Sebo Airbelt K3 User manual

OWNER’S MANUAL
For ousehold Use Only

Technical Details 2
How To Contact SEBO 2
Important Safety Instructions 3
Special AIRBELT K Product Features 4
AIRBELT K2 Features 4
AIRBELT K3 Features 5
Optional Attachments, Accessories, Bags and Filters 5
Standard Features of All SEBO Vacuums 6
Identification of Parts 7
Standard Attachments 7
Brushes and eads 7
Assembly 7
Operating Instructions 8
Starting the Machine 8
Suction Control 8
Operating the Machine 8
Additional Operating Instructions for K3 with Power Head 9
Starting the Machine and Suction Control 9
Operating the Machine 9
Using the Telescopic Tube, ose & Attachments 10
Use and aintenance of Brushes and Heads 10
The Parquet Brush 10
The Kombi Nozzle 10
The Turbo Nozzle 10
Vacuum aintenance 11
Changing the Filter Bag 11
Changing the Exhaust Filter 11
Changing the Micro- ygiene Filter 11
Changing the AIRBELT 11
Clog Removal 12
Clogs in the ead or Brush 12
Clogs in the Telescopic Tube 12
Clogs in the ose 12
Clogs in Entrance to Filter Bag 12
Trouble-Shooting Guide 13
AIRBELT K2 Schematic and Part Numbers 14
AIRBELT K3 Schematic and Part Numbers 15
2
Vacuum motor 1250 watts (10.6 amps)
Water lift (at motor) 110 inches
Airflow (at motor) 120 CFM
Filter bag capacity .8 gallons
Sound level 63 dBA
Body weight 12 lbs
Motor protection thermal cut-out
Cord length 24.5 feet
Range 36.75 feet
Technical details may be subject to change.
TABLE OF CONTENTS
TECHNICAL DETAILS
To contact SEBO in the United States of America:
SEBO America, LLC
Telephone: [phone]
Fax: [phone]
Website: www.sebo.us
To contact SEBO in Canada:
Floor Care Equipment, Ltd.
Telephone: [phone]
Fax: [phone]
Website: www.sebocanada.ca
HOW TO CONTACT SEBO
For Warranty coverage information please refer to your Warranty Card included with your SEBO vacuum cleaner.

IM ORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS ACHINE
3
1. Do not leave vacuum while plugged in. Unplug from
outlet when not in use and before servicing.
2. Do not use outdoors or on wet surfaces.
3. Do not use near small children or pets. Do not allow to be
used as a toy. Use of this product by children should
always be supervised by an adult.
4. Use only as described in this manual. Use only
manufacturer-recommended attachments.
5. Do not use with a damaged cord or plug. If vacuum is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, take it to a SEBO service
center.
6. Do not pull or carry by cord, use cord as a handle, close a
door on cord, or pull cord around sharp edges or corners.
Do not run vacuum over cord. Keep cord away from heated
surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the
plug – not the cord.
8. Do not use outlets above counters to plug in vacuum –
damage to items in the surrounding area could occur.
9. Always carry the vacuum over steps and sills.
10. Do not handle plug or vacuum handle with wet hands.
11. Do not put any object into vacuum openings. Do not use
machine with any openings blocked. Keep openings free
of lint, hair, and anything that may reduce air flow.
12. Do not re-use filter bags or wash the filters.
13. Do not remove any screws from vacuum.
14. Do not vacuum up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
15. Do not use vacuum without filter bag and/or filters in place.
16. Turn off all machine controls before unplugging.
17. Use extra care when cleaning on stairs.
18. Do not use machine to vacuum up flammable or
combustible liquids such as gasoline or use in areas
where they may be present.
19. Machines can cause a fire when operated near flammable
vapors or materials. Do not operate this vacuum near
flammable fluids, dust or vapors.
20. Maintenance and repairs must be done by authorized
personnel.
21. Use only original SEBO replacement parts.
22. Do not use vacuum as a step.
23. If vacuum is used on plush carpet or carpet with thick
padding, do not leave machine standing in one place with
machine turned on.
24. While the vacuum is in use, the power cord should be
unwound from the cable reel at least two thirds of its length.
old plug when rewinding onto the cord reel. Do not allow
plug to whip while rewinding.
25. Keep hair, loose clothing, fingers, and all parts of body away
from vacuum openings and moving parts. Do not place
fingers or other body parts under vacuum unless it is
unplugged.
26. Do not place the power head over rug or carpet edges.
27. The vacuum has a manual reset thermal protector. The
protector is reset by switching off the vacuum. The thermal
protector needs some time to cool down after switching off!
Check the vacuum for air blockages or mechanical failures
before switching on.
28. Store the vacuum in a dry place at room temperature. When
the vacuum is not in use, you should rewind the cord onto
the cord reel
29. The K3 hose contains electrical wires. Do not use if
damaged, cut, or punctured. Avoid picking up sharp objects.
30. Always unplug vacuum before connecting or disconnecting
either hose or power head.
31. Use a SEBO power head only in combination with a SEBO
vacuum cleaner.
32. Do not connect power head to a malfunctioning or damaged
vacuum.
When using an electrical appliance, basic precautions must always be followed.
To reduce the risk of electric shock, this vacuum cleaner has a polarized plug; one blade is wider than
the other. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any
way. Connect only to the outlet type specified on the serial number plate underneath the machine.
SAVE THESE INSTRUCTIONS.
WARNING: To reduce the risk of fire, electric shock, or injury:
!

