Securitytronix ST-PTZIR530-36 User manual

V1.0 12/15/11
INSTALLATION MANUAL
ST-PTZIR530-36
IP66 Rated High-Speed Intelligent Dome
PTZ IR Color Camera
Copyright North American Cable Equipment, Inc.

v1.0 12/15/11
2
TABLE&OF&CONTENTS&
&
PACKAGE'CONTENTS ................................................................................................................... 3!
PRODUCT'DESCRIPTION............................................................................................................. 3!
SPECIFICATIONS............................................................................................................................ 3!
INSTALLATION'AND'OPERATION ............................................................................................ 4!
1.!UNPACKING'and'HANDLING........................................................................................................ 4!
2.!MECHANICAL'INSPECTION........................................................................................................... 4!
3.!SPECIAL'ATTENTION ..................................................................................................................... 4!
4.!CAMERA'SETUP................................................................................................................................ 5!
Protocol Set Up................................................................................................................................................... 5!
Camera Address Set Up................................................................................................................................ 6!
5.!PHYSICAL'INSTALLATION ............................................................................................................ 6!
6.!FUNCTIONS'and'OPERATION ...................................................................................................... 9!
System Information........................................................................................................................................10!
Display ....................................................................................................................................................................10!
Dome Settings ...................................................................................................................................................12!
Camera Setup.....................................................................................................................................................20!
Operation Setup................................................................................................................................................22!
Restart.....................................................................................................................................................................26!
Factory Defaults ...............................................................................................................................................27!
Help...........................................................................................................................................................................27!
7.!TROUBLESHOOTING ....................................................................................................................28!
APPENDIX'A ..................................................................................................................................29!
&

v1.0 12/15/11
3
PACKAGE&CONTENTS&
This package contains:
One ST-PTZIR530-36 high-speed intelligent dome color camera.
One mounting bracket with mounting hardware.
One installation manual.
PRODUCT&DESCRIPTION&
The ST-PTZ530-36 is an IP66 rated professional grade intelligent dome color camera with
pan, tilt and zoom (PTZ) capability of 530TVL using a 3.4mm to 122.4mm F1.6-F4.5 zoom
lens. This camera is capable of 360°continuous panning without any blind areas, supports
255addresses and 220 programmable presets and offers multiple cruising, auto-scan, and
pattern tour tracks. All settings are stored in non-volatile memory. The ST-PTZ530-36 is an
all weather camera with integrated heater and blower.
SPECIFICATIONS&
1. Image Sensor
¼” EX-View HAD CCD
2. Resolution
530TVL
3. Picture Elements
NTSC: 768x494
4. Lens
3.4mm ~ 122.4mm, F1.6-F4.5
5. Illumination
0.01 Lux IR On
6. Zoom
432X, 36X Optical, 12X Digital
7. Sync system
internal/External (V-Lock)
8. S/N Ratio
50dB
9. White Balance
ATW / Indoor / Outdoor / Manual / AWB / One Push WB
10. Gain
Auto / Manual
11. Video Output
1Vp-p Composite Video, 75Ω
12. Communications
RS485
13. Protocol
PELCO-P, PELCO-D
14. No. of Programmable Presets
220
15. Focus
Auto / Manual
16. Iris
Auto / Manual
17. No. of Cruising Tracks
8
18. No. of Auto Scan Tracks
8
19. No. of Privacy Zones
8
20. No. of Pattern Tours
4
21. Continuous Pan
360°
22. Manual Speed
0.01°~ 120°/s
23. Max. Cruising Speed
120°/s
24. No. of Addresses
255
25. Operating Temperature
-13°F ~ 122°F (IR Off), -13°F ~ 86°F (IR On)
26. Operating Relative Humidity
<95%
27. Power
110 ~ 220VAC @0.5A

v1.0 12/15/11
4
INSTALLATION&AND&OPERATION&
CAUTION: To reduce the risk of electrical shock do not remove the cover or back of
this unit. No user serviceable parts are inside.
CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than
specified power source.
1. UNPACKING&and&HANDLING&
Each unit is shipped assembled and factory tested.
Ensure that all accessories are removed from the container before discarding packing
material
2. MECHANICAL&INSPECTION&
Inspect the front and rear of the equipment for shipping damage. Make sure the
equipment is clean, and no connectors are broken, damaged, or loose. If equipment
appears to be damaged or defective please contact your distributor or Securitytronix at
1-610-429-1511 for assistance.
3. SPECIAL&ATTENTION&
a. The installer must comply with electrical safety standards. There must be
sufficient space between the camera’s power supply and video line and any high
voltage equipment and/or cables.
b. To help ensure the camera’s life and proper operation do not point the camera
towards the sun or strong light.
c. Do not install the camera in an environment where the temperature is above 122°
F.
d. Do not install the camera near a magnetic field or a high-power motor.
e. Do not mount the camera near a radiator or heater.
f. The installation site and material must fully support the weight of the product.
g. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove
wipe gently with a mild detergent. Never use strong or abrasive detergents.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions.
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electrical shock.

v1.0 12/15/11
5
h. This camera uses AC power of 100 ~ 240 volts at 0.5A. Using a DC or other
incorrect power supply or source will damage the camera.
i. Only qualified installers are allowed to install, test and disassemble the camera.
j. The camera is a low voltage product. If installed outdoors proper safety and
lightning grounding are required in addition to surge protection.
k. Before installing be sure the grounding, wiring, input power, voltage, DIP
switches, communication protocol and baud rate are correctly set prior to
powering up and using.
4. CAMERA&SETUP&
It is advisable to configure the camera’s settings prior to physically installing the unit.
To set the camera’s address and protocol remove the “settings cover” on the side of the
camera. This will expose two sets of 8-bit DIP switches,one each to set the camera’s
protocol and address.
Protocol Set Up
The camera supports PELCO-P and PELCO-D protocols and three baud rates: 9600,
4800 and 2400bps. Using SW2 and the table below:
DIP Switches 1, 2 and 3 set the protocol (“1” means “ON”, “0” means “OFF”)
DIP Switches 4 and 5 set the baud rate (“1” means “ON”, “0” means “OFF”)

v1.0 12/15/11
6
Protocol
Switch 1
Switch 2
Switch 3
PELCO-D
0
1
0
PELCO-P
1
0
0
Reserved
…
…
…
Baud Rate
Switch 4
Switch 5
9600
0
0
4800
1
0
2400
0
1
Reserved
1
1
Camera Address Set Up
SW1 uses all of the 8-bit switches to set up to 255 camera addresses. The 1st bit is the
lowest and the 8th bit is the highest.
See Appendix A for SW1 DIP Switch configurations for PELCO-P and PELCO-D
protocols. Note the DIP Switch settings are slightly different for each protocol.
&
5. PHYSICAL&INSTALLATION&
Unscrew the power box from the mounting bracket. Then thread the cables across the
bracket and connect to the circuit board in the power box.

v1.0 12/15/11
7
Install the camera dome to the bracket
using the four hexagon screws. It is
advisable to apply a waterproof sealant to
the joint gap where the camera dome joins
the bracket.
Attach the mounting template to the location where
the camera is to be mounted. Drill holes according to
the template and install the mounting bolts.
Install the entire unit (camera body,
bracket and power box) to the mounting
bolts and tighten.

v1.0 12/15/11
8
Remove two screws from the power box
and open it.
Thread the power cable through the
waterproof head on the left and the RS485
and video cable through the waterproof
head on the right.
Connect the cables to the circuit board
and double check to ensure each cable is
connected to its proper location. Damage
may occur if cables are improperly
connected.
After all cables are connected, tighten the
two heads. It is advisable to apply
waterproof sealant to the heads.
Close the power box and tighten the bracket to the
box. Double check all bolts and screws are tight. It
is advisable to apply waterproof sealant to all joint
gaps.
After the camera is physically mounted and
installed:
Connect the camera to the monitor with a 75Ωcoaxial video cable.
Connect power supply’s AC plug to a suitable AC power outlet.
Make an RS485 connection between the camera and the PTZ controller. Ensure
the connections at the PTZ controller and camera have the same polarities.

v1.0 12/15/11
9
6. FUNCTIONS&and&OPERATION&
From the PTZ controller calling preset position 95 will display the camera’s On Screen
Display (OSD) menu. The camera’s OSD Menu Tree is below.
!
! ! ! !
!
!! ! ! !
!!!!!

