Securam SafeLogic BackLit EC-0601A-BL Series User manual

1
Doc.No.:BLU-EC0601ABL130402
Version No.: V1.01 USER
SafeLogic BackLit Operating Instructions
This manual is for the SafeLogic BackLit EC-0601A-BL series EntryPad used in conjunction with
EL-0601, EL-0701, EL-0801 or EL-0901 lock bodies.
Important:
●For indoor use only.
●Battery Low Voltage: 5.2 ± 0.2V. The display will alert low battery when battery voltage
reaches 5.2±0.2V. PLEASE REPLACE THE BATTERY IMMEDIATELY.
Battery Replacement Instructions
a) In the back of Entry Pad you will see one 9 V alkaline battery. Take the battery out of
the battery compartment. Gently pull on the battery until it drops out.
b) Gently remove the connector by unsnapping it from the two terminals on the top of the
battery.
Never Pull on the Battery Leads
c) Connect a new 9V Alkaline battery to the battery clip.
d) Put the battery and the leads completely back into the battery compartment.
FEATURES:
1. Manufacturer default code is 1-2-3-4-5-6

2
2. Function of Code
a. Unlock safe lock system
b. Change code
3. Backlight Button Features
a) The middle of the “ ” button is raised for easier navigation in the dark. Press “ ” or
any other button and the backlighting will be switched on.
b) Pressing the “ ” button also clears any digits that have been entered in the current step
when programming or entering a code. For example, if you enter 6-5-4-3-2 to unlock the
safe but your code is 1-2-3-4-5-6 you just press and the code can be entered again
from the beginning.
4. Wrong Entry Penalty (Penalty Time)
Entry of four (4) consecutive invalid codes results in a 5-minute penalty time period.
a) The unit beeps at 5 second intervals indicating that it is still in the penalty time period.
b) While the system is in penalty time, the EntryPad buttons remain unresponsive. Pressing
buttons during penalty will not restart or lengthen the penalty time period. It will continue
to count through the 5 minute penalty time period.
c) While the system is in penalty time, removal of the batteries will interrupt the penalty time
countdown. Upon reinstallation of the batteries, the EntryPad continues to count down
until the 5 minute penalty time period expires.
5. Standby Status
In order to conserve battery power, the system will revert to standby status if there is no key
press within 10 seconds. Standby status is indicated by two short beeps.
6. Automatic Re-lock
The safe lock system automatically relocks after 6 seconds of being opened by a valid
code.
7. Low Battery Alert
a) Repeated beeping (8 beeps) during an unlock operation indicates that the battery is
low and needs immediate replacement.

3
b) Manufacturer recommends the use of 9-Volt standard alkaline batteries (Duracell or
Energizer brands are recommend) replaced annually.
USER PROGRAMMING INSTRUCTIONS
1. ALWAYS PERFORM OPERATIONS WITH THE SAFE LOCK SYSTEM UNLOCK AND
THE SAFE DOOR OPEN.
2. Before closing the door, make sure all the program changes are correct.
3. The system will not allow the User Code to be set to six zeros.
1. To Change Code
a) Enter “0” six times. Two beeps will sound, indicating the entry is valid and the system is
awaiting the code change.
b) Next, enter the existing six (6) digit code. Two beeps will sound, indicating the entry is valid.
c) Enter the new six (6) digit code. One beep will sound, indicating the entry is valid.
d) Re-enter the new six (6) digit code. One beep will sound, indicating the codes entered in
steps c and d are the same and the code changing process is successful.
e) If Three Beeps sound, the code change process has been unsuccessful. The existing code
is still valid. Repeat steps a to d.
Note:
a) Verify the new code at least 3 times before closing the door to make sure the code has
been programmed correctly.
b) The system will revert to standby status if there is no key press within 10 seconds.
Standby status is indicated by two short beeps.
Specifications：
Power Supply: DC 9V
Power Supply Range: DC 4.5V-12V
Standby Current : <50μA
Active Current: <20mA

4
Battery Low Voltage: 5.2±0.2V
Working Temperature: 0 ~ +49
Working Humidity (max): <90%
Code Length: 6 Digits Mechanical
System Life Span:
>10,000 Cycles (UL requirement)
>100,000 Cycles (SecuRam design criteria)
SecuRam Systems Inc. U.S.A.