SEBO AIRBELT K RODUCT FEATURES
4
Bag Full or Clog Light & Auto Shut Off – A
warning light will illuminate and the
machine will automatically shut off, when it
senses a full bag, a clog in the airflow path-
way, or an excessively dirty micro filter.
If the
vacuum’s airflow pathway becomes restricted
due to a full bag or the existence of a clog, the amber “BAG FULL
OR CLOG” light (located on top of the canister near the ON/OFF
power control knob) will illuminate. If the user ignores this warn-
ing, the suction motor will heat up due to the lack of cooling pro-
vided by the airflow. Once the motor reaches a certain tempera-
ture it will shut off to protect itself from damage. The user should
turn the switch off, unplug the machine and immediately insert a
new bag or remove the clog (to remove a clog, refer to the Clog
Removal section on page 12). After approximately 30 minutes, the
motor will have cooled and the vacuum can be restarted. If the air-
flow is still restricted, the “BAG FULL OR CLOG” light will again
illuminate and the machine will shut off.
This feature prevents
damage to the motor due to overheating.
Shock Absorber Provides Furniture and
Wall Protection – The “AIRBELT” bumper
that surrounds the K canisters acts as a
protective barrier. The soft foam bumper
with its durable covering protects furniture,
walls and the vacuum itself from damage
during use.
Personalized Vacuums – AIRBELT canister vacuums can be
personalized with a replacement AIRBELT bumper cover avail-
able in eight patterns and colors.
Large Operating ange – A 36.75-foot operating range saves
time because it minimizes the number of electrical outlets
needed during use.
Quick-release Connections – The AIRBELT K models allow for
quick and convenient connection of telescopic tubes, power
brush heads, accessory cleaning heads and on-board tools.
Comfortable Ergonomic Handle – The AIRBELT handles are
ergonomically designed and positioned to reduce wrist and
arm fatigue. For extra comfort, an additional swivel is built into
the handle-to-hose connection.
Mid-sized Canister Vacuum – The SEBO AIRBELT K3 and K2
are considered mid-size canister vacuums, which means they
are machines medium in size that offer mid-sized, on-board
attachments and a mid-sized filter bag with a dirt capacity of .8
gallons. The K machines also weigh four pounds less than the
C machines.
ubber Coated Wheels and High Quality
Castors – The quality of the wheels and
castors on SEBO canisters prevent damage
to floors and rotate 360 0for easy maneu-
verability.
Three On-board Tools – The vacuum comes standard with a
crevice tool, dusting brush and upholstery nozzle. The dusting
brush is mounted on the telescopic tube, and the crevice and
upholstery nozzles are on the canister. Many optional acces-
sories are also available.
AI BELT K2: The SEBO AIRBELT K2 is a straight-suction vacu-
um. As a result, it differs from the AIRBELT K3 in the following
two ways:
Variable Power Control on Canister Body –
Because the AIRBELT K2 does not have an
electrified hose and telescopic tube, its
variable power control switch is located on
the canister body, not the handle.
Can Not Use a Power Brush – The AIRBELT K2 does not have
an electrified telescopic tube and hose; therefore, it does not
accommodate an electrified power brush. Instead, your K2
model comes standard with one or more of the following: a
Turbo Nozzle (an air-driven brush head) for cleaning rugs and
carpet; a Parquet Brush for cleaning hard floors; or a Kombi
Nozzle for rugs and carpet.
Turbo Nozzle Parquet Brush
AIRBELT K2
Kombi Nozzle
K2 Midnight Blue comes standard with the Kombi Nozzle.
K2 unter Green comes standard with the Turbo Nozzle and
the Parquet brush.
Crevice Nozzle
Dusting Brush
Upholstery Nozzle

