Sealey Sdh50110v User manual

110V 50L INDUSTRIAL DEHUMIDIFIER

MODEL NO: SDH50110V

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLYAND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR

PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

1.1. ELECTRICAL SAFETY

WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and

any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate

safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend

that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a

supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by

contacting your Sealey stockist.

9You must also read and understand the following instructions concerning electrical

safety.

1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if

used on business premises, are tested by a qualified electrician, using a Portable

Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances

responsible for the safe condition of those appliances and the safety of the appliance

operators. If in any doubt about electrical safety, contact a qualified electrician.

9Ensure that the insulation on all cables and on the appliance is safe before connecting

it to the power supply.

9Ensure that cables are always protected against short circuit and overload.

9Regularly inspect power supply cables and plugs for wear or damage and check all

connections to ensure that none are loose.

9Ensure that the voltage marked on the appliance matches the power supply to be

used.

8DO NOT pull or carry the appliance by its power supply lead.

8DO NOT pull the plug from the socket by the power cable.

8DO NOT use worn or damaged cables, plugs or connectors. Immediately have any

faulty item repaired or replaced by a qualified electrician.

9Ensure the unit is correctly earthed via a three-pin 110V plug.

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘PE’.

b) Connect the BROWN live wire to the live terminal ‘L/+’.

c) Connect the BLUE neutral wire to the neutral terminal.

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends

past the cable restraint and that the restraint is tight.

1.2. GENERAL SAFETY

9 Checkthatthedehumidierisinsoundconditionandgoodworkingorder.Takeimmediateactiontorepairorreplacedamagedparts.

9Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

8DO NOT stand or place any object less than 10cm from the front or rear of the unit.

8DO NOTobstructtheairintakesoroutletsofthedehumidier.

8DO NOT place any object into the outlets - the unit has a fan running at high speed, contact with this will cause injury.

8DO NOToperatethedehumidierwhenyouaretiredorundertheinuenceofalcohol,drugsorintoxicatingmedication.

8DO NOTswitchthedehumidiero󰀨bydisconnectingitfromthemains.ALWAYSswitchtothe“OFF”positionrst.

8DO NOTremovetheoatleverfromthewatercollectiontank.

8DO NOT connect or disconnect the plug from the mains with wet hands.

9Always discard the water from the collection tank, DO NOT use it for any other purpose.

9 Placethedehumidieronalevelandstablesurface.

8DO NOTusethedehumidieratambienttemperaturesbelow5°C.

8DO NOTusethedehumidieroutside.

8DO NOT use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.

9 Theapplianceshallbestoredinaroomwithoutcontinuouslyoperatingignitionsources(forexample:openames,anoperatinggas

appliance or an operating electric heater.)

8DO NOT pierce or burn.

SDH50110VIssue212/07/2021

Original Language Version

Refer to

instructions Do not cover Indoor use only Caution:

Riskofre

9Be aware that refrigerants may not contain an odour.

9When using continuous draining, make sure that the drain hose is positioned correctly.

9 Ensurethatheatingappliancesarenotexposedtotheowofairfromthedehumidier.

9 Beforeattemptingtomovethedehumidier,emptythecontentsofthecollectiontank.

9 Switcho󰀨anddisconnectitfromthemainsbeforeattemptinganycleaningorothermaintenancework.

9 Ensurethatthedehumidieriscorrectlyturnedo󰀨whennotinuse,andstoredinasafe,dryarea,outofreachofchildren.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental

capabilities or lack of experience or knowledge if they have been given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

WARNING: If the power cord is damaged, it must be replaced by a professionally trained person.

2. INTRODUCTION

Powerfuldehumidicationcapacity,extractsupto50litresofwaterperday.Removesexcessmoisturefromair,preventingbuild-upofmildew

andmould.Featuresauto-defrostfunction,whichactivatesiftheroomtemperaturefallstoolow.Theunithasa24hrtimerfunctionfordelay

startingandautoshut-o󰀨.Washableactivatedcarbonairlter.RefrigerantisenvironmentallyfriendlyR290.Maybeconnectedtoadrainhose

forcontinuousoperation.Mountedoncastorsformanoeuvrability.Fittedwith110Vplug.

3. SPECIFICATION

MODEL NO:.......................................................................................SDH50110V

Freezing Pressure (Max):........................................................................... 2.5MPa

Global Warming Potential (Rating):.......................................................................3

IP Rating:........................................................................................................IP22

MaximumAirow:.....................................................................................300m³/hr

Power:...............................................600W(27°CRH60%)800W(30°CRH80%)

Refrigerant:.......................................................................................... R290/0.2kg

Steaming Pressure (Max): ......................................................................... 1.0MPa

Supply:............................................................................................................110V

Working Space:....................................................................................... 50-120m³

Working Temperature:................................................................................. 5-35°C

g.1

SDH50110VIssue212/07/2021

Original Language Version

4. ASSEMBLY

4.1. WHEEL INSTALLATION: Take the machine body, wheel axle, wheel and screws out of the packaging case, and lay the machine

 bodydown.AsshowninFig.2,xthewheelaxleonthemachinebodywith4screws,andxawheelatbothendoftheaxle. 

