colour Change
SAFETY WARNINGS
• Avoid direct contact with electrical power.
• Understand all regulations in effect for preventing accidents.
• Switch off power to transformer before repairing or replacing the light.
• Never handle with wet hands and feet.
• This unit is design for use only when fully submerged in water, please use
with suitable transformer.
• Never operate this Underwater Light for more than 1 minute unless it is totally
submerged in water.
• This product should be installed according to your local electrical installation
ordinances and regulations.
• Maximum Depth for Light installation at 1 meter.
o
• Maximum Water Temperature Range for light operation 0 - 30 C.
SPECIFICATION
A. Electrical Specification : 1) Voltage : AC12V 2) Frequency : 50/60Hz
3) Power : 10W.
B. Colour change options(For RGB version only)
• Only qualified electrician is allowed to carry out the installation of this product.
www.emauxgroup.com
E-Lumen Compact
UNDERWATER LIGHT OPERATING MANUAL
Keep this manual for future reference
Model：ELCOMP-N ELCOMP
8-1 8-2
8-3 8-4
CONTROL
1. When the light is connected to the
transformer directly, the on/off switch
controls the colour changes (a light with a
transformer with an on/off switch is
recommended; If you want all the lights to
change colour at the same time, please
install a master switch, Figure 1).
2. If applicable, when the light is connected
to the transformer and the transformer to
the optional control box, the control panel
on the control box and its remote control
controls the colour changes (See the
Control Box Manual for details).
Figure 1
ON/OFF Switch
Light
Transformer
Light
Transformer
Master Switch
Light
Transformer
ON/OFF Switch ON/OFF Switch
≤30m
Transformer
Light
Figure 2
INSTALLATION NOTES
1. Each cable have 2.5m long. Please follow the procedures when installing the
light.
2. It is recommended to install a light in every 4m , the approximate exposure
area of each unit.
3. The lights should be installed in the direction that they will not shine directly
into the house.
2
Figure 3
Concrete must be cut background
niche to allow for a compact plaster
seal
Rigid conduit
Junction box 120cm min.
Water level
45cm min. from water line to top of lens
INSATALLATION OF THE UNDERWATER LIGHT
A. Preparing to Install
1. Before installation, a circuit system diagram must be designed by a certified
engineer.
2. The circuit system must comply with local laws and regulations and must be
carried out by qualified electricians.
3. Make sure the voltage is 12V and the terminal box is at least 120cm from the
poolside (Figure 3).
4. Upon installation, top of the light must be at least 45cm from water surface
(Figure 3).
B. Pool Installation
1. Embed the Shell into the concrete wall, making sure that it is parallel to the
side of the pool (Figure 4).
2. Place the Mounting Plate on the concrete wall and tighten it with 6 screws.
(Figure 5).
3. Note that the light must only be installed on a flat or concave surface.
4. Wrap extra cables behind the light to make sure it could be taken to the pool
surface for future maintenance .Then tighten the nut or line pipe joint
(Figure 6).
5. Hang the light onto the Mounting ring and tighten the screws (Figure 7).
6. The wire connections inside the terminal box must be sealed by leak-proof
tapes to prevent water from leaking into the terminal box through the cables.
4. For training or competition pools, the lights must be installed on the sides in
order to prevent swimmers from seeing any glare.
5. Nothing should be placed on the poolside directly above the lights for ease of
future maintenance.
6. Please ensure all wires and connections are sealed and waterproofed to
avoid any damage.
2
7. The cables connecting the lights and the transformers must be at least 6mm
and the distance between them must not exceed 30m (Figure 2); otherwise
the lights will not function properly.
Figure 4 Figure 5
Figure 6
or
Figure 7
80g印尼蓝
双面印刷,对折成A6(折后看到1和2页）
2014.06
1 : 1
105X148(mm)
PANTONE Process Black C
材 料
工 艺
日 期
EMAUX E-Lumen Compact水灯 英文说明书
EMLI14060701
名 称
版 本 编 号
规 格
比 例
颜 色
产品负责人
更改日期
更改内容
新文件
版本 制图/设计
A
意万仕(中山)泳池设备有限公司
EMAUX ZhongShan)Swimming P o o l Equipment C o . , Ltd(
审核 批准
EMLI14060701