5
Designed for All Floor Surfaces. AI BELT K3:
The AIRBELT K3 has an electrified hose and
telescopic tube designed to accommodate
the ET-1 power head. The ET-1 is designed
to provide thorough brushing for optimal
cleaning of carpets.
Both Carpet and Hard Floor Cleaning – With a power brush to
clean carpets and a parquet nozzle to clean hard floors, the
AIRBELT K3 provides all the flexibility needed to care for a vari-
ety of floor surfaces. The parquet nozzle comes standard.
High-quality Telescopic Tube and Hose – On the K3, the power
cord is built inside the telescopic tube and suction hose. This
eliminates unsightly external wires and enables unobstructed
and convenient handle height adjustment.
Variable Power Control on Handle – The
vacuum’s suction power can be adjusted
from 0 to 1,250 watts by a slider switch con-
veniently located on the handle.
Powerful Vacuum Motors Provide Excellent Cleaning – The
canister suction motor is 1,250 watts, and the power head
motor is 175 watts (ET-1), for a total of 1,425 watts.
AIRBELT K3
The SEBO ET-1 (12” wide, 10 1⁄2” cleaning
width) – This power head delivers cleaning
flexibility because its brush action aggres-
sively cleans carpeting, and the brush may
be switched off to clean hard floors and
delicate rugs. The steering ability of the
swivel neck helps to easily clean around obstacles, and its L-
shaped head provides maneuverability around furniture and
under cabinets. It also has brush height and brush wear warn-
ing lights.
Brush Obstruction Light & Auto Shut Off –
If an obstruction becomes jammed in the
brush roller, a warning light will quickly
flash, the brush roller will immediately stop
spinning and the vacuum will shut off.
The
user should turn the power switch off, unplug
the machine, and immediately remove the
obstruction. If the user restarts the machine without removing
the obstruction, the power head will again shut off and the amber
light will turn on.
This prevents the belt from breaking and pro-
tects the motor from damage.
Incorrect Height Setting or Brush
Deterioration Light – To ensure optimum
cleaning at all times, a warning light will
illuminate to indicate when the brush
height is set too high for effective cleaning,
or when the brush roller should be
replaced due to excessive wear.
In addition to the standard on-board tools, a variety of optional
attachments are available. The nine-foot extension hose
(extends suction hoses) and the 20-inch extension tube are very
popular because they create useful tools for cleaning stairs and
out-of-reach areas. These two items are sold separately or as
part of multiple item attachment kits. Another popular attach-
ment is the hand held turbo brush for removing pet hair from
upholstery.
K Service Box
Part #6695AM
20-inch Extension Tube
Part #1084 G
9-foot Extension ose
Part #1495AM
K Filter Bags
Part #6629AM
SEBO filter bags can be purchased in boxes of eight and filters
are sold separately. Also, bags and filters can be purchased
together in model-specific kits called “Service Boxes.” SEBO
bags, filters and accessories are reasonably priced and widely
available.
To create a fresh scent while vacuuming, “SEBO FRES ” is
available. To use, deposit a scented stick in the filter bag.
SEBO FRES
Part #0496AM
O TIONAL ATTACHMENTS, ACCESSORIES, BAGS & FILTERS
Kombi Nozzle
Part #7260GS
Wall & Floor Brush
Part #1325 G
Flat Upholstery
Nozzle
Part #1090 G
and-held Turbo
Brush
Part #6179DA
Radiator Brush
Part #1496GS
Premium Parquet Nozzle
Part #7200GS
Turbo Nozzle
Part #6780ER
EPA
Service Box
Part #6431ER
AIRBELT
Available in
several colors
and patterns
Part #6047AM/01-08
Filter Box
Part # 6696AM
Parquet Brush
Part #6391DA

6
STANDARD FEATURES OF ALL SEBO VACUUMS
Designed and anufactured in Germany – Legendary quality,
reliability and performance make SEBO vacuums the choice of
cleaning professionals throughout the world.
Excellent for Users With Allergies or Asthma – The British
Allergy Foundation recommends SEBO filters.
Tightly Sealed Vacuums Ensure Effective Filtration – Dirty air,
which flows through a vacuum, can only be filtered completely
if it does not escape into the room through seams or seals in
the machine. This is why all SEBO vacuums have tight seals
throughout. Many vacuum companies with high-filtration
claims are actually quoting specifications made by the manu-
facturer of the filter material, as measured in the laboratory,
not the filtration effectiveness of the vacuum itself while oper-
ating. Whether or not dirty air can escape through leaks in the
body of the machine is not considered. The filtration effective-
ness of SEBO vacuums is tested while they operate.
Save oney! SEBO Vacuums Last for Years and Extend Carpet
Life! – If properly maintained, SEBO vacuums save ordinary
residential users hundreds of dollars by providing excellent
performance for ten to fifteen years or more, and their deep-
cleaning power-brush technology extends the life of carpets.
Typical vacuums perform poorly, even when new, and usually
do not last beyond two years. So six or seven “disposable vacu-
ums” must be purchased during the average life expectancy of
just one SEBO machine.
Outstanding Warranty Coverage – SEBO is confident about the
quality of all its vacuums. Therefore, all models include a five-
year warranty on the motor and all non-wear parts. Please
refer to the Warranty Card included with your SEBO vacuum
cleaner for complete warranty coverage information.
SEBO icrofilters Ensure Continuously Strong Suction
Performance – They are also long lasting, inexpensive and easy
to change in seconds.
Changing Bags is Easy and Clean – SEBO filter
bags can be changed in just a few seconds, and a
cap keeps dust sealed inside during removal and
disposal.
Effective Pet Hair Removal – All SEBO vacuums
easily remove pet hair!
SEBO’s FILTRATION SYSTE :
Bags are Better! – Top-fill, three and four-
layer bags are an integral part of SEBO’s filtra-
tion system because they hold virtually all dirt
captured by the vacuum, which improves the
effectiveness and useful life of the microfilters.
They also ensure continuously strong suction
because dirt enters from the top, deposits at
the bottom, accumulates upward, and air exits through the sides,
which allows unimpeded airflow as they fill to capacity. And they
can be sealed when full, so no dust can escape into the air during
bag removal and disposal.
In contrast, without bags to hold nearly all the
captured dirt, the microfilters on bagless vac-
uums quickly clog from excessive dirt build-
up and must be replaced often, or a loss of
suction and cleaning effectiveness will occur.
In addition, dust and other allergens become
airborne when emptying bagless dirt contain-
ers. Lastly, bagless vacuum microfilters are expensive, usually
costing more than a multi-year supply of SEBO filter bags.
S-class Pre-motor Microfilters – S-class
Pre-motor Microfilters (S =“Schwebstoff” =
airborne particles) are made from electrosta-
tically charged micro-fiber material, which
attracts and captures dust particles from the
airflow of the vacuum before it passes over
the motor to cool it. Cooling the motor with
super-clean air increases motor life and
reduces the possibility of maintenance, even
after many years of use. This means that
exhaust air is cleaned to the highest level. The
S-class Standard requires filters to absorb
greater than 99.9% of particles down to 0.3 microns in diameter.
For comparison, 100 microns is the diameter of a human hair.
Their advantages are a relatively open texture that allows
smoother airflow for better suction performance, a longer life
expectancy, and they cost less than EPA filters
HEPA Pre-motor icrofilters (Optional) – EPA Pre-motor
Microfilters (“ igh Efficiency Particulate Air”) remove a mini-
mum of 99.97% of all airborne particulate matter down to 0.3
microns in diameter. Because these filters use small grid-like
structures to capture dust particles, dirt build-up clogs the air-
flow pathway sooner than what is expected from S-class micro-
filters. owever, SEBO’s EPA microfilters are sold along with
four-layer “Ultra-bags,” which provide highly effective filtration
before the airflow goes through the EPA microfilter, greatly
increasing life expectancy and reducing the potential of dimin-
ished air flow.
Exhaust Filters – Exhaust fil-
ters clean the air emitted by
the vacuum motor.
S
u
p
e
r
q
u
i
e
t
a
i
r
e
x
h
a
u
s
t
a
l
l
a
r
o
u
n
d
!