v1.0 12/15/11
10
System Information
A = Camera Dome ID E = TV System (NTSC or PAL)
B = Camera Dome Address F = Camera’s Internal Temperature
C = Baud Rate G = Version
D = Protocol
Display
Call preset 95 to enter the OSD Menu and move the PTZ controller’s joystick to select
DISPLAY and press IRIS OPEN to enter submenu DISPLAY.
A = DOME. Press IRIS OPEN to set the Dome Setting with the ON/OFF option.
B = PRESET. Press IRIS OPEN to set the Preset Setting with ON / OFF / 2SEC / 5SEC /
10SEC option
C = MOTION. Press IRIS OPEN to set the Auto Setting with ON / OFF/ 2SEC / 5SEC /
10SEC option.
D = ZONES. Press IRIS OPEN to set the Zones Settings with ON / OFF / 2SEC / 5SEC /
10SEC option.
E = DATE/TIME. Press IRIS OPEN to set the Date/Time Settings and move the joystick
to select ON / OFF / 2SEC / 5SEC / 10SEC option.
A
B
C
D
E
F
G
A
B
C
D
E
F
G

v1.0 12/15/11
11
F = PAN/TILT. Press IRIS OPEN to set the Pan/Tilt Settings and move the joystick to
select ON / OFF / 2 SEC / 5SEC / 10 SC option.
G = DISPLAY POSITION. This submenu allows the user to set where information is
displayed on the monitor. Move the cursor to Display Position and press IRIS OPEN to
enter the submenu.
A = DATE/TIME. Press IRIS OPEN to set the Date/Time Setting and move
the joystick to move the Date/Time to the desired position. Press IRIS OPEN
to confirm.
B = DOME TITLE. Press IRIS OPEN to set the Dome Setting and move the
joystick to move the Dome to the desired position. Press IRIS OPEN to
confirm.
C = ZONES. Press IRIS OPEN to set the Zones Setting and move the
joystick to move the Zone to the desired position. Press IRIS OPEN to
confirm.
D = MOTION. Press IRIS OPEN to set the Auto Setting and move the joystick
to move the Auto to the desired position. Press IRIS OPEN to confirm.
E = PAN/TILT. Press IRIS OPEN to set the Pan/Tilt Setting and move the
joystick to move the Pan/Tilt to the desired position. Press IRIS OPEN to
confirm.
A
B
C
D
E

v1.0 12/15/11
12
Dome Settings
Call preset position 95 to display the OSD Menu and move the PTZ controller’s joystick
to the DOME submenu. Press IRIS OPEN to enter the DOME submenu.
A = IR LED SETTINGS. Move the cursor to IR LED and press the IRIS OPEN to access
the IR LED submenu.
!!!!!! !
A1 = CONTROL MODE. Move the cursor to CONTROL MODE and press IRIS
OPEN to select the IR light control type. Move the joystick to set the IR light control
type as “External Auto / Internal Auto / Timing / On / Off ”.
External Auto –Turning on or off the IR LED will depend on the light sensor.
When the light sensor detects the environmental light level is lower than the
IR LEDs’ threshold the IR LEDs will turn on and the camera will switch from
color to black and white. When the environmental light level is higher than the
IR LEDs’ threshold the IR LEDs will turn off and the camera switches from
black and white to color.
Internal Auto –Activation of the LEDs are determined by the light level
reaching the CCD, not the external light sensor.
TIMING –The IR LEDs will turn on or off according to the time set by user.
ON –The IR LEDs are always on.
A
B
C
D
E
F
G
H
A1
B1
C1
D1
E1
F1
G1
H1
I1

v1.0 12/15/11
13
OFF –The IR LEDs are always off.
NOTE: The camera’s D/N AUTO is valid unless the camera is set to “Internal
Synchronization Auto”
B1 = THRESHOLD. Move the cursor to THRESHOLD and press IRIS OPEN to
select the desired value. The user can adjust the environmental light threshold value
to suit specific locations. For External Synchronization Auto the default value is
1~2Lux. The threshold value can be set from 1 to 10 with 1 being weak or dim light
and 10 being strong or bright light.
C1 = SENSITIVTY SETUP. When the IR LEDs are on the environmental light
threshold needed to turn off the IR LEDs has a delay. 1 represents high sensitivity
and the delay range is narrow allowing the IR LEDs to turn on and off frequently in
certain light conditions. 10 represents low sensitivity and the delay range is wide
thereby causing the IR LEDs to turn on and off less frequently. The default value is 5.
D1 = START TIME. Press IRIS OPEN to enter the START TIME submenu and move
the joystick left or right to select the desired time value to be changed, then move the
joystick up or down to change the value.
E1 = STOP TIME. Press IRIS OPEN to enter the STOP TIME submenu and move
the joystick left or right to select the desired time value to be changed, then move the
joystick up or down to change the value.
NOTE: It is more effective to set the IR LED start and stop times in the Timing Mode.
F1 = ZOOM MATCH. Press IRIS OPEN to set the ZOOM MATCH. When OPEN is
selected the illumination and power of the IR LEDs are matched with the camera’s
illumination distance. With a different zoom the IR LEDs will automatically adjust its
power. When CLOSE is selected the IR LED illumination level is set manually by the
user. It is recommended that Open Zoom Match be selected.
G1 = LED 1POWER. Light group 1 consists of the perimeter IR LEDs and
illumination for longer distances. Press IRIS OPEN to set the illumination value.
H1 = LED 2 POWER. Light group 2 consists of the center circular IR LEDs and
illumination of medium distances. Press IRIS OPEN to set the illumination value.
I1 = LED 3 POWER. Light group 3 consists of the inner IR LEDs and illumination of
shorter distances. Press IRIS OPEN to set the illumination value.
NOTE: If zoom match is set to off, the manual adjustment of the illumination levels
will be required.
NOTE: If zoom match is set to on, the adjustment illumination levels of the Light
Groups is done automatically.

