Sealey RB951 User manual
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.1 GENERAL SAFETY
Familiarise yourself with this product's application and limitations, as well as any specific potential hazards peculiar to the beacon.
Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
DO NOT use the beacon for any purpose other than for which it is designed.
DO NOT allow children to operate the beacon.
DO NOT operate the beacon if any parts are missing or damaged as this may cause failure or possible personal injury.
When not in use switch the beacon off and where appropriate remove plug from power supply.
2. TECHNICAL SPECIFICATIONS
Voltage:...................................................................................12V-24V dc
Type of Bulb:.................................................H1 12V 55W - H1 24V 55W
Index of protection (EN 60598-1):.....................................................IP56
Operating Temperature:....................................................-30°C to +50°C
Radio Interference Filter:................................... EC95/54 EMC approved
Rotational Speed:...........................................................160 rpm nominal
Approvals:......................................................................................ECE65
3 . INTRODUCTION AND FIxING
Model No’s: RB951, RB952, RB953, RB954, RB955.
Instructions for:
ROTATING BEACONS
12/24Volt
various ttings
● SealeyrotatingbeaconsaredesignedtomeetthestrictestEuropeanstandards.
● European,British,andlocallawsmustbeobservedwhenusingthebeacon.
● Heavy-dutyABSbase.
● QuickreleaseUVstabledomewillnotfadeinprolongedsunlight.
● Suppliedwith12Vand24Vbulbs.
● Reversepolarityprotected.
RB951
ø128mm
Overall height: 200mm
Length of mounting: 40mm
RB952
ø170mm
Height: 140mm
RB953
ø165mm
Height: 235mm
RB955
ø165mm
Height: 235mm
3.1 RB951: 12mm Single Bolt Fixing
Fixing Instructions:
3.1.1 Drill a 13mm mounting hole in a suitable point on the vehicle.
3.1.2 Connect to cables of at least 2mm² section and use an 8Amp fuse; check polarities.
3.1.3 Fix the beacon by using nuts and washers according to the type and shape of the mounting
surface.
RB951,RB952,RB953,RB954,RB955 Issue: 1 -10/10/12
© Jack Sealey Ltd Original Language Version
ø128mm
Height: 170mm
RB954
3.2 RB952: Three Bolt Fixing Base
Fixing Instructions:
3.2.1 Drill mounting holes using the beacon base as a template (3 holes of 6.5mm diameter at 120° on a 130mm diameter
circumference). Also make provision to route cables into the vehicle.
3.2.2 Connect to cables of at least 2mm² section and use an 8Amp fuse; check polarities.
3.2.3 Fix the beacon with 3 x M6 screws. (Not supplied).
3.3 RB953: Fixed Spigot Base
● UseinconnectionwithDINspigot (a range of DIN mountings is available: please see Sealey catalogue).
● DINadaptormountstovehicleallowingremoval/installationwithouttools.
● Suitableforsituationswheresecurityisaproblem.
Fixing Instructions:
3.3.1 Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical.
3.3.2 Usecablesofatleast2mm²sectionandusean8Ampfuse;checkpolarities.
3.3.3 Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut.
3.3.4 When the beacon is removed, always close the adapter socket outlet using the rubber cap.
3.4 RB954: Magnetic Base
● Fittedwithhighpowermagnetstrongenoughtocopewithnormalroadspeeds.
● Suppliedwith3mtrcoiledflexanduniversalauxilliarypoweroutletplug.
3.4.1 The beacon must be placed on a surface parallel to the ground.
3.4.2 The surface should be flat and clean to ensure good adherence.
3.5 RB955:Flexible base with DIN spigot mounting.
Fixing Instructions:
3.5.1 Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical.
3.5.2 Usecablesofatleast2mm²sectionandusean8Ampfuse;checkpolarities.
3.5.3 Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut.
3.5.4 When the beacon is removed, always close the adapter socket outlet using the rubber cap.
4 . VOLTAGE SELECTION
To change voltage, simply fit bulb of appropriate voltage (see section 5). An internal voltage regulator will ensure correct flash speed.
5 . CHANGING THE BULB
WARNING - NEVER TOUCH THE GLASS BULB WITH YOUR BARE HANDS! The natural acid will etch the glass and
shorten the life of the bulb.
5.1 Remove the globe by turning anti-clockwise to unlock and lifting clear.
5.2 Rotate the mirror for easy access to the bulb. This can be achieved
when beacon is switched off by turning the drive worm gear with a
finger tip.
5.3 Prise the wire clip clear of the bulb base to release.
5.4 Pull the bulb clear and remove the connector beneath the base.
5.5 Replace bulb and reassemble.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No responsibility is accepted for incorrect use of this equipment.
WARRANTY: Guarantee is 12 months from purchase date. Proof of purchase will be required for any claim.
INFORMATION: Please call us for a copy of our latest catalogue on 01284 757525, leaving your name, address and postcode.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park, Bury
St. Edmunds, Suffolk,
IP32 7AR
RB951,RB952,RB953,RB954,RB955 Issue: 1 -10/10/12
© Jack Sealey Ltd Original Language Version
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed
of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for
recycling information.
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
This manual suits for next models
5
Table of contents
Other Sealey Security System manuals