7
IDENTIFICATION OF ARTS
14. Exhaust filter cover
15. AIRBELT shock absorber
16. Carrying handle
17. Suction opening
18. ose release button (K3 only)
19. ose neck
20. Crevice nozzle
21. Parking attachment holder
22. Power cable shroud
23. AIRBELT clip
24. Parking attachment holder
25. Filter bag cover release catch
26. Filter bag cover
Push the neck (19) of the hose (13) into the suction opening of the canister (17). K3: The notch in the
suction opening will line up with the raised bar on the neck. When the notches are lined up cor-
rectly, the neck will snap firmly into place. To release the hose from the suction opening, press
the release tab (18) on the neck of the hose (19), and pull the neck out. K2: To release the hose
from the suction opening, squeeze the tabs (37) on the retaining ring and pull the neck out.
Attach the short mains cable (12 - K3 only) on the underside of the handle by connecting one
cable plug where the hose connects to the handle and the other where the handle connects to the
telescopic tube.
Connect the handle (1) to the top of the telescopic tube (4). Snap in place. To release the telescopic tube
(4) from the handle, push the handle release button (3) and slide the handle out.
Attach the head or brush to the bottom of the telescopic tube (4). Insert the bottom of the telescopic tube
into the neck of the head or brush (38) until it locks into place; or line up the square hole in the telescopic
tube with the notches in the front of the neck, and snap firmly into place. To release a head or brush from
the telescopic tube (4), push the release button (7), and pull the head or brush tool off the end of the tel-
escopic tool. The release button (7) is in the same position on all of the heads, brushes and power heads.
To attach the dusting brush clip (27), locate the two raised ridges on the upper end of the telescopic tube
(4) just below the handle. Push the clip onto the tube directly below the ridges then slide the clip up until
it locks onto the ridges. Snap the dusting brush (28) into the holder.
NOTE: To attach the ET-1 power head to your K3 canister, please refer to your power head owner’s
manual for instructions. Attaching incorrectly could cause damage.
Brushes and Heads
29. Parquet brush - standard for the K3 Volcano,
Red and Onyx and K2 unter Green.
Optional for the K2 Midnight Blue -
Part #6391DA
30. Kombi nozzle - standard for the
K2 Midnight Blue.
Optional for the K3 Volcano,
Red & Onyx and K2 unter Green -
Part #7260GS
31. Turbo nozzle - standard for the
K2 unter Green.
Optional for the K3 Volcano, Red and Onyx
and K2 Midnight Blue -
Part #6780ER
32. ET-1 Power ead - standard for all K3s
20. Crevice nozzle
11. Upholstery nozzle
NOTE: All illustrations shown in this manual represent the K3 model except where part numbers and instructions are different for each model.
1
2
3
4
5
6
7
31
18
30
ASSEMBLY
32
1. andle grip
2. Power control slider (K3 only)
3. andle release button
4. Telescopic tube
5. Slide button
6. Power cable
7. Tool release button
8. Kombi nozzle
9. On/Off power control knob
10. Warning light
11. Upholstery Nozzle
12. Mains cable (K3 only)
13. ose
19
9
10
11
13
14
17
16
12
15
8
20 21 22
15 23
24 25
26
11
28
20
27
27. Dusting brush clip
28. Dusting brush
19
17 18
19
17
37
1
4
3
4
38
7
K3
K2
Standard Attachments
29

