SEI HZ104800TX User manual

Page | 1
HZ104800TX
Wine/ Bar Cabinet
Assembly Instruction
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
PO# 13412

Page | 2
HZ104800TX
Wine/ Bar Cabinet
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage. Before beginning assembly,
separate each type of screw. Carefully study the screw diagrams below.
You may receive extra hardware with your unit.
A1pc
Left Top Panel
B1pc
Right Top Panel
C1pc
Support Bar
D1pc
Door Panel
E1pc
Back Panel
F1pc
Back Panel
G 1pc
Bottom Shelf
H4pcs
Leg
I1pc
Left Side Panel
J1pc
Right Side Panel
K1pc
Left Front Panel
L1pc
Right Front Panel
M1pc
Left Back Panel
N1pc
Right Back Panel
O2pcs
Upper Side Shelf
P4pcs
Lower Side Shelf
Q1pc
Drawer Front Panel
R1pc
Drawer Back Panel
S1pc
Left Side Panel
T1pc
Right Side Panel
U1pc
Drawer Bottom
V1pc
Drawer Support
W2pcs
Horizontal Panel
X5pcs
Vertical Panel
Y1pc
Shelf
Z4pcs
File Rod
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the finish.
Avoid rubbing or scratching the surface with rough or
abrasive objects.
For replacement parts or questions, please call
Customer Service at 1-800-633-5096.
Assembly Tool Required
Phillips and Flat Head Screwdriver

Page | 3
HZ104800TX
Wine/ Bar Cabinet
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage. Before beginning assembly,
separate each type of screw. Carefully study the screw diagrams below.
You may receive extra hardware with your unit.
1 26pcs
Wood Dowel
( Ø5/16 X 1”)
2 28pcs
Cam Bolt (1-7/16”)
3 28pcs
Cam Lock
4 12pcs
Bolt (Ø1/4 X 2-3/8”)
5 16pcs
Spring Washer
6 16pcs
Flat Washer
7 8pcs
Barrel Nut
8 4pcs
Bolt (Ø1/4 X 1-3/16 ”)
9 8pcs
Screw (1-3/16”)
10 2pcs
Bolt (Ø1/4 X7/8”)
11 2pcs
Knob
12 12pcs
Screw (5/8”)
13
DOOR HINGE (2pcs)
SCREW (1/2”) (12pcs)
14 2pcs
Magnet
15 1pc
Door Hinge (Left)
16 1pc
Door Hinge (Right)
17 1pc
Allen Key
18 1pc
Plastic Anchor
19 1pc
Screw (1-3/16”)
20 1pc
Screw (5/8”)
21 1pc
Anti-Tip Strap
22 2pcs
Flat Washer
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the finish.
Avoid rubbing or scratching the surface with rough or
abrasive objects.
For replacement parts or questions, please call
Customer Service at 1-800-633-5096.
Assembly Tool Required
Phillips and Flat Head Screwdriver

Page | 4
HZ104800TX
Wine/ Bar Cabinet
Assembly Instructions
Step 1:
Insert Wood Dowels (1) and
screw Cam Bolts (2) into Left
Back Panel (M) and Right
Back Panel (N).
Attach Upper Side Shelves
(O) and Lower Side Shelves
(P) with Back Panels (M) & (N)
using Cam Locks (3).
Turn Cam Locks clock-wise to
secure panels (P) & (O).
Step 2:
Screw Cam Bolts (2) to Left &
Right Side Panels (I) & (J).
Attach assembled panels from
Step 1 to Left Side Panel (I)
and Right Side Panel (J) by
inserting attached Cam Bolts
into corresponding holes.
Secure with Cam Locks (3)
and turn clock-wise with a
Phillips screwdriver.
Note: Back Panel (M)
corresponds to Left Side
Panel (I) and Back Panel (N)
corresponds to Right Side
Panel (J).
M
P
3 2 1
P
O
P
P
O
N
I
M
3
3
3
2
2
2
J
N
3
3
3
2
2
2

Page | 5
Step 3:
Insert File Rods (Z) into
corresponding holes.
Attach Left Front Panel (K)
and Right Front Panel (L)
using Wood Dowels (1), Cam
Bolts (2) and Cam Locks (3).
Note: Make sure to attach
the File Rods (Z) onto both
units.
Step 4:
Attach Door Hinges (13) to
Shelf (Y) using supplied
Screws for hinges.
Attach Shelf (Y) to Door Panel
(D) as shown.
K
IJ
L
2
1
3
ZZ
Z
Z

Page | 6
Step 5:
Attach assembled unit from
Step 3 that has Right Side
Panel (I) to assembled unit
from Step 4 using Wood
Dowels (1), Barrel Nuts (7),
Spring Washers (5), Flat
Washers (6) and Bolts (4).
Tighten withAllen Wrench
(17).
Note: Make sure threaded
holes in Barrel Nuts are facing
adjacent holes where Bolts will
come through to meet.
Also note placement of
grooves and make sure to
match as shown.
Step 6:
Attach Magnets (14) to Left
Side Panel (I) and Right Side
Panel (J) using Screws (12).
Y
7
7
1
1
654
17
I
I
14 12
12
J

Page | 7
Step 7:
Attach Support Bar (C) using
Wood Dowel (1), Cam Bolt (2)
and Cam Lock (3).
Slide Back Panel (E) into
grooves of Support Bar (C)
and Shelf (Y).
Step 8:
Attach Right Side Panel (J) to
Shelf (Y) and Support Bar (C)
using Wood Dowels (1), Cam
Bolts (2), Cam Locks (3),
Barrel Nuts (7), Spring
Washers (5), Flat Washers (6)
and Bolts (4).
Tighten Bolts with Allen
Wrench.
312
E
I
C
C
Y
J
7
17
4
5
6
1
321

Page | 8
Step 9:
Attach Bottom Shelf (G) using
Spring Washers (5), Flat
Washers (6), Barrel Nuts (7)
and Bolts (4).
Tighten Bolts with Allen
Wrench.
Step 10:
Attach Legs (H) using Spring
Washers (5), Flat Washers (6)
and Bolts (4).
H
H
HH
17
4
5
6
G
F
4
5
6
7
1

Page | 9
Step 11:
Attach Door Hinges (16) using
Screws (12).
Attach Knob (11) using Bolt
(10).
Step 12:
Insert Wood Dowels (1) into
corresponding holes.
Place Left Top Panel (A) and
Right Top Panel (B) on to top
as shown.
Secure using Spring Washers
(5), Flat Washers (6) and Bolts
(8).
Tighten withAllen Wrench.
AB
1
6
5
8
D
12 12
16
10
11

Page | 10
Step 13:
Assemble Left Side Panel (S)
and Right Side Panel (T