v1.0 12/15/11
14
B = STANDBY SETTINGS. Move the cursor to STANDBY SETTINGS and press IRIS
OPEN to enter the STANDBY SETTINGS submenu.
A1 = STANDBY TIME. Move the cursor to TIME and press IRIS OPEN to set up the
time. Move the joystick and time can be set to 30sec / 2min / 5min / 10min. Press
IRIS OPEN to confirm.
B1 = STANDBY ACTION. Move the cursor to MOTION and press IRIS OPEN to set
up the motion. Move the joystick and motion can be set to preset 1 /scan 1 /cruising
tour 1 / pattern tour 1 / no control. Press IRIS OPEN to confirm.
C = PRIVACY MASK. Move the cursor to PRIVACY MASK and press IRIS OPEN to
enter the PRIVACY MASK SETTINGS submenu.
A1 = PRIVACY MASK. Move the cursor to MASK NO. and press IRIS OPEN to set
up. Move the joystick to select any one of eight privacy masks.
B1 = ENABLE. Move the cursor to ENABLE and press IRIS OPEN to enable the
privacy mask. Move the joystick to select the mask’s state: On / Off.
C1 = SETUP.Move the cursor to SET and press IRIS OPEN to set up the privacy
mask’s position. Press IRIS OPEN to confirm. Then move the cursor to the privacy
A1
B1
A1
B1
C1
D1

v1.0 12/15/11
15
mask, press IRIS OPEN to enter the privacy size setting and move the joystick to
adjust the size of the privacy area. Press IRIS OPEN to confirm.
D1 = DELETE. Move the cursor to DELETE and press IRIS OPEN to delete the
selected privacy mask.
D = CLOCK. Move the cursor to CLOCK and press IRIS OPEN to enter the CLOCK
submenu.
A1 = DATE SETTING. Move the cursor to DATE and press IRIS OPEN to set up the
date. Shift the joystick right or left to the desired setting position, then move the
joystick up or down to adjust the date. Press IRIS OPEN to confirm.
B1 = TIME SETTING. Move the cursor to TIME and press IRIS OPEN to set up the
time. Shif the joystick right or left to the desired setting position, then move the
joystick up or down to adjust the time. Press IRIS OPEN to confirm.
E = MANUAL LIMIT. Move the cursor to MANUAL LIMIT and press IRIS OPEN to enter
the MANUAL LIMIT submenu.
A1
B1
A1
B1
C1

v1.0 12/15/11
16
A1 = SETUP LEFT LIMIT. Move the cursor to LEFT LIMIT and press IRIS OPEN to
set up.
B1 = SETUP RIGHT LIMIT. Move the cursor to RIGHT LIMIT and press IRIS OPEN
to set up.
C1 = MANUAL CONTROL. Move the cursor to MANUAL LIMIT and press IRIS
OPEN to set up. Move the joystick to select On / Off.
F = PASSWORD SETTINGS. Move the cursor to PASSWORD and press IRIS OPEN to
enter the PASSWORD SETTINGS submenu.
A1 = MODIFY PASSWORD. Move the cursor to EDIT PASSWORD and press IRIS
OPEN to enter the password modification mode. Input the old password first. Input
the new password. Press IRIS OPEN to confirm. The default password is “111111”.
B1 = PASSWORD PROTECTION. Move the cursor to ENABLE and press IRIS
OPEN to enter the password protection mode. Move the joystick up or down to
enable or disable password protection. Press IRIS OPEN to confirm. When password
protection is enabled, enter the password before opening the menu.

