Interlogix UltraView UVD-6130VE-2 Series User manual

UltraView UVD-6130VE-2
WDR Dome Camera User
Manual
P/N 1072549A • REV 1.0 • ISS 18JUN12

Copyright
©
2012 UTC Fire & Security. All rights reserved.
Trademarks and
patents
The
TruVision and Interlogix names and logo are trademarks of
UTC
Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
UTC Fire & Security Americas
Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance
Class A:
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated i
n a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
ACMA compliance
Notice!
This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
European Union
directives
12004/108/EC (EMC directive):
Hereby, UTC Fire & Security
declares that this device is in compliance or with the essential
requirements and ot
her relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upo
n the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information
, see www.utcfireandsecurity.com or
www.utcfssecurityproducts.eu
.

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 1
Content
Product overview 2
Package Contents 2
Features 2
User guidelines 3
Product description 3
OSD control pad 3
Installation 5
Mount the camera 5
Connect the cables 5
Adjust the lens 5
Adjust the focus and zoom 6
Programming 7
Access the Setup menu 7
Select the lens type 8
Set shutter/AGC 8
Adjust the picture characteristics 10
Set white balance 10
Set WDR 11
Set image noise reduction 12
Set HLC and BLC 12
Set Day/Night mode 13
Set E-zoom 14
Set DIS 14
Set the privacy mask area 14
Set motion detection 15
Display the synchronization mode 15
Set the camera ID 16
Select the language 16
Reset camera settings 16
Save all changes 16
Specifications 17
Dimensions 17
Menu Map 18

2 UltraView UVD-6130VE-2 WDR Dome Camera User Manual
Product overview
The UVD-6130VE-2 WDR camera uses a digital signal processor (DSP) to
process video signals. The camera includes a microcontroller to provide high-
quality images with high-color reproduction and sharp pictures.
Package Contents
The package contains the following:
• Dome camera
• Monitor output cable
• Mounting screws, wall anchors, and hex wrench
• Power terminal
• Ceiling drilling holes template
• Quick start guide
Note: Use the video output BNC and power jack for normal system operation.
Use the monitor output cable for installation and maintenance.
Features
The camera includes the following features:
• Super HAD II (hole accumulated diode) technology with 480,000 pixels NTSC
(570,000 PAL)
• Use of LSI (large scale integration) digital processors to produce 650 lines of
horizontal resolution
• Smart digital control automatic BLC (backlight compensation)
• WDR (wide dynamic range)
• Advanced auto exposure system for both fixed iris and auto iris lenses to
optimize the amount of light
• Internal synchronization
• Eight privacy mask areas to protect privacy concerns
• Advanced OSD (onscreen display) control
• Signal-to-noise ratio better than 52 dB
• Long life and high reliability
• Isolated switching power 12 VDC and 24 VAC

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 3
User guidelines
• Program the camera settings as much as possible before mounting the
camera. Take appropriate safety precautions while completing programming
after installation.
• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the
camera.
• Do not use the camera over the temperature range specifications: -10°C to
+50°C (14°F to 122°F)
• If the light source where the camera is installed experiences rapid, wide-
variations in lighting, the camera may not operate as intended.
WARNING: To reduce the risk of fire or electronic shock, do not expose the
camera to rain or moisture and do not remove the cover or back.
Product description
Figure 1:: Camera description
Camera body
OSD control
pad
System heater
Power jack
Monitor output cable:
1. Monitor output BNC; 2.
Monitor output RCA
Video monitor output Video output BNC
OSD control pad
The onscreen display (OSD) control pad (Figure 3) is a five-direction pad that
provides the ability to manually control the camera functions. Table 1 below lists
the OSD control pad functions and describes their use.

4 UltraView UVD-6130VE-2 WDR Dome Camera User Manual
Figure 2: OSD control pad
OSD control pad
Table 1: OSD control pad functions
Pad directions Description
Up Moves the cursor upward to select an item.
Left Moves the cursor left to select or adjust the options of the selected
item.
Right Moves the cursor to the right to select or adjust the options of the
selected item.
Down Moves the cursor downward to select an item.
Enter
Press the center of the control pad to display the Setup menu. If the
selected item has its own menu, press the control pad to enter a
submenu. Press the control pad for 2 seconds to save all settings
and exit the Setup menu.

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 5
Installation
Please check the package contents and make sure that the device in the
package is in good condition and all the assembly parts are included.
To install the camera you will need to prepare the mounting surface, mount the
camera, make cable connections, adjust the lens and then secure the dome
cover securely.
Note: Before installing, please ensure that the mounting surface is strong enough
to withstand three times the weight of the camera. If the mounting surface is not
strong enough, the camera may fall and cause serious damage.
Mount the camera
Use the ceiling drilling holes template and mark the holes on the ceiling with a
pen. Attach the plate with fasteners to the ceiling and then attach the camera
body to the plate.
To mount the camera, attach the camera to the mounting surface using the
appropriate fasteners.
Connect the cables
To connect the cables:
1. Connect a coaxial cable from the camera’s BNC connector to a CCTV
monitor or video recording device.
2. Connect the 12 VDC or 24 VAC power supply to the power jack of the
camera.
Caution: Check for polarity when using a 12 VDC power supply.
Adjust the lens
The camera is mounted on a pan-tilt-twist (3-axis grimbal) rotating platform so
that it is easy to adjust the camera orientation. See Figure 3 on page 6.

6 UltraView UVD-6130VE-2 WDR Dome Camera User Manual
Figure 3: Camera adjustment
Platform horizontal adjustment (0 to 180°)
Platform vertical adjustment (0 to 90°)
Rotor horizontal adjustment (0 to 350°)
To adjust the lens:
See Figure 3 above.
1. To adjust the horizontal angle of the platform up to 180 degrees, turn the
platform.
2. To adjust the horizontal angle of the rotor up to 350 degrees, turn the rotor on
the platform.
3. To adjust the vertical angle of the platform up to 90 degrees, turn the
platform.
Adjust the focus and zoom
Figure 4: Zoom and focus adjustment
Zoom ring thumbscrew
Focus ring thumbscrew
To adjust the camera zoom and focus:
1. Loosen the zoom ring thumbscrew and turn the zoom ring to set the desired
zoom. Tighten the thumbscrew.
2. Loosen the focus ring thumbscrew and turn the focus ring to set the desired
focus. Tighten the thumbscrew.

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 7
Programming
Once the camera hardware has been installed, the camera can then be
configured.
Access the Setup menu
The Setup menu provides access to the camera configuration options. The on-
screen display (OSD) is only available in English.
Program the camera by attaching a standard video monitor to the system.
Figure 5: The Setup menu screens
Table 2: Setup menu description
Menu item Description
Lens Defines the camera ID, mirror, and digital noise reduction (DNR) set up.
Shutter/AGC Defines the method of iris control.
Pict Adjust Defines the image quality functions.
White Bal Defines the white balance (WB) set up.
WDR Defines the wide dynamic range (WDR) set up.
NR Defines the digital noise reduction level.
BLC/HLC Defines the highlight compensation (HLC) and backlight compensation
(BLC) set up.
Day/Night Defines the day/night (D/N) set up.
EZoom Enables/disables digital zoom.
DIS Enables/disables the digital image stabilizer.
Privacy Defines privacy mask set up.
Motion Det Defines the motion detection set up.
Sync Displays the current synchronization mode.
Camera ID Defines the camera ID displayed on-screen.
Language Defines the language of the OSD.
Camera Reset Resets the camera to factory default settings.
Save All Saves changes made.
Exit Exits the menu and returns to live mode.

8 UltraView UVD-6130VE-2 WDR Dome Camera User Manual
To access the Setup menu:
1. Press the OSD control pad (Enter) to access the Setup menu and its
submenus.
2. Push the pad up, down, left and right to move between menu options.
3. Press the OSD control pad to select an option.
4. When in a sub menu, select Return to return to the previous menu.
5. To save configuration changes, move the cursor to Save All at the bottom of
the screen and press Enter
6. To exit a menu and return to live mode, move the cursor to Exit at the bottom
of the screen and press Enter.
Select the lens type
In the Setup menu, go to Lens and select the type of lens used with the camera,
Auto or Manual. Select Manual for a manual lens and adjust the options
manually, or select Auto to set the lens type to autoiris. The Autoiris menu
appears.
Autoiris menu:
Type: Select the drive mode of the lens. Only DC is available.
Mode: Select the iris control mode. Auto (automatically controlled depending on
the light), Open (always open), or Closed (always closed).
Speed: When the mode is set to Auto, select the convergence speed of the iris
between 0 and 255.
Set shutter/AGC
In the Setup menu, go to Shutter/AGC and select the required iris control option:
Manual, Auto or Traffic. Auto is default. The selected menu appears: