Sealey SA9302 User manual

3.1 INSTALLATION FOR BOTH MODELS
3.1.1 AIR SUPPLY - MAXIMUM PRESSURE 12bar (175psi)
The supply must be clean and dry - use a suitable filter/water trap if necessary. The supply pressure at the gauge
inlet should ideally be 10bar (145psi).
Note: Maximum tyre inflation pressure cannot exceed the supply pressure.
1. SAFETY INSTRUCTIONS
3Disconnect the gauge from the air supply before changing accessories, servicing or performing any maintenance.
3Maintain the gauge in good condition (use an authorised service agent), and keep the gauge clean for best and safest
performance.
3Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate
the warranty.
3Locate gauge in a suitable work area, keep area clean and tidy and free from unrelated materials and ensure there is
adequate lighting.
3Keep children and unauthorised persons away from the work area.
7DO NOT direct gauge outlet at yourself or at other persons or animals.
7DO NOT carry by the hose, or yank the hose from the air supply.
7DO NOT use the gauge for a task which it is not designed to perform.
7DO NOT operate the gauge when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7DO NOT operate gauge if parts are missing or the gauge is damaged, as this may cause failure and/or personal injury.
2. INTRODUCTION & SPECIFICATIONS
3. INSTALLATION
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS FOR FUTURE USE.
SA9302 & SA9312 - 1 - 091105
INSTRUCTIONS FOR:
PROFESSIONAL AIR LINE GAUGES
MODELS: SA9302 & SA9312
SA9302: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with 500mm rubber hose
and single clip-on connector.
SA9312: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with 500mm rubber hose
and a twin push-on connector.
SPECIFICATION. SA9302 SA9312
Range: 0-10bar (145psi). 0-10bar (145psi).
Air Supply Maximum: 12bar (175psi). 12bar (175psi).
Inlet: 1/4BSP Male. 1/4BSP Male.
Connector: Single clip. Twin push on.
Hose: 500mm rubber. 500mm rubber.
SA9312
SA9302
Clip-on Connector
Twin Push-on Connector
Operating Lever
Gauge
1/4BSP Male

5. MAINTENANCE & SERVICE
PERIODIC CHECKS AND MAINTENANCE
For long service and accuracy, the following actions should be carried out at the recommended intervals.
5.1 WEEKLY - CHECK OPERATION
The gauge should be checked weekly for correct operation. Look for smooth lever operation and fast, smooth gauge
movements. Check for leaks from tyre connector seals, and for chafing or wear of the flexible hoses. Any problems
should be immediately rectified.
5.2 QUARTERLY - CHECK CALIBRATION
We recommend the accuracy of the gauge be checked against a calibrated master gauge every 3 months, or at shorter
intervals depending on operators own quality procedures.
4. OPERATION
4.1 ATTACH ADAPTOR TO VALVE
Push and hold the connector onto the tyre valve using the most convenient side of the twin valve connector (SA9312).
For SA9302, squeeze the thumb clip on the connector, push the connector onto the tyre valve and release the clip.
The connector will now be locked in place.
4.2 TO INFLATE
Momentarily depress the operation lever fully, then release to display tyre pressure. When reading the pressure, hold the
gauge flat with respect to the eye to minimise error.
Fully depress operation lever for an appropriate period. Avoid over inflation, release lever frequently to check the pressure.
4.3 TO DEFLATE
Depress lever half-way (until air can be heard escaping) for an appropriate period. Fully depress lever momentarily then
release to display new pressure.
IMPORTANT - ALWAYS FULLY DEPRESS LEVER MOMENTARILY BEFORE READING TYRE PRESSURE.
SA9302 SA9312
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of these products.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
[e-mail]
www.sealey.co.uk
Web
email
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
SA9302 & SA9312 - 1 - 091105