Sealey SG14 User manual

SG14 - -250902
Instructions For:
UNDER-BODY COATING GUN
Model: SG14
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY,
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
pWARNING! Disconnect the gun from the air supply before changing accessories, servicing or performing
any maintenance.
3Maintain the gun in good condition. Replace or repair damaged parts. Use recommended parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
3Keep the gun clean and rinse out nozzle and pipes with thinners after use.
p p
WARNING! If gun components become blocked there is a danger of excessive pressure building up in unit
causing the canister to burst.
3Locate the gun in a suitable, well ventilated area, keep area clean, tidy and free from unrelated materials and
ensure there is adequate lighting.
3Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3Keep children and unauthorised persons away from the working area.
3Avoid unintentional operation.
3Ensure coating/wax manufacturers instructions are carefully followed.
7DO NOT hold gun or attachments close to your face (especially eyes, ears, etc.) and do not point gun or air
hose at other persons or animals.
7DO NOT carry by the air hose, or yank the hose or the gun from the air supply.
7DO NOT use the gun for any purpose other than for which it is designed and do not use with any other fluid.
7DO NOT operate the gun if damaged.
3When not in use disconnect from the air supply and store in a safe, dry, childproof area.
2. INTRODUCTION & SPECIFICATION
2.1. Introduction
2.1.1. The SG14 is used for anti-rust treatment of vehicles and agricultural machines by the application of underseal
compound or wax.
3.1 Air Supply
3.1.1 Ensure air valve is in "off" position before connecting to the air supply.
3.1.2. An air pressure of no more than 90psi and an air volume of 8cfm will be required.
3.1.3. pWARNING! Ensure air supply does not exceed 90psi. Too high a pressure will shorten the
product life and may be dangerous, causing damage and/or personal injury.
3.1.4. Drain air supply tank daily. Water in the air line will damage the gun and will invalidate your warranty.
3.1.5. Clean air inlet filter screen weekly. For recommended hook-up, see figs.1.a,b,&c.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The
minimum hose and fittings diameter should be 10mm I.D.
3.1.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3.2. Couplings.
3.2.1. Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome
this, connect a leader hose to the wrench. A quick change coupling may then be used to connect the leader
hose to the air line recoil hose. See fig.1. a, b & c.
3. PREPARING THE GUN FOR USE
Fig 1a
Fig 1b Fig 1c
SG14 - -250902
Instructions For:
UNDER-BODY COATING GUN
Model: SG14
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY,
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
pWARNING! Disconnect the gun from the air supply before changing accessories, servicing or performing
any maintenance.
3Maintain the gun in good condition. Replace or repair damaged parts. Use recommended parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
3Keep the gun clean and rinse out nozzle and pipes with thinners after use.
p p
WARNING! If gun components become blocked there is a danger of excessive pressure building up in unit
causing the canister to burst.
3Locate the gun in a suitable, well ventilated area, keep area clean, tidy and free from unrelated materials and
ensure there is adequate lighting.
3Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3Keep children and unauthorised persons away from the working area.
3Avoid unintentional operation.
3Ensure coating/wax manufacturers instructions are carefully followed.
7DO NOT hold gun or attachments close to your face (especially eyes, ears, etc.) and do not point gun or air
hose at other persons or animals.
7DO NOT carry by the air hose, or yank the hose or the gun from the air supply.
7DO NOT use the gun for any purpose other than for which it is designed and do not use with any other fluid.
7DO NOT operate the gun if damaged.
3When not in use disconnect from the air supply and store in a safe, dry, childproof area.
2. INTRODUCTION & SPECIFICATION
2.1. Introduction
2.1.1. The SG14 is used for anti-rust treatment of vehicles and agricultural machines by the application of underseal
compound or wax.
3.1 Air Supply
3.1.1 Ensure air valve is in "off" position before connecting to the air supply.
3.1.2. An air pressure of no more than 90psi and an air volume of 8cfm will be required.
3.1.3. pWARNING! Ensure air supply does not exceed 90psi. Too high a pressure will shorten the
product life and may be dangerous, causing damage and/or personal injury.
3.1.4. Drain air supply tank daily. Water in the air line will damage the gun and will invalidate your warranty.
3.1.5. Clean air inlet filter screen weekly. For recommended hook-up, see figs.1.a,b,&c.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The
minimum hose and fittings diameter should be 10mm I.D.
3.1.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3.2. Couplings.
3.2.1. Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome
this, connect a leader hose to the wrench. A quick change coupling may then be used to connect the leader
hose to the air line recoil hose. See fig.1. a, b & c.
3. PREPARING THE GUN FOR USE
Fig 1a
Fig 1b Fig 1c

01284 757500 E-mail: [e-mail]
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor
Sealey Group, Bury St. Edmunds, Suffolk.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogue
on 01284 757525 and leave your full name and address including your postcode.
p p
WARNING! Ensure you read, understand and apply the safety
instructions in Section 1 and follow the manufacturers instructions on
the underseal/wax container.
4.1. Screw on a canister of schutz underbody coating.
4.2. Ensure air supply is regulated to no more than 6 bar (90psi) and then attach
air hose to the gun.
4.3. Aim the nozzle of the gun into a safe area and depress the gun trigger to
check for correct operation.
4.2. Injection probe.
4.2.1. The SG14 is supplied with an injection probe (fig.2.A) for use with wax.
The flexible probe enables wax to be sprayed into cavities, between panels
and inside doors etc.
4.2.2. The probe fits in place of the nozzle.
4. OPERATING INSTRUCTIONS
Fig 2
A
5. PARTS
Item Part No Description Item Part No Description
1142-BU098204 Body 6142-BT098159 Spout
2142-BH058042 Valve, complete 7142-BS098158 Nozzle, outer
3142-BF078138 Pin 8142-BS098161 Lock nut
4142-BE078250 Trigger 9142-BU098211 Tank connection
5142-BS078146 Nozzle, inner 10 142-BT098156 Suction pipe
Issue: 1
Date: 250902
SG14 - -250902
01284 757500 E-mail: [e-mail]
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor
Sealey Group, Bury St. Edmunds, Suffolk.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogue
on 01284 757525 and leave your full name and address including your postcode.
p p
WARNING! Ensure you read, understand and apply the safety
instructions in Section 1 and follow the manufacturers instructions on
the underseal/wax container.
4.1. Screw on a canister of schutz underbody coating.
4.2. Ensure air supply is regulated to no more than 6 bar (90psi) and then attach
air hose to the gun.
4.3. Aim the nozzle of the gun into a safe area and depress the gun trigger to
check for correct operation.
4.2. Injection probe.
4.2.1. The SG14 is supplied with an injection probe (fig.2.A) for use with wax.
The flexible probe enables wax to be sprayed into cavities, between panels
and inside doors etc.
4.2.2. The probe fits in place of the nozzle.
4. OPERATING INSTRUCTIONS
Fig 2
A
5. PARTS
Item Part No Description Item Part No Description
1142-BU098204 Body 6142-BT098159 Spout
2142-BH058042 Valve, complete 7142-BS098158 Nozzle, outer
3142-BF078138 Pin 8142-BS098161 Lock nut
4142-BE078250 Trigger 9142-BU098211 Tank connection
5142-BS078146 Nozzle, inner 10 142-BT098156 Suction pipe
Issue: 1
Date: 250902
SG14 - -250902