Sealey Cp40mc User manual

1.1 ELECTRICAL SAFETY.

REGARDING DIRECT MAINS POWER USE WITH THE

CHARGING BASE AND PLUG ONLY.

WARNING! It is the owner’s responsibility to read, understand

and comply with the following electrical instructions:

You must ensure the risk of electric shock is minimised by the

installation of appropriate safety devices. An RCCB (Residual

Current Circuit Breaker) should be incorporated in the main

distribution board. We also recommend that an RCD (Residual

Current Device) is used with all electrical products, particularly

portable equipment which is plugged into an electrical supply

not protected by an RCCB.You must also read and understand

the following instructions concerning electrical safety.

The Electricity At Work Act 1989 requires all portable•

electrical appliances, if used on business premises, to be

tested by a qualified electrician, using a Portable

Appliance Tester (PAT), at least once a year.

The• Health & Safety at Work Act 1974 makes owners of

electrical appliances responsible for the safe condition of the

appliance, and the safety of the appliance operator. If in any

doubt about electrical safety, contact a qualified electrician

Battery Charger Safety Instructions•

 WARNING! DO NOT use the charging base to charge any

battery other than that required for the tool. Other types of

batteries may explode!

Inspect the plug, cable and the charging base for wear

and damage to ensure items are safe before connecting to the

mains power supply. If worn or damaged DO NOT use,

immediately replace, or contact a qualified electrician.

Check cables are always protected against short circuit and

overload.

Uncoil the power cable between the plug and the charging base

before use.

 DO NOT pull or carry the charging base by the charger power

lead, or pull the plug from the mains socket by the power lead.

 DO NOT use any other type of transformer with the charging base.

 DO NOT try to open or dis-assemble the plug or charging base.

 DO NOT use the plug to power any other electrical item.

Disconnect the plug from the charging base and the mains

power supply when not in use.

 DO NOT expose the charging base to damp or wet conditions

(for indoor use only).

 DO NOT pull or carry the charging base by the power lead.

 DO NOT operate the charging base if it has been dropped, or

has received a sharp knock, or is damaged. Contact an

authorised service agent.

 DO NOT dismantle the charging base as this may cause

damage or personal injury and will invalidate your warranty.

 DO NOT insert foreign objects or material into the hole

reserved for the battery.

 DO NOT immediately charge a second battery. Consecutive

charging will overheat the charging base. Allow the unit to cool

for 15 minutes before charging the next battery.

Ensure that the insulation on all cables and on the appliance is

safe before connecting it to the power supply.

Ensure that cables are always protected against short circuit

and overload.

DO NOT use worn or damaged cables, plugs or connectors.

Immediately have any faulty item repaired or replaced by a

qualified electrician.

When a BS1363/A UK 3 pin

plug is damaged, cut the cable

just above the plug and dispose

of the plug safely.

Fit a new plug according to the

following instructions (UK only).

a) Connect the GREEN/

YELLOW earth wire to the

earth terminal ‘E’.

b) Connect the BROWN live

wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all

wires have been correctly connected, that the cable outer

insulation extends beyond the cable restraint and that the

restraint is tight. Double insulated products, which are always

marked with this symbol ,are fitted with live (brown) and

neutral (blue) wires only.

DO NOT connect either wire to the earth terminal.

1.2 BATTERY SAFETY INSTRUCTIONS.

 WARNING! Battery contains lithium-ion which is dangerous.

Handle with care to avoid damage, fire, corrosion or personal

injury.

Charge battery prior to its first use. The battery will have

been shipped in a low charge state.

 To reduce the risk of burns or fire:

 DO NOT Attempt to open, disassemble, modify or service the

battery pack.

 DO NOT Crush, puncture, short external contacts or dispose of

in fire or water.

 DO NOT Expose to temperatures above 40°C (104°).

 Replace only with the battery pack designated for this product.

 Recycle or dispose of used battery as stipulated by local

regulation.

Use only the charging base provided to charge the charger

battery.

 DO NOT attempt recharging the battery by means of an engine

generator or a DC power source.

 WARNING! Dispose of spent batteries correctly as they contain

Lithium-ion. DANGER! DO NOT attempt to disassemble the

battery. For safety and environmental reasons DO NOT discard

in domestic waste or by burning. ONLY discard or recycle

according to local authority regulations.

 WARNING! DO NOT allow a leaking battery to contact your

person. If you come into contact with battery liquid take the

following immediate action:

a) Skin contact: Wash immediately with soap and water,

then wash flesh in either lemon juice or vinegar.

 b) Eye contact: Wash with a strong solution of boric acid,

and seek immediate medical attention.

1. SAFETY INSTRUCTIONS

CP40MC Issue: 1 - 06/07/09

INSTRUCTIONS FOR:

LITHIUM-ION 12V MAINS

CHARGER - 1 HOUR

MODEL No: CP40MC

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly

maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND

CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY

CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.

FUSE RATING

5 AMP

Blue

Neutral

Wire

Yellow & Green

Earth Wire

Cable

Restraint

2. INTRODUCTION & SPECIFICATIONS

Recharges Sealey 12V Lithium-ion battery (Model No: CP40BP) in 1

hour. LED's indicate when charging and when charging is complete.

Intelligent charging process maximizes battery life.

Input Supply: ................................................................. 230V AC 50hz

Output:........................................................................... 12V DC - 1.5A

Weight: ........................................................................................0.5 kg

Battery Model No (not included): ...........................................CP40BP

3. CHARGING

CHARGING THE BATTERY (NOT INCLUDED, ORDER

MODEL No: CP40BP)

Note:When new, the battery will have been shipped in a low charge

state. Fully charge the battery before using your tool

3.1 To remove the battery from the charger, depress the two

side clips on the battery. DO NOT touch the metal battery

terminals.

3.2 Take the base charger and plug it into the mains.

3.3 The battery is designed to fit into the charger one way

only. This is to ensure that the positive (+) and negative (-)

polarities correspond. Insert the battery and press lightly to

seat the battery firmly into the charging base, as in fig.1.

WARNING! DO NOT try to force battery into the base the

wrong way around.

3.4 When the battery is inserted into the charger the green LED

(fig.1) will begin to flash, this indicates the battery is charging.

3.5 When the green LED (fig.1) stops flashing and is solid the

battery is fully charged.

3.6 If the red LED (fig.1) illuminates the battery is too hot to charge

and will need to cool down before the charging cycle begins.

3.7 If the red LED (fig.1) flashes this means either the battery is

not seated in the charger correctly or the battery is defective

and should be replaced.

3.8 Remove the battery from the charger. Switch off and remove

the plug from the mains. Push the battery back into the

charger (fig.2) until it snaps into place. The charger is now

ready for use.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

Declaration of Conformity We, the sole importer into the UK, declare that the products listed here are in conformity with the following standards and directives.

The construction files for this product are held by the Manufacturer and may be inspected, by a national authority, upon

request to Jack Sealey Ltd.

For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Tools.

Signed by Tim Thompson 6th July 2009

MAINS CHARGER

Models: CP40MC

2004/108/EC EMC Directive

2002/95/EC RoHS Directive

2002/96/EC WEEE Directive

93/68/EEC CE Marking Directive

2006/95/EC Low Voltage Directive

CP40MC Issue: 1 - 06/07/09

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner

which is compatible with the environment.