8
O ERATING INSTRUCTIONS ALL K VACUUMS
Starting The achine - Figures 1, 2 & 3
Before turning on your canister, make sure that you have a firm hold on the handle grip to keep the
machine from moving forward.
1. With the canister main power control knob (9) in the OFF position, grasp the plug and pull the
power cord (6) out from the power cable recess (22). The power cord (6) should be unwound
from the cable reel at least two thirds of its length. Note: do not over-extend the cord.
2. Plug the polarized power cord into a 120 volt wall outlet located near the floor.
3. Press the main power control knob on the base of the canister (9) gently with your foot or
hand. The green light (10) will illuminate indicating that the power is on (K3 model only).
Operating the achine - Figures 4, 5, 6 & 7
Adjust the telescopic tube (4) to the correct height by pushing the slide button (5) and gen-
tly pulling the tube out to lengthen, or pushing it in to shorten. Release the slide button
(5) to lock the tube to the adjusted height.
When changing heads, always switch the vacuum off with the power control knob (9), and
then unplug the power cord.
The “bag full or clog” light (#10, figure 2) works correctly only at full power. At lower power
levels, the “bag full or clog” light may illuminate incorrectly. Check the status of the filter
bag regularly at full power. If the light remains illuminated at full power, and the filter bag
is not full, check for clogs (see page 12).
To retract the cord, switch the vacuum off, unplug it from the outlet, then gently pull on
the cord near the plug recess (22) and the mechanism will automatically rewind. Before
rewinding the cable, always switch off and unplug the vacuum. old the plug while
rewinding the cord onto the cord reel. Avoid letting the plug whip while rewinding.
WARNING! The quality, condition, coating, texture, age and manufacturing technique of all floor surfaces vary.
Therefore, vacuums with rotating brushes, including your SEBO, may damage some floor coverings or surfaces. Some types
of high-gloss hardwood floors, cushion vinyl, berber carpets, long shag, and delicate or hand-woven carpets are particularly vul-
nerable to damage by rotating brushes. When possible, consult the materials supplied by your flooring manufacturer for infor-
mation on proper upkeep and cleaning. To ensure that your new SEBO vacuum cleaner is compatible with your floor, please
test the vacuum cleaner on each type of flooring surface in a small inconspicuous area to determine if any damage occurs.
If damage occurs, stop using the vacuum cleaner immediately!
!
Figure 4
Suction Control - Figure 3
K2 users: the suction control dial is located on the top side of the canister on the power control knob
(9). Rotate the dial counter-clockwise for maximum suction. Rotate clockwise to reduce suction for
vacuuming curtains or delicate fabrics.
K3 users: for information on suction control, refer to page 9 of this manual.
4
5
Figure 1
22
6
Figure 2 - K3
Figure 3 - K2
9
9
10
Figure 7
21
Figure 6
24
Figure 5
39
The vacuum can be stored with the canister in a hori-
zontal or vertical position. The Parquet brush, Kombi
nozzle and Turbo nozzle have a parking tab located on
the front of the neck (39). Insert the parking tab into the
upper side of the parking groove and slide down firmly.
For vertical storage, or for easy carrying, use the park-
ing slot on the underside (24). For horizontal storage,
use the parking slot on the end of the canister (21).

9
Starting The achine and Suction Control -
Figures 1, 2, 8, 9 & 10
Before turning on your canister, make sure that the vacuum handle is in its upright
locked position (figure 8).
1. With the canister main power control knob (9) in the OFF position, and the power
control slider on the handle (#2, figure 9) in the OFF position, pull the power cord
out from the base of the canister (figure 1). The power cord should be unwound from
the cable reel at least two thirds of its length. Note: do not over-extend the cord.
2. Plug the polarized power cord into a 120 volt wall outlet located near the floor.
3. Press the main power control knob (9) on the base of the canister gently with your
foot or hand. The green light (10) will illuminate indicating that the power is on
(figure 2).
4. Slide the Power Control Slider (#2, figure 9) toward the MAX position. It will move
freely between 0 suction and MAX suction. Set the slider to the suction desired.
Release the foot pedal (#41, figure 10) on the ET-1 power head.
0 = Zero Suction
MAX = Maximum Suction
ON position - Move the slider toward MAX.
OFF position - Pull the slider up to 0 suc-
tion then continue pulling the slider up
until it “clicks” into the OFF position.
Operating The achine - Figure 10
When the power head is on with the handle in the upright locked position (see
figure 8 above), the brush roller will not spin.
To release the ET-1 power head from the upright locked position, press down on
the foot pedal, (#41, figure 10) lower the handle into the normal operating posi-
tion and push the button on the top of the power head (#40, figure 8) to engage
the brush roller. The green light on the power head will illuminate.
The handle can be lowered to a horizontal position useful for vacuuming under
beds.
You may adjust the suction control with the power control slider (2) as you vac-
uum different surfaces or when using the accessory tools. For optimal cleaning
and brushing, operate the machine at the maximum suction power setting and
push the power head slowly over the carpet.
When the canister’s main power control knob is in the ON position, you may turn
the power head off and on with the power control slider (2). To turn the power
head off using the power control slider, pull the slider to 0 suction, then contin-
ue pulling the slider up until it “clicks” into the OFF position. The green power
head light will then shut off (the green light on the canister (10) will remain illu-
minated until the vacuum is powered off using the main power control knob).
Always turn the power off on both the canister and the power head when
changing heads or unplugging the vacuum. Slide the power control slider on
the handle to its OFF position, press the power control knob on the base of the
canister (9) gently with your foot or hand, then unplug the canister to complete-
ly shut down the power when changing heads or storing the vacuum.
To retract the cord, switch the vacuum off, unplug it from the outlet, then gen-
tly pull on the cord near the plug recess (22) and the mechanism will automat-
ically rewind. Before rewinding the cable, always switch off and unplug the vac-
uum. old the plug while rewinding the cord onto the cord reel. Avoid letting the
plug whip while rewinding.
Please refer to your ET-1 power head owner’s manual for more information
ET-1 power head
ADDITIONAL O ERATING INSTRUCTIONS FOR K3 WITH OWER HEAD
Figure 10
Figure 8
Figure 9
2
41
40