v1.0 12/15/11
17
G = DOME TITLE SETUP. Move the cursor to DOME TITLE SETUP and press IRIS
OPEN to enter the DOME TITLE SETUP submenu.
! ! !!!!!!!!!!!! !
! ! !!!!!!!!!!!! !
! ! !!!!!!!!!!!! !

v1.0 12/15/11
18
INPUT METHOD.
Move the cursor to INPUT and press IRIS OPEN to enter the information edit
mode. Move the joystick left and right to move the cursor “←”and press IRIS
OPEN to delete the character and press IRIS CLOSE to exit the edit mode.
Move the cursor to the line below “INPUT”. Press IRIS OPEN to enter the
INPUT METHOD setup. Move the joystick up and down to chose the desired
input method: English Capital / English Lower Case / Chinese / Number /
Special Character.
Move the cursor to one line below “INPUT” and press IRIS OPEN to enter the
character input mode. The selected character twinkles. Move the joystick to
the desired character and press IRIS OPEN to input the desired character
next to “←”in the input information block.

v1.0 12/15/11
19
H = OTHER OPTIONS. Move the cursor to OTHER OPTIONS and press IRIS OPEN to
enter the OTHER OPTIONS submenu.
A1 = TEMPERATURE CONTROL MODE. Move the cursor to the TEMPERATURE
MODE and press IRIS OPEN to enter the set up. Use the joystick to select “Cool /
Auto / Heat / Off” option and press IRIS OPEN to confirm the selection.
NOTE: With the IR LEDs on the fans will be set as “always on”.
B1 = PRESET FREEZE. In calling the preset setup menu, move the cursor to
PRESET FREEZE and press IRIS OPEN to enter set up. Move the joystick to select
“On / Off’ and press IRIS OPEN to confirm.
C1 = AUTO FLIP. When the camera dome rotates 90°in the vertical direction and
the user wants to continue the vertical rotation the dome will automatically rotate by
180°in 2 seconds. Press IRIS OPEN to turn this function On or Off.
D1 = AUTO STOP TIME. Auto pause time refers to the period of time when the
dome does not receive any input, and after that the camera will automatically pause.
Options are 15, 30 and 60 seconds.
E1 = MENU OFF TIME. The menu will automatically shut off after a period of
inactivity. Move the cursor to MENU OFF TIME and press IRIS OPEN to set up.
Move the joystick up or down to select the “1 mins / 2 mins/ 5 mins / 10 mins” option.
F1 = NORTH SET. Move the cursor to NORTH SET and press IRIS OPEN to enter
the set up mode. When “Press IRIS OPEN to Confirm” is displayed the user can
move the dome to a horizontal zero position (North). Press IRIS OPEN to set this
position as the zero position.
A1
B1
C1
D1
E1

v1.0 12/15/11
20
Camera Setup
From the Main Menu move the cursor to CAMERA SETUP and press IRIS OPEN to enter
the CAMERA SETUP submenu.
A = AUTO FOCUS. Move the cursor to AUTO FOCUS and press IRIS OPEN to enter
the AUTO FOCUS setup menu. Move the joystick up or down to select the focus mode.
B = DIGITAL ZOOM. Move the cursor to DIGITAL ZOOM and press IRIS OPEN to enter
the DIGITAL ZOOM setup menu. Move the joystick up or down to switch the digital zoom
On or Off.
C = BACKLIGHT COMPENSATION. Move the cursor to BACKLIGHT and press IRIS
OPEN to enter the BACKLIGHT setup menu. If the picture illumination is low use the
joystick to switch the backlight compensation on to increase the illumination.
D = PICTURE FREEZE. Move the cursor to FREEZE and press IRIS OPEN to enter the
PICTURE FREEZE setup menu. Move the joystick up or down to turn On or Off this
function.
E = VERTICAL REVERSE.Move the cursor to VERTICAL REVERSE and press IRIS
OPEN to enter the VERTICAL REVERSE MENU. Move the joystick up or down to flip the
image vertically.
F = ZOOM SPEED. Move the cursor to ZOOM SPEED and press IRIS OPEN to enter
the ZOOM SPEED setup menu. Move the joystick to the select the camera’s zoom
speed option: “ Low Speed, Moderate Speed, High Speed”.
G = DAY/NIGHT.This feature defaults to AUTO, and cannot be adjusted.
H = ADVANCED OPTION. Move the cursor to ADVANCED OPTION and press IRIS
OPEN to enter the ADVANCED OPTION submenu.
A
B
C
D
E
F
G
H