Sealey GSC110385 User manual

INSTRUCTIONS FOR
GALVANIZED STEEL FLOOR CABINET 5 SHELF
EXTRA WIDE
MODEL NO: GSC110385.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this cabinet.
9Locate cabinet in a suitable work area.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use cabinet on level and solid ground, preferably concrete.
9Keep the cabinet clean and tidy in accordance with good workshop practice.
9Keep children and unauthorised persons away from the work area.
8DO NOT use the cabinet for any purpose other than that for which it is designed.
8DO NOT use the cabinet outdoors.
8DO NOT place the cabinet in a damp or wet location or an area where there is condensation.
8DO NOT clean the cabinet with any solvents which may damage the surfaces or the protective coating.
8DO NOT move the cabinet when there are items placed inside.
8DO NOT step on the shelves.
8DO NOT overload the cabinet.
2. INTRODUCTION
Floor standing galvanized steel cabinet with lockable double doors. Fitted with ve shelves, four of which are adjustable. Supplied with four
keys. Ideal for factory, workshop or home use. Features two rear wiring grommets allowing power tool batteries and other devices to be
charged whilst in storage. Floor cabinet is supplied at packed and will need some simple assembly.
3. SPECIFICATION
Model No....................................................... GSC110385.V2
Overall Size (W x D x H) ..................... 1100 x 410 x 1830mm
Shelf Size................................................1090 x 365 x 20mm
Shelves ................................................................................5
4. ASSEMBLY
4.1. Unpack the unit and conrm that all the parts listed.
4.2. Assemble the unit on a solid level surface.
4.3. The assistance of a second person will be required.
4.4. To assemble the unit you will require a rubber mallet and a Phillips-head screwdriver.
4.5. Where practical x unit to a wall for extra strength and durability.
GSC110385.V2 | Issue 1 24/10/16
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear protective
gloves

Step 1
Insert and slide front base bracket (E1) and back base
bracket (F1) into the bottom of left side panel (B1) and
right side panel (B2) as per diagram above. Attach
brackets using a self tapping screw (J) in each of
the four corners as shown in the diagram (g.1).
Step 2
Stand unit upright and install the left back panel (C1)
followed by the right back panel (C2). Fix the back
panels with self tapping screws (J) as per the diagram
(g.2). At this stage, x all screws except those marked
with a cross. You will need an extra pair of hands to
assist from the opposite side while you x the screws.
Step 3.
Insert the middle column (G1) into the hole in the front base bracket (E1). Fix it using a self tapping screw (J) from the back. Install
the top panel (A1) and x it using self tapping screws (J) as per the diagram (g4). Install shelf supports (I) in the middle column
(G1) and in all four corners level for each designated height and then insert the shelves (D1).
GSC110385.V2 | Issue 1 24/10/16
Original Language Version
© Jack Sealey Limited
g.1
g.2
g.3

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
[e-mail]
01284 757500
01284 703534
GSC110385.V2 | Issue 1 24/10/16
Original Language Version
© Jack Sealey Limited
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Step 4.
Install the right door (R1) and left door (L1) using the bottom hinge pins (K) and latches on the top. The space between the doors and
the top panel can be adjusted using washers (M) if necessary. Insert wiring grommets (N) into pre-cut holes in back panel.
g.4