10
To remove a brush or power head, switch off the power and unplug the vacuum. Then,
press the tool release button (7) and pull the tube out.
NOTE! K3 users with the ET-1 power head, please refer to your power head user’s manu-
al for more detailed instructions for operating and maintaining your power head.
Parquet brush - Figure 13
The Parquet brush (29) is specially designed for use on hard surfaces. It is lightweight with
soft bristles, so it glides gently over floors and provides easy maneuverability. Fibers and
hair can be pulled out of the bristles manually, or vacuum the bristles with the telescopic
tube.
Kombi - Figure 14
The Kombi nozzle (30) is adjustable for carpet or hard floors. To set for carpet, slide the up
arrow button (42) to the right until it clicks into place. The hard floor dusting brush will raise
up allowing the head to move over the carpet. To set for hard floors, slide the down arrow
button (43) to the left until it clicks into place. The brush will lower to gently sweep your
floors. The slider in Figure 14 is set in the position for hard floors. The brush should be
cleaned regularly. Remove the Kombi nozzle from the telescopic tube to clean. Fibers and
hair can be pulled out of the bristles manually, or vacuum the bristles with the telescopic
tube. The brush strip is removable for cleaning and replacement.
Turbo Nozzle - Figure 15
The Turbo nozzle (31) has an air-driven rotating brush for gentle brushing of carpets. The
Turbo nozzle can be adjusted for high and low pile carpet. To adjust the head for high pile
carpet, push the slider button (44) to the right. For low pile carpet, push the slider button
(44) to the left. The slider in Figure 15 is set in the low pile position. The rotating brush
should be cleaned regularly. Remove the Turbo nozzle from the telescopic tube to clean.
Remove fibers and hair from the brush manually.
The telescopic tube (4) is useful for vacuuming corners and hard-to-reach areas. You may
use the telescopic tube without a brush, power head or attachment. To remove a brush or
power head, switch off the power control knob (9) and unplug the vacuum. Then, press the
tool release button (7) and pull the tube out. The crevice nozzle (20) and dusting brush (28)
may be inserted onto the end of the tube. To use the upholstery nozzle (11), fit it onto the end
of the crevice nozzle (20). It is not necessary to turn off the vacuum while switching the stan-
dard attachments (the crevice nozzle, upholstery nozzle or dusting brush). After use, switch
off the power, unplug the vacuum and remove attachment. Re-insert the telescopic tube into
the power head or brush, turning the tube if needed, until you hear it click into place.
NOTE! K3 users with ET-1 power head, please refer to your power head user’s manual for
more detailed instructions for connecting your power head.
To use the hose without the telescopic tube, switch off the power and unplug the vacuum.
Push the handle release button (3) and pull the ANDLE out of the end of the telescopic tube.
Do not try to separate the hose from the handle! Insert the crevice nozzle (20) or dusting brush
(28) onto the end of the handle. To use the upholstery nozzle (11), fit it onto the end of the
crevice nozzle (20). After use, switch off the power, unplug the vacuum and remove the
attachment. Re-insert the handle into the telescopic tube making sure it is seated correct-
ly and snap it into place.
Figure 11
Figure 12
7
Using the Telescopic Tube, Hose & Attachments - Figures 11 & 12
4
Figure 13
Figure 15
Figure 14
43
Always unplug vacuum from outlet before dismantling
any part of machine!
!
USE AND MAINTENANCE OF BRUSHES AND HEADS
42
44
L
L
20
1
4
20
11
29
30
L
L
31

11
VACUUM MAINTENANCE
Changing the Filter Bag - Figure 16
To change the filter bag (45), set the canister upright (as shown in figure 13),
press the cover release catch (25) and lower the filter bag cover (26). Grasp
the green filter bag sealing plate (46), slide the plate from the holder (48) and
push the filter bag cap (47) on to seal the bag. Slide the sealing plate (46) of
a new bag into the bag holder slots (48) and push it in firmly until it locks into
place. Close the cover, making sure it snaps shut completely. You may find it
convenient to store the bag cap inside the filter bag housing below the filter
bag. Do not re-use the filter bags. Note: the nature of the contents of the fil-
ter bag will affect the point at which it needs changing. Fine dust may require
an earlier change even though the bag is not full. Fluff or hair allows air to
pass through easily, so the filter bag may overfill before the amber “bag full”
light illuminates.
The “bag full or clog” light works correctly only at full power. At lower power
levels, the “bag full or clog” light may illuminate incorrectly. Check the status
of the filter bag regularly at full power.
Changing the Exhaust Filter - Figure 17
The exhaust filter (51) needs to be changed when it becomes extremely dirty
or clogged with dust, or after approximately 10 to 20 filter bags have been
used. To change the exhaust filter, set the canister flat on the floor as shown
in figure 17. Remove the printed cover on top of the machine (14) by lifting the
catch (49) in the upholstery nozzle recess (see inset, figure 17). Pull out the
filter using the handle (50) and fit the new filter into the same position. The
filter handle should point toward the upholstery nozzle when it is folded
down. Fit the tabs on the bottom of the cover (14) into the grooves and snap
the cover down firmly.
Figure 16
Figure 18
Figure 19
Always unplug vacuum from outlet
before dismantling any part of machine!
!
K Filter Set:
Exhaust Filter
and
Micro- ygiene
Filter
Part #6696AM
Changing the AIRBELT - Figure 19
If damage occurs to the AIRBELT cover, it will need to be replaced. To remove
the AIRBELT (15), pry off the clip (55) by inserting the tip of a slot-head screw-
driver under the bottom side of the clip. Push downward on the screwdriver
until the clip pops off. Grasp the end of the AIRBELT cover and pull - the AIR-
BELT cover will peel off. The foam bumper (54) remains on the vacuum. To
replace the AIRBELT, insert the side ribs of the AIRBELT into the grooves (56).
Start at the back, insert rib into one groove (56), and while holding it down,
stretch the AIRBELT cover around the foam (54) into the opposite groove (56).
Continue around the vacuum. Secure the ends with the clip (55).
SEBO AIRBELT covers are available in a variety of colors and patterns. See
your SEBO dealer for available selection.
Changing the icro-Hygiene Filter - Figures 16 &18
After 10 to 20 bags have been used, change the micro-hygiene filter (52). To
remove the micro-hygiene filter, set the canister upright (as shown in figure
16). Press the cover release catch (25) and lower the filter bag cover (26).
Remove the filter bag, then remove the cover by sliding it up and out of the
grooves (53). Pull the old filter out (52) and slide the new filter into the same
position. Replace the filter bag, then re-insert the cover by fitting the tabs
into the grooves (53) on both sides and sliding it in and down. Push the cover
closed, making sure it snaps shut completely.
25
Note: Never operate the vacuum with incorrectly attached filters or without filters, bag,
AIRBELT or filter bag housing cover (26). Do not re-use filter bags. Do not wash and re-use filters.
Filter Bags
Part #6629AM
AIRBELT Cover - Part #6047AM/01-08
Figure 17
54
15
55
56
54
56
26
45
26
26
25
48
45
46
47
49
14 50
51
51
52
52
5353
K Service Box - 8 Filter Bags, Exhaust Filter and
Micro- ygiene Filter Part #6695AM

