Sealey VS703.V5 User manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
BEARING RACE & SEAL
DRIVER SET - 10 PIECE
Model No: VS703.V5
1. SAFETY INSTRUCTIONS
 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
WARNING! Always wear approved eye protection when using the driver. Failure to do so may result in serious
injury. Normal spectacles are not adequate protection.
Familiarise yourself with the specific applications and limitations of the driver, as well as any potential hazards.
If unsure of the applications or limitations of the driver, contact your supplier.
Ensure that the driver is the correct tool for the task. DO NOT use the driver for any purpose other than that
for which it is designed.
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
Ensure that the workpiece is stable and that there is adequate lighting.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Use the correct size and type of hammer for the task. The recommended diameter of hammer face is 10mm
larger than tool head. Check that the hammer shaft is in good order and is firmly secured in the hammer
head. Note that for seal installation a soft-faced hammer should be adequate and will be less likely to
damage the tool.
Make sure that the face of the hammer and the head of the tool are clean and free from grease, oil, etc.
Position the tool so that it is struck away from your body.
Strike the driver squarely on the head - DO NOT hit the tool off centre, or at an angle (fig.1).
 DO NOT use the driver if it is bent, chipped, has a mushroom head, or is otherwise damaged (fig.2).
 DO NOT strike the side of the driver body (fig.3).
 DO NOT use driver if any parts are damaged or missing as this may cause failure and/or personal injury.
 DO NOT use the driver when you are tired or under the influence of alcohol, drugs or intoxicating medication.
Keep children and unauthorised persons away from the working area.
When not in use, pack into the case, and store in a safe, dry, childproof location.
fig.3
fig.2
fig.1
Original Language Version VS703.V5 Issue: 1 - 12/09/11
Incorrect

2.1. Contents
2.1.1. Check the contents (see parts below) and contact your supplier if any items are missing or damaged.
2.2. Usage
2.2.1. Remove bolt (fig.4.B) from handle (fig.4.A).
2.2.2. Select the correct adaptor (fig.4.C), one which is slightly smaller than the diameter of the seal/bearing
race, and position it correctly on the handle, secure it using the bolt.
2.2.3. Place the seal/bearing race (fig.4.E or F) in the mouth of the housing (fig.4.D), place adaptor against it
and tap the driver handle to force it into place (fig.5).
2. OPERATION
3. PARTS
ALWAYS WEAR SAFETY GOGGLES WHEN USING DRIVERS
Users of drivers are reminded that damage to the striking faces can take place and we
recommend that safety goggles are worn when using this tool.
VS703.V5-00 HANDLE
VS703.V5-01 ADAPTOR, 39.5mm
VS703.V5-02 ADAPTOR, 44mm
VS703.V5-03 ADAPTOR, 50mm
VS703.V5-04 ADAPTOR, 59mm
VS703.V5-05 ADAPTOR, 63mm
VS703.V5-06 ADAPTOR, 64.5mm
VS703.V5-07 ADAPTOR, 72mm
VS703.V5-08 ADAPTOR, 76mm
VS703.V5-09 ADAPTOR, 81mm
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version VS703.V5 Issue: 1 - 12/09/11
fig.5
fig.4