Sealey Stw101 User manual

7Ensure all workshop safety rules, regulations, and conditions are complied with when using torque wrench.

3Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine

parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

7The wrench is a precision tool, DO NOT abuse it. DO NOT drop or throw the wrench.

3Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

WARNING! DO NOT use the wrench if damaged or thought to be faulty (contact Service Agent).

7DO NOT use wrench unless you have been instructed in its use by a qualified person.

7DO NOT use any cleaner which might affect the high pressure grease with which the wrench is packed.

3After use adjust to lowest torque setting (but not below),clean and store in a safe, dry, childproof location.

2.1. Introduction

These torque wrenches are precision tools and each is supplied with a calibration certificate. Torque setting is by means of a micrometer type adjuster and the drive

head has a reversible ratchet.

2.2. Specifications

Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly maintained, give years of trouble free performance.

INSTRUCTIONS FOR: TORQUE WRENCHES

Models: STW101, STW1011, STW102,

STW103, STW104, STW200,

STW201 & STW202

1. SAFETY INSTRUCTIONS

2. INTRODUCTION & SPECIFICATIONS

3.1. Hold torque wrench in left hand (if right handed) so that

required scale - on shaft, just above hand grip - is uppermost

and visible.

3.2. Turn the lock screw, in the end of the grip, anticlockwise to unlock

grip (STW201 has a locking plug in the end of the grip - pull ring

to unlock).

3.3. Turn grip to select torque setting as follows:

 Required setting - 56Nm

 Turn grip until top edge is level with the 50Nm line on the shaft

scale and the zero on the grip graduation is aligned with the

centre line of the shaft scale.

 Rotate the grip further, clockwise, until the 6 on the grip

graduation is aligned with the centre line to give a setting of 50

+ 6 = 56Nm, lb.m, lb.ft or kg.m.

Note: If using the alternative scale ( in.lb, ft.lb or m.kg depending

on wrench) then each division of the grip graduation is equivalent

to the scale increment divided by the number of divisions. For

example (STW1011):

The alternative scale is in lb.ft.

Scale increments are 5.16lb.ft

There are 7 grip divisions.

Then each division is 5.16/7 = 0.74lb.ft

3.4. Tighten lock screw at end of handle to prevent accidental

alteration of the setting.

3.5. When tightening the nut/bolt you will feel and hear the wrench

mechanism click when the set torque is reached. Immediately stop

applying force to wrench to avoid over-tightening the nut/bolt.

Wrench will reset ready for the next application.

Note: If wrench is not used for some while, operate it a few times,

at a low setting, to ensure all internal parts are coated in grease.

3. OPERATION

4. RECALIBRATION

5. CALIBRATION CERTIFICATE

To ensure continued accuracy the wrench should be recalibrated

annually and after any impact or other misuse. Contact

an NAMAS accredited laboratory.

STW101, STW1011, STW102, STW103, STW104, STW200, STW201, STW202 - 1 - 271004

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect

use of this equipment. WARRANTY: Guarantee is

12 months from purchase date, proof of which will

be required for any claim. INFORMATION: For a

copy of our latest catalogue and promotions call

us on 01284 757525 and leave your full name and

address, including postcode.

See over for the Calibration Certificate for this wrench.

Sole UK Distributor,

Sealey Group, Bury St. Edmunds, Suffolk.

01284 757500 sales@sealey.co.uk www.sealey.co.uk

01284 703534 e-mail Web

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

STW101 STW1011 STW102 STW103 STW104 STW200 STW201 STW202

Torque Range (Nm) . .5-25 . . . . . . .7-112 . . . . . .40-210 . . . .70-420 . . . . .140-700 . . . . . .20-80 . . . . . .30-210 . . . . .50-560

Alternative Scale . . . .44-221lb.in . .5-83lb.ft . . . .30-155lb.ft . .52-310lb.ft . .103-516lb.ft . . .20-110lb.ft . . .20-150lb.ft . .50-400lb.ft

Drive (sq) . . . . . . . . .1/4 . . . . . . .3/8 . . . . . . .1/2 . . . . . . .3/4 . . . . . . .3/4 . . . . . . . . . .3/8 . . . . . . . .1/2 . . . . . . .3/4

Length (mm) . . . . . . .275 . . . . . . .370 . . . . . . .460 . . . . . . .850 . . . . . . .1070 . . . . . . . . .405 . . . . . . . .535 . . . . . . .675

Pounds

Feet

(lb.ft)

Kilogram

Metres

(kgm)

Newton

Metres

(Nm)

Newton

Metres

(Nm)