Sealey MC454E User manual

MOTORCYCLE LIFT 450KG - 12V ELECTRO/
HYDRAULIC
MODEL NO.: MC454E
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Disconnect lift from power supply before changing parts, servicing or performing any maintenance.
9Ensure lift is kept clean and in good working order. Immediately repair or replace damaged parts.
9Use recommended parts only. Incorrect parts may be dangerous and will invalidate the warranty.
9 Useaqualiedpersontolubricateandmaintainthelift.DO NOTusebrakeuidtotopupsystem.UseSealeyhydraulicoilonly.
9Locate lift in a suitable, well lit work area. Keep area clean and tidy and free from unrelated materials.
9Use lift on level and solid ground, preferably concrete, capable of withstanding the weight of the lift and any load placed on it.
9Avoid tarmacadam since lift may sink in.
9Ensure all non-essential persons keep a safe distance.
9Always keep your hands and feet away from moving parts. DO NOT reach under the lift.
8DO NOT operate the lift if parts are missing or damaged.
8DO NOT adjust the safety overload valve.
9Keep the lift clean for best and safest performance.
9The maximum load is 450kg. DO NOT exceed this rated capacity.
9Use this lift for lifting purpose only. NOT to be used for lifting persons. DO NOT use it for any other purpose it is not designed to
perform.
9Keep children and unauthorised persons away from the work area.
9 Removeillttingclothing.Removeties,watches,ringsandotherloosejewellery,andcontainlonghair.
9Keep proper balance and footing, DO NOT overreach and wear non-slip footwear.
9Ensure the vehicle is adequately secured to the lifting platform with appropriate straps.
9Before lowering lift ensure that there are no obstructions underneath and that all persons are standing clear.
8DO NOT use the lift if damaged, any suspect parts are noted or it has been subjected to a shock load.
8DO NOToperatetheliftwhenyouaretiredorundertheinuenceofalcohol,drugsoranyintoxicatingmedication.
8DO NOT allow untrained persons to operate the lift.
8DO NOTmakeanymodicationstothelift.
8DO NOT get the lift wet.
9When not in use remove power supply, and store in the down position in a safe, dry, childproof area.
WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product,
but must be applied by the operator.
2. INTRODUCTION
All steel construction with a 450kg capacity. 12V Electro/Hydraulic lifting system for simple, fast operation. Can be powered by a 12V vehicle
batteryoraRoadstartunit.Supportplatformfittedwithfullwidthloadingramp.Suppliedwithmotorcyclefrontwheellockingattachmentfortyre
widthsupto135mmtoassistinsecuringthevehicle.Fittedwithmulti-positionsafetylocktopreventaccidentallowering.Suitableforuseina
garage or shed without the need of mains 230v electricity supply or for a mobile mechanic or race pits. Designed for use with centre or side stand
motorcycles or with a rear paddock stand.
3. SPECIFICATION
Model no:.................................................................MC454E
Capacity:......................................................................450kg
Minimum height:.........................................................215mm
Maximum height:........................................................760mm
Platform Width: ..........................................................650mm
Platform Length:.......................................................1828mm
ElectricalPowerSupply: ..................................................12V
MC454E Issue 1 10/10/22
Original Language Version
©JackSealeyLimited
Refer to
instructions Wear protective gloves Wear safety
footwear No reaching inWarning:
Crushing of
Hands

4. FEATURES
5. ASSEMBLY
WARNING! The lift is very heavy. Use appropriate mechanical
lifting equipment.
NOTE: Item numbers refer to attached Parts list.
5.1.  Openthepackageandxthe4LiftingPins,washersandlock
nuts (items 5 / 29 / 30 ) to the edge of the frame.
5.2.  Useropes/stropsxedtothe4LiftingPinsandlifttheliftout.
NOTE: Thepumptankislledwithoil.DO NOT incline it
when lifting, so as to avoid the oil being poured out.
5.3. POWER UNIT PREPARATION
5.3.1. Remove the power unit assembly from the package, lift the
handle, align the notch then tighten with two set screws.
5.4. BASE FRAME, SIDE EXTENSIONS and RAMP (item 35, 16)
5.4.1. Raise the base frame slightly and insert the two short support leg
 assembliesintotheframeintheappropriatepositionandxin
 placeusingtheSafetyLatches(item36).
5.4.2. SlideRamp(item16)intoplaceandxwithcotterpin(item17).
5.5. HYDRAULIC CONNECTION (g 1)
5.5.1. Connect the hydraulic hoses of the power unit and base frame with quick connector, connect the two wires of the power unit to the
battery, then press the lifting switch to raise the platform.
5.6. WHEEL CLAMP (refer to Parts List)
5.6.1. FixWheelClamps(items44,46)inplaceusingxingsprovided.
5.6.2. FixBa󰀪ePlate(item45)inplaceusingxingsprovided.
6. OPERATION
WARNING!Ensurethatyouhaveread,understandandapplytheSection1SafetyInstructions.
WARNING! DO NOT overload the lift. The maximum load is 450kg.
9Position the lift in a suitable location, preferably on a concrete surface, capable of withstanding the weight of the motorcycle/vehicle
and the lift.
WARNING! The motorcycle needs to be fully supported by the platform prior to lifting. The ramp (item 16) is only used to assist
the operator in wheeling the vehicle on to the platform when the lift is at its lowest position.
6.1. Wheel the motorcycle onto the lift and secure the front wheel into the clamp at the front of the lift.
6.2.  SecurethemotorcycletotheliftusingtheLiftingPins(items29)andappropriatestrapping.
6.3. The motorcycle lift already has hydraulic oil added before shipping.
6.4. Once connected to the power, the lift can be used immediately.
6.5. Remove the ramp (item 3) before lifting the platform.
6.6.  Standwellbackfromtheliftwhenliftingorloweringplatformtoavoiddanger.Usetheliftingswitch(g.1)toraisethelift.
6.7. Once at its desired height, lower the lift so that the safety brake engages.
6.8. LOWERING
6.8.1. Check there are no tools, equipment, cables or hoses under the lift.
6.8.2. The safety brake needs to be manually disengaged prior to lowering. Raise the lift to allow the safety brake to be released.
6.8.3. As the lift is completely lowered, the safety brake automatically engages ready for ascending.
NOTE: The safety brake only engages once the lift is completely lowered, NOT if the lift is stopped during descent and raised
 again.InthisinstancethesafetybrakeMUSTbemanuallyengaged.
Original Language Version
©JackSealeyLimited MC454E Issue 1 10/10/22
ITEM DESCRIPTION
1 Platform
2 Wheel Clamp
3 Ramp
4 Base Frame
5 Power Unit
6 Lifting Frame
7Safety Device
g.1
Quick Connector
To
Battery
Lifting
Switch

7. MAINTENANCE
7.1. Clean and lubricate on a regular basis.
7.2. Before each use check all parts. If any part of the lift is damaged or suspect, remove the lift from service and take
necessary action to repair.
7.3.  Regularlycheckoillevelviallerhole.Withpistonfullydownremovellerplug,oilshouldbelevelwithbottomofllerhole. 
 Top-upasnecessary.UseagoodqualityjackoilsuchasSealeyHydraulicJackOil.DO NOTusebrakeuid.
7.4.  Ensurenodirtentershydraulicsystemwhenllingorremoving/replacingcomponents.
7.5.  Keeptheliftcleanandwipeo󰀨anyoilorgrease.Lubricateallmovingparts.
Original Language Version
©JackSealeyLimited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
REGISTER YOUR
PURCHASE HERE
MC454E Issue 1 10/10/22