CLOG REMOVAL
12
NOTE! K3 users with ET-1 power heads, please refer to your power head user’s
manual for more detailed instructions for removing clogs in your power head.
If the “bag full or clog” warning light (10) remains illuminated after the filter bag
has been changed and the filters are in good condition, there is likely a clog in the
system.
Clogs in the Head or Brush - Figure 20
Clogs in the swivel neck (57) of a head or brush can be cleared by first pressing the
tool release button (7) and removing the brush or head. Check inside the swivel neck
channel (56), and clean out pathway.
Clogs in the Telescopic Tube - Figure 20
Remove head from telescopic tube (4) by pushing the tool release button (7) and
pulling the tube out. Remove the hose from the top of the telescopic tube by pushing
the handle release button (3). A stiff wire or stick can be used to push the clog out of
the tube.
Clogs in the Hose - Figures 21, 22 & 23
Check for suction at the end of the hose (19). If you feel reduced suction, the blockage
is in the hose. To clear blockages in the hose (13), remove the telescopic tube (4) by
pushing the tool release button (7) and pulling the tube out. old the hose upright with
one hand blocking the top and switch on the machine. If necessary, quickly lift your
hand on and off the end of the hose. If that does not clear the clog, you may also clear
clogs by reversing the hose. K3: After removing the telescopic tube, push the release
button (18) on the hose neck (6) and remove the hose from the machine.
K2: After removing the telescopic tube, squeeze the tabs (37) on the retaining ring and
pull the hose neck out.
Remove the hose handle (1) from the telescopic tube by pressing the handle release
button (2). Insert the handle end of the hose (1) into the suction opening (17). old the
hose upright with one hand blocking the top and switch on the machine. If necessary,
quickly lift your hand on and off the end of the hose.
Note: Do not insert a wire or stick into the hose. Doing so may cause damage to the
hose.
Clogs in Entrance to Filter Bag - Figure 21
Remove hose (10) from vacuum cleaner (see figure 21), open the filter bag cover and
remove the filter bag. (figure 16, page 9). Clean out entrance to bag (58).
Figure 21
Always unplug vacuum from outlet before removing
any clogs!
!
Figure 24
19
K2
Figure 20
57
7
4
3
Figure 22
Figure 23
18
19
37
37
K3
1
21
13
13
17
58

TROUBLE-SHOOTING GUIDE
13
PROBLE
Does not turn on
Bag full or clog light on
Bag full or clog light on
& machine shuts off
Does not pick up
Filter bag door won’t
fully close
REASON
1. Telescopic tube not inserted properly.
2. Not plugged into working outlet.
3. Cable worn.
4. K3: The power control slider
switch is set to “0” (“off” position).
1. Bag full.
2. Clog in hose, telescopic tube,
brush or head, or entrance to
filter bag.
3. Micro-hygiene filter dirty.
4. Exhaust filter dirty.
1. ose/handle assembly not
correctly inserted.
2. The suction control dial is rotated
to no suction setting
3. Filter bag cover not closed.
1. Filter bag cover not fully closed.
2. Bag not inserted properly
3. Micro-hygiene filter not properly
inserted.
SOLUTION
1. See page 7.
2. Use another outlet.
3. Replace cable.
4. K3: Set slider switch to “on”
position. See page 9.
1. Replace filter bag. See page 11.
2. See Clog Removal on page 12.
K3 users with clog in power head
attachment: refer to clog removal
in the ET-1 owner ’s manual.
3. Replace micro-hygiene filter.
See page 11.
4. Replace exhaust filter. See page 11.
1. Re-insert hose/handle assembly
making sure that it is lined up
properly and is snapped into
place. See page 7.
2. K2: Rotate suction control
dial to yellow setting. See page 8.
3. See below.
1. Re-insert bag. Lock the cover
down firmly.
2. Re-insert bag. Lock the cover
down firmly.
3. Remove the filter bag cover (26) and
make sure the micro-hygiene filter
housing is seated firmly in place
(see pg. 11, figure 18).
Always unplug vacuum from outlet before dismantling any part of the machine!
!