Return the unit to an upright position after attaching the wheels.

4.2. HANDLE INSTALLATION:marryuptheholesinthebracketswiththeholesinthebottomofthehandle.Itmaybeusefultoxthe

 screwsinthelowerholesrst,thenipthehandleupwards,andsecureitwiththescrewsintheupperholes.

Note: Once assembled, DO NOT use for 2 hours.

5. OPERATION

5.1. WATER TANK USAGE: You may use the water tank in two ways.

5.1.1. DIRECT USE. When the water tank is full, the machine automatically shuts down and enters the standby state, the LED displays

 the“FullWater”signalandthedehumidierwillalarm.Whenthewatertankisemptiedandputinplaceagain,thedehumidiercan

continue its performance.

5.1.2. CONTINUOUS DRAINAGE.AsshowninFig.3,torestoretheperformanceofthewatertank,youneedtotakeoutthewatertank,

and mount the drain pipe.

Note: When using continuous drainage, the drainage pipe shall not be set higher than the water tank.

5.2. FUNCTION DESCRIPTION

g.2

g.3

BUTTON OPERATION INSTRUCTIONS

ON/OFF ChangesbetweenSwitchonandSwitcho󰀨.

+Adjustdi󰀨erentsetvaluesindi󰀨erentstates;

1.Increasesthehumidityvalueset(RH10%to95%)

2.Increasesthetiming(hour)set(00to24)

-Adjustdi󰀨erentsetvaluesindi󰀨erentstates;

1.Decreasesthehumidityvalueset(RH10%to95%)

2.Decreasesthetiming(hour)set(00to24)

Timing Shortpressthebuttontolaunchacycletoo󰀨.

Seton/o󰀨TimerandExit

SDH50110VIssue212/07/2021

Original Language Version

NOTE:  Efficiencyofthedehumidifierisinfluencedbytheairoutsidetheroom.Foroperatingefficiency,trytoavoidopeningandclosingthe

 windowsanddoors.Forbestperformance,operatethedehumidifierwithintheusableoperatingtemperature.

5.3. OPERATION

5.3.1. Plug the unit in to the mains socket, a beep will be heard when inserting the plug.

5.3.2. Pressthe“ON/OFF”switchandtheoperationlightwillilluminate,thehumiditydisplaywilllighttodisplaytheprevioussethumidity. 

 Theinitialsettingforhumidityis60%,after3secondsthedisplaywillshowthecurrenthumidity.

5.3.3. Press the humidity up or down buttons to adjust to the desired humidity required.

 Iftherequiredhumidityis3%belowthecurrenthumiditytheunitwillstartautomatically,ifthesethumidityis3%morethanthecurrent

humidity the dehumidifier will automatically stop.

5.3.4. Whensettingthehumiditytolessthan30%,theunitwillruncontinuouslyandthedisplaywillread“CO”.

5.3.5. Toshutthedehumidifierdownpressthe“ON/OFF”switch.

NOTE: If the humidity setting is greater than the current humidity the unit will not run.

WARNING! The fan motor and compressor must run for at least 3 minutes while dehumidifying.

8DO NOTstartthedehumidierimmediatelyaftershuttingdown,allow3minutesbeforerestarting.

5.4. TIMER FUNCTION

5.4.1. TosetTimerforpowerONmode,withtheunitinpowerOFFstate,presstheTimerbutton(g.4.6).TheTimerONLED(g.4.1)will

 ickerandthecurrentsettimewillbedisplayed.UsetheIncrease/Decreasebuttons(g.4.10,g.4.11)tosettherequiredvalueto

 between0and24hours.After10secondstheselectedvalueissetandtheTimerONledwillicker.

5.4.2. TosettheTimerforpowerOFFmode,withtheunitinpowerONstate,presstheTimerbutton(g.4.6).TheTimerOFFLED(g.4.1)

 willickerandthecurrentsettimewillbedisplayed.UsetheIncrease/Decreasebuttons(g.4.10,g.4.11)tosettherequiredvalueto

 between0and24hours.After10secondstheselectedvalueissetandtheTimerOFFledwillicker.

5.5. DEFROSTING

5.5.1. Thedefrostingdeviceworksautomaticallyatanintervalofapproximatelyevery30minutesforadurationofapproximately5minutes

when the coil temperature is tested to be <= minus 1oC.

The dehumidifying function will stop during the defrosting operation. DO NOT disconnect the plug or turn off the unit during the

 defrostingoperation.Thedefrostingledlight(fig.4.7)willlightup.

NOTE: This dehumidifier does not have a cooling function, it produces heat during the operation and room temperature will rise

 by1°Cto4°C.Thetemperaturegetshigherwhileitisoperatedinacloset,orsimilar.Furthermore,roomtemperaturewillrisebecause

doors and windows are closed and heat is produced from other appliances in the room and from sun radiation.

5.6. EMPTYING THE WATER COLLECTION TANK

5.6.1. During the dehumidifying operation, water is collected in the water collection tank. When the tank is full of water, the dehumidifier stops

operating automatically and the warning buzzer beeps twice. The unit will not restart until water collection tank has been emptied.

5.6.2. Open the door and remove water collection tank from the dehumidifier by pulling it gently outwards by holding the sides of the tank.

5.6.3. Hold the tank by the handle and carry it carefully to an emptying point.

5.6.4. Remove the plug at the bottom of the tank and slowly empty the water out of the tank.

5.6.5. Replace the drain plug and refit the tank in the dehumidifier, making sure it is properly back in place as the unit will not restart if it is

not fitted correctly.

5.7. CONTINUOUS DRAINING

5.7.1. If there is a place suitable for draining, continuous draining can be carried out. The continuous operation enables the dehumidfying

 operationtocontinueuninterrupted.SeeSection5.1.

6. MAINTENANCE

6.1. CLEANING THE AIR FILTER

6.1.1. The dehumidifying capacity is lowered when the air cleaning filter becomes clogged.

6.1.2. Open the front door of the unit.

6.1.3. Lift up the filter element from the bottom and lift out of the holder.

6.1.4. To dislodge the dust from the filter, use a vacuum cleaner or tap it lightly.

6.1.5. If the filter is very dirty, wash it carefully in water with a neutral detergent, then rinse well with clean water and leave until dry.

6.1.6. To refit the air filter locate the top of the element into the locating bracket at the top of the door and then locate the lower section into

the lower bracket.

6.1.7. Close the door of the dehumidifier.

6.2. STORAGE

6.2.1. Unplug the unit, bundle the power cord, and hang the bundled cord at the back of the unit.

SDH50110VIssue212/07/2021

Original Language Version

ITEM OPERATION

1 Timer Indicator

2 Temperature Indicator

3 DehumidicationIndicator

4Humidity Indicator

5ON/OFFControl

6 Time Set Control

7Defrosting Indicator

8 Air Speed Indicator

9WaterFullIndicator

10 Increase Control

11 Decrease Control

1234 5 6

78910 11

g.4

6.2.2. Remove the water collection tank and empty the water out of it. Remove the tank cover and wash the inside of the tank with clean

water. The tank may be scratched if it is scrubbed strongly with a brush. DO NOT remove the float lever from the tank. Wipe off the

water on the outside of the tank with a cloth. Refit the tank cover onto the tank and replace the tank in position.

6.2.3. Clean the air filter (see 6.1).

6.2.4. When the unit is to be stored for a long time, wipe the dehumidifier over with a dry soft cloth. To remove dirt, wipe over with a very

slightly dampened cloth (never use a wet cloth for cleaning the controls). To avoid deformation or cracking, do not use benzine,

thinner or liquid cleaners.

6.2.5. When storing, place in a safe, dry, childproof location. Stand the unit upright and avoid exposure to direct sunlight.

7. TROUBLE SHOOTING

7.1.  Uponfaultofthedehumidier,pleasecuto󰀨thepowersupplyimmediately,unplugtheplugandcheckthefollowingitems:

7.2. If the said methods still fail to eliminate the above problems, please directly contact the manufacturer or agents. DO NOT disassemble

 thedehumidier,contactSealeyforrepairs.

Faults Cause Analysis Solutions

Fails to turn on

Shown as no power

No power to the wall socket. Check the power supply.

Check the plug plugged in

properly. Plug the power supply in the socket.

Check the fuse is not blown. Replace the fuse.

Power Transformer is broken. Replace the transformer.

Shown as power on

Environmental humidity lower

than the set value. Set again according to the demand.

If the water tank is installed

correctly. Place the water tank in right position.

If the entire machine is defrosting. Wait for the completion of defrosting cycle.

Unfavourable

dehumidifyinge󰀨ect

If the air inlet/outlet is obstructed. Remove the obstacle.

If the door and window are open. Close the door and window.

If the indoor temperature is too low. Don’trunthedehumidier.

Heavy noise Ifthegroundisrmandat. Resettlethedehumidier.

Dehumidierisstoodprecariously. Resettlethedehumidier.

Water leakage Dehumidierstoodonanincline. Movedehumidiertoalevelsurface.

Drain pipe/outlet obstructed. Dismantle the front plate to eliminate blockages.

E1 Coil sensor fault Turn to timing for defrosting, to cancel system fault

function.

E2/E3 Fault of humidity & temperature sensor. Replace the humidity & temperature sensor.

EE Refrigerant leakage. Start the machine after. Ask for help from

professionalsifthe“EE”signalremains.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior

notice.

Important: No Liability is accepted for incorrect use of this product.