Segway PJ22IOT User manual

User Manual
IoT Device
Model: PJ22IOT

1.Introduction
Thank you for purchasing the IoT devices of Segway Inc.!
The IoT device is designed for the shared scooter and it could communicate with the cloud server via cellular
communication.
Our IoT device is highlighted with the following features. First of all, you could fully control the scooter, such as
lock/unlock, power on /off, turn on/off the throttle, and switch between different riding modes, etc. Secondly, it could help
monitor the state of the scooter through its communications with the server, such as sending alarms, firmware version
information, battery temperatures, etc. In addition to that, it also has the auxiliary features like prompt voice and it has
the superior waterproof design.
This user manual provides an overview of the basic functions of the IoT device. Please read it carefully to ensure your safe
and proper usage of the IoT device.
The pictures showed in this user manual are for reference only. For the exact information of the IoT device, please subject
to the packed goods. The accessories in the package may be different according to different models of scooters which will
be connected to the IoT device, please subject to the shipped goods.
If other details required, please contact our technical staff.
Email: [e-mail]
Service time: Monday to Saturday, 9:00-18:00(GMT+8).
The Copyright belongs to Segway Inc. Without any written permission, any company or individual should not abstract it
in any way.
This user manual is for reference only, it does not constitute any commitment to product. Please prevail in kind.

2.Basic Parameters
Item
Specification
Cloud Communications
Connected to the server through TCP socket
Bands of Northern America Version(US, Canada)
FDD
-LTE B2/B4/B12
UMTS/HSPA+ B2/B5
Bands of EMEA Version
(EMEA/Korea/Thailand)
FDD
-LTE B1/B3/B5/B7/B8/B20
TDD
-LTE B38/B40/B41
UMTS/HSPA+ B1/B5/B8
GSM/GPRS/EDGE 900MHz/1800MHz
Bands of Australia Version
(Australia/New Zealand/South America/Taiwan)
FDD
-LTE B1/B2/B3/B4/B5/B7/B8/B28
TDD
-LTE B40
UMTS/HSPA+ B1/B2/B5/B8
GSM/GPRS/EDGE 850MHz/900MHz/1800MHz/1900MHz
Bands of Japan(Japan)
FDD
-LTE B1/B3/B8/B18/B19/B26
Connectivity/BLE
BLE4.0 (2402
-2480MHz) (Auxiliary unlocking)
GNSS
GPS+GLONASS/GPS+BDS
Antenna Efficiency
Celluar>40%; GPS>70%
Unlocking Time
1
-3s
Geolocation Precision
≦
15m (open ground, sunny unobstructed)
Geolocation Time
Hard/Cold Boot <35s; Soft/Warm Boot<1s (open field)
Max. RF Power transmitted:
(Declaration for EU Compliance)
Bluetooth:
-5.89 dBm
GSM:
33.0 dBm; DCS: 30 dBm
UMTS:
Band I: 22.60 dBm, Band VIII: 23.44 dBm
LTE: Band 1: 22.85
dBm, Band 3: 22.99 dBm, Band 7: 23.75 dBm
Band 8: 24.12 dBm, Band 20: 23.89 dBm, Band 38: 24.02 dBm, Band 40: 23.38 dBm

2.Basic Parameters
Item
Specification
Voice Prompts
Factory Defaults; Volume:70
-90dB
Motion Detection
Triaxial Accelerometer
Operating Temperature
-
20℃ ~ 60℃
Storage Temperature
-
40℃ ~ 70℃
Operating Humidity
93%RH
IP Rating
IPX7
Unlocked state current
<40mA (36VDC average current)
Lock state (standby) current
<5mA (36VDC average current)
Battery&Communication Interfaces
5pin:36V,GND,TX (TTL),RX (TTL), Power_control_wire
Battery Supply Voltage
36VDC
Built
-in Lithium Battery
3.7V/1000mAH
（adaptation）
Backup Battery Life
>2h
Dimensions
170 X 80 X 56mm
Housing Material
PC+10%GF
Certifications
FCC/CE/*other customized certifications for different demands

