Sealey SX272.V2 User manual

LOCKING WHEEL NUT REMOVAL SET 10pc
MODEL NO: SX272.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! DO NOT use the tool if damaged or thought to be faulty.
WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to
when using tools.
WARNING! If jacking up a vehicle refer to manufactures instructions for vehicle and jack.
8DO NOT use the tool for a task it is not designed to perform.
8DO NOT use worn, or damaged sockets.
8DO NOT use the tool unless you have been instructed in its use by a qualied person.
8DO NOT operate the tool if you are tired or under the inuence of alcohol, drugs or intoxicating medication.
9Maintain the tool in good condition.
9Follow all workshop safety rules, regulations and conditions.
9 Maintain correct balance and footing. Ensure the oor is not slippery and wear non-slip shoes.
9Keep children and non essential persons away from the working area.
2. INTRODUCTION
Conical shaped design allows socket to fit over locking/wheel nut. Socket is hammered onto nut using the punch, so nut and socket wedge
together. Nut can then be removed with a breaker bar or impact wrench. Set also includes drift to remove nut from socket.
3. SPECIFICATION
Model No:..............................................................................................................SX272.V2
Drive: .........................................................................................19mm and 22mm Hex Drive
19mm Maximum Internal Sizes: .............................................................. Ø18, 19, 20, 21mm
22mm Maximum Internal Sizes ..................................................................... Ø23, 24, 25mm
SX272.V2 Issue 1 22/05/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves

4. OPERATION
4.1. Select the appropriate removal socket to create a tight t over the wheel nut.
4.2. Fit the socket over the wheel nut and insert the punch (g.1).
4.3. Using a suitable hammer, strike the punch sharply several times until the socket has gripped the wheel nut.
4.4. Place either a wrench or impact socket over the hex at the rear of the removal socket.
4.5. Release the wheel nut by turning as a unit with the removal socket.
4.6. Hold the removal socket in a vice and pass the drift through the rear end of the socket and strike the drift to release the wheel nut
(g.2).
WARNING: Take care when removing the nut from the removal socket: the nut can exit the socket with considerable force.
5. MAINTENANCE
5.1. Clean the inside of the socket with abrasive paper or cloth to remove any dirt or irregularity.
5.2. Keep the kit clean and store all the components in the case after use.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
g.1
g.2
SX272.V2 Issue 1 22/05/18
Original Language Version
© Jack Sealey Limited