14
AIRBELT K2 SCHEMATIC AND ARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
21
22
24
25
26
27
28
29
30
31
32
33
34
34
35
36
38
39
40
41
42
43
44
45
46
6754GS
6675GS
6014
6042WS
6681 G
6696AM
6756GS
6607GS
6629AM
6752GS
665603E
6621
1739
6641ER
6638
6631ER
6679GS
6622GS
6680G2
6625ER
6427K2
60613LG
6086 G
6623UL
6047AM/08
6048GS
6627GS
1092GS
6300GS
6303GS
6447GS
6271GS
0105
6421GS
6420GS
6694GS
6612GS
1387GS
6751GS
6780ER
6391DA
Bottom casing w/castors (44)
Suction neck - K2
Seal
Spring lock
Bag holder, complete
KMicrofilter & Exhaust set
Bag cover w/castor (10)
Cover release
Filter bag SEBO K
Castor for bag cover
Cord reel w/lever & leaf spring (12&13)
Switch lever w/leaf spring (13)
Leaf spring
Electronic controller K2 w/switch
Internal cable - white
Vac motor 1250W includes motor
mount, adaptor, internal cable
w/thermal cut-off
Motor cover
Plug surround
Top casing - hunter green (25)
Release button w/screw
Exhaust filter cover - hunter green
On/Off knob for K2 hunter green
Casing clip
Foam bumper - K
AIRBELT textile-citrus (incl. pos. 31)
AIRBELT clip
Upholstery nozzle - K series
Crevice nozzle
andle grip K2, cpl. (incl. pos. 34A)
Retaining ring
7’ hose w/couplings & handle K2
(34&34a)
Telescoping Tube (39&40)
Screw 3.9 x 19
Slider button w/hardware
Release button w/leaf spring & cap
Clip for attachments
Retaining ring
Dusting brush
Castor for bottom casing
Turbo nozzle
Parquet nozzle
#9696A K2 Hunter Green achine
Pos. Part # Description
Canister with Handle/Hose
37
45 46
Turbo Nozzle
standard with
K2 unter Green
Parquet Brush
standard with
K2 unter Green
Kombi Nozzle
standard with
K2 Midnight Blue
# 9679AM K2 - Midnight Blue
# 9696AM K2 - unter Green
#9679A K2 idnight Blue achine Exceptions
24 6680DB1 Top Casing, K2 midnight blue (25)
26 6424AM Exhaust filter cover - midnight blue
27 60613GW On/Off knob - K2 midnight blue
30 6047AM/01 AIRBELT textile - dark gray
(incl. pos. 31)
37 7260GS Kombi nozzle
A

15
AIRBELT K3 SCHEMATIC AND ARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
21
22
24
25
26
27
28
29
30
31
32
33
34
36
37
38
39
40
41
42
43
44
6754GS
6677GS
6014
6042WS
6681 G
6696AM
6756GS
6607GS
6629AM
6752GS
665603E
6621
1739
6645ER
6638
6631ER
6679GS
6622GS
6680DR1
6625ER
6404K3
60666GW
6086 G
6623UL
6047AM/01
6048GS
6627GS
1092GS
6349AM
6270GS
6391DA
6421GS
6420GS
1387GS
6694GS
6369GS
0105
6751GS
Bottom casing w/castors (44)
Suction neck - K3
Seal
Spring lock
Bag holder, cpl.
KMicrofilter & Exhaust set
Bag cover w/castor (10)
Cover release
Filter bag SEBO K
Castor for bag cover
Cord reel w/lever & leaf spring
(12&13)
Switch lever w/leaf spring (13)
Leaf spring
Electronic controller K3 w/switch
Internal cable - white
Vac motor 1250W includes motor
mount, adaptor, internal cable
w/thermal cut-off
Motor cover
Plug surround
Top casing K - red (25)
Release button w/screw
Exhaust filter cover - red
On/Off knob for K3 red and black
Casing clip
Foam bumper - K
AIRBELT textile - dark gray
(incl. pos. 31)
AIRBELT clip
Upholstery nozzle - K Series
Crevice nozzle
7’ hose w/couplings & handle K3
Telescoping tube (38&39)
Parquet brush
Slider button w/hardware
Release button w/leaf spring & cap
Dusting Brush
Clip for attachments
Mains cable
Screw 3.9 x 19
Castor for bottom casing
#9687A K3 Red achine
Pos. Part # Description
37
Parquet Brush standard
with
K3 Red, Volcano and Onyx
#9689A K3 Volcano achine Exceptions
24 6680SR1 Top Casing, K - volcano (25)
26 6439AM Exhaust filter cover - volcano
27 60666VO On/Off knob for K3 volcano
30 6047AM/03 AIRBELT textile - volcano
#9688A K3 Onyx achine Exceptions
24 6680SW1 Top Casing, K - black (25)
26 6622AM Exhaust filter cover - black
30 6047AM/07 AIRBELT textile - silver/black
(incl. pos. 31)
Canister with Handle/Hose
#9687AM K3 - Red
#9689AM K3 - Volcano
#9688AM K3 - Onyx

16