DISC SANDER 305MM
MODEL NO: SM31.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power
supply.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure
that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the
plugisttedwiththecorrectfuse-seefuseratingintheseinstructions.
8DO NOT pull or carry the appliance by the power cable.
8DO NOT pull the plug from the socket by the cable.
8DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is
replacedimmediatelybyaqualiedelectrician.
ThisproductisttedwithaBS1363/A13Amp3pinplug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensurethatrepairsarecarriedoutbyaqualiedelectrician.
ReplaceadamagedplugwithaBS1363/A13Amp3pinplug.Ifindoubtcontactaqualiedelectrician.
a)ConnecttheGREEN/YELLOWearthwiretotheearthterminal‘E’.
b)ConnecttheBROWNlivewiretotheliveterminal‘L’.
c)ConnecttheBLUEneutralwiretotheneutralterminal‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealeyrecommendthatrepairsarecarriedoutbyaqualiedelectrician.
1.2 GENERAL SAFETY
9Familiarise yourself with the product’s application and limitations, as well as the specific potential hazards peculiar to the machine.
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.
WARNING! Disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.
WARNING! DO NOT sand any materials containing asbestos.
WARNING! Wearapprovedsafetyeye/faceprotection.Ifdustisgeneratedrespiratoryprotectionmustbeworn.
9Maintain the sander and keep in good condition (use an authorised service agent).
9Check the alignment of moving parts regularly, for safest performance keep the sander clean at all times.
9 Usethecorrecttypeandsizeofsandingdiscforthissander.
9 Beforeeachusechecksandingdiscforcondition.Ifwornordamagedreplaceimmediately.
9 Replaceorrepairdamagedparts.Usegenuinepartsonly.Non-authorisedpartsaredangerousandwillinvalidatethewarranty.
9Locate the sander in a suitable area, keep area clean, uncluttered and ensure there is adequate lighting.
9The sander is for indoor use only. DO NOT get the sander wet or use in a damp location.
9Ensure the sander is situated on a solid work surface, adequate for supporting the weight of both the sander and the workpiece.
9Ensure there are no flammable or combustible materials near the work area.
9Remove ill fitting clothing, ties and loose jewellery, and tie back long hair.
9 Maintaincorrectbalanceandfooting,ensurethefloorisnotslipperyandwearnon-sliprubbersoledfootwear.
9Keep hands and body clear of the worktable when operating the sander.
9Ensure there are no nails, screws etc. protruding from the surface to be sanded.
8DO NOT operate the sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8DO NOT leave the sander running unattended.
9Hold workpiece firmly, avoiding hand positions where a slip may cause your hand to come into contact with the sanding disc.
8DO NOT modify or change the sander motor for one with a different rating.
8DO NOT turn the sander on until work table is clear of all objects, wood scraps etc.
Recommended fuse rating
13Amp
SM31.V3|Issue:4(3)13/11/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Weareye
protection
Wearprotective
gloves
Wearear
protection
Wearamask Indoor use only
