SEI Chelmsford HE4011R0TX User manual

HE4011R0TX
“Chelmsford”Entry Mirror
Assembly Instructions
For assistance with assembly,
contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
PO#12639

HE4011R0TX
“Chelmsford”Entry Mirror
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
padded surface like carpet or blanket. Check that you have all parts indicated. Call customer service if
hardware is missing. Before beginning assembly, carefully study the diagrams below and sort your
hardware according to the pictures. Using the incorrect hardware will cause damage.
A
Top Panel
B
Left Side Panel
C
Right Side Panel
D
Back Panel
E
Bottom Stretcher
F
Shelf
G
Hanger
H
Bolts
∮
5/32”x 25
I
Wrench
J
Cam Bolt
∮
1/4”x1-1/2”
K
Cam Lock
∮
5/8”x1/2”
L
Cam-Tool
M
Screws
N
Plastic Anchor
O
Cotton Mat
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
Call customer service at 1-800-633-5096
for assistance, questions, or parts.
Assembly Tool Required
No.2 Phillips Screw Driver
Quantity
Of 1 Quantity Of 1 Quantity
Of 1
Quantity
Of 1 Quantity Of 1 Quantity Of 1
Quantity
Of 4
Quantity
Of 6
Quantity
Of 1
Quantity
Of 2 Quantity
Of 2
Quantity
Of 17
Quantity
Of 17
Quantity
Of 1
Quantity
Of 4

HE4011R0TX
“Chelmsford”Entry Mirror
Assembly Instruction
Figure 1
NOTE: Make sure the mounting
holes on the back of Back Panel
(D)
are on the top part of the panel.
Step 1:
Rotate 3 Cam-Bolts (J) into
corresponding holes in Cross-Panel (F).
Step 2:
Insert Cam-Bolts (J) into holes in panels
(D) and (E) and secure using
Cam-Locks (K).
Figure 2
Step 3:
Rotate 10 Cam-Bolts (J) into holes in
Side Panels (B) and (C).
Step 4:
Insert Cam-Bolts (J) into holes in panels
(D), (E), (F) and secure using
Cam-Locks (K).

Figure 3
Step 5:
Rotate 4 Cam-Bolts (J) into holes in Top
Panel (A).
Step 6:
Insert Cam-Bolts (J) into holes in panels
(B), (C), (D) and secure using
Cam-Locks (K).
Step 7:
Attach the 4 wooden pegs (G) to rear
panel (E) using 4 screws (H) which are
inserted through the back of panel (E).
Tighten using Allen Wrench (I).
Figure
Step 8:
Cover Cam-Locks (K) with Cotton Mats
(O) provided.

Figure 5
Step 9:
Locate the wall mirror on a solid wall
and at a comfortable height off the floor,
normally eye level.
Measure the wall and mark the wall
mirror width and height. See Figure 5.
Please mount at least one screw directly
into a wall stud. Wall anchor is not
needed when mounting the screw
directly into a wall stud.
Figure 6
Step 10:
Measure the wall and mark the location
of the center of each of the two screw
mounting holes, see Figure 6.
Using the level, make sure that the two
marks are level to the wall.
Using the power drill and 3/16”drill bit,
drill two 3/16”holes through the
wall board at the mounting hole marks.

Figure 7
Figure 8
NOTE: Make sure not to drill into
electrical wiring or plumbing pipes.
Step 11:
Insert one of the plastic anchors into one
of the two 3/16”holes, see Figure 7.
Make sure that the wall anchor is flush
with the wall.
NOTE: It may be necessary to use a
small hammer to gently tap the anchor
into place.
Step 12: Using the Phillips head
screwdriver install one screw into each
of the anchors, see Figure 7.
Turn the screw in until there is a gap of
1/4”between the head of screw and the
wall surface.
Step 13:
Install the wall mirror (1, Figure
8) onto the two mounting screws using
the mounting holes (2, Figure 8). The
proper and secure mounting of the wall
mirror is when the top edge of each of
the mounting holes is resting securely
on the mounting screw (3, Figure 8).
NOTICE
Using the level, check to make sure that
the wall mirror is horizontally level and
vertically plumb (straight up and down).

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at [e-mail]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity
Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019