3.Main Features
Main Features(Firmware Version: SD1.0.5) *This will be continuously updated
Lock&unlock
, power on/off through both 4G and BLE4.0.
Two modes to locate: Single/Continuous
Adjustable sensitivity of accelerometer
User
-defined communication interval between server and IoT
Headlight switch: manual or programmable
Enable/Disable Riding Modes Switch
Riding modes switch:manually or programmable
Enable/Disable Throttle, Cruise control
, Front&rear lights flash
Searching scooter module
User
-defined Max. Speed of different Riding Modes
Read and report scooter information remotely (speed, estimated battery life, Riding Modes. distance travelled and estimated r
ema
ining mileage, temperatures
of scooter motor and mainboard, etc.)
Monitor charging state
Play voice prompts
IoT device dismantled alarm
Low batter alarm
Illegal scooter movements or shaking alarm
Scooter fallen down alert (report to server, no alarm)
Scooter fault alert
Remote firmware upgrades of scooters and IoT devices

4.Diagram
b
c
d
e
a. IoT Device*1
b. Rubber Stopper *4
c. Fixer (U-shaped holder and board part)*1
d. Screw (M5*12)*4
e. Screw (M4*12)*4

5.Main Body Diagram
Speaker
Serial
Number
Label
Rubber
Stopper
IMEI Code
Label
5 Pin Cable
Product Label
Certification
Label

6. Assembling
a. The stem: Remove the four anti-theft screws fixed to dismantle the stem.

6. Assembling
b. The U-shaped holder: Put it on the stem and move it to the position as shown in the picture. Then reassemble
the stem.

6. Assembling
c.The board part: First, pull the 5 pin cable of the scooter through the hole on board part. Second, after locating
the board part according to the 2 screws on the stem, mount the 4 screws (M5*12) to attach the board part to
the U-shaped holder.

6. Assembling
d. The IoT device: First, connect the 5 pin cable of the scooter with that of the IoT device.
Second, mount the 4 screws(M4*12) to attach the IoT device to the board part. Third, mount
the 4 rubber stoppers to the holes on the IoT device.

7.Notes
1. Do not use the IoT device beyond the operating temperature range: -20℃ ~ 60℃.
2. Do not dismantle the IoT device to change SIM card inside because this will weaken its waterproof
performance.
3. Keep the IMEI code label and Serial Number code label adhered on the IoT device intact.
4. Fixer may vary depending on the model of the scooter.
5. Environment surroundings, terrain and other factors may affect the signal quality of GPS and cellular
communication.
6. The IoT device is a highly customized product. SIM cards will be installed into the IoT device in advance and t
he IP address of the server to which the IoT device will be connected will be written to the firmware. Please con
firm this customization info with the manufacturer before your purchase.

8. Regulatory Info
FCC Regulatory Compliance
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

8. Regulatory Info
Supplier's Declaration of Conformity
47 CFR §2.1077 Compliance Information
Unique Identifier:
Trade Name: Segway
Model No.: PJ22IOT
Responsible Party –U.S. Contact Information
Segway Inc.
14 Technology Drive, Bedford, NH 03110
Phone: [phone]
Fax: [phone]
www.segway.com
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

8. Regulatory Info
ISED Regulatory Compliance
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.

8. Regulatory Info
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with minimum distance 20cm between the
radiator and your body.
CAN ICES-3 (B)/NMB-3(B)
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un
environnement non contrôlé. Cet émetteur ne doit pas être situéou fonctionner conjointement avec une autre
antenne ou un autre émetteur. Cet équipement doit être installéet utiliséavec une distance minimale de 20
cm entre le radiateur et votre corps.

Segway Inc.
14 Technology Drive, Bedford, NH 03110
Phone: [phone]
Fax: [phone]
www.segway.com
Hereby, Ninebot (Changzhou) Tech Co., Ltd declares that the
radio equipment type PJ22IOT is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address:
https://www.segwaydiscovery.com/downloads/User_Manual_of
_IoT_device_PJ22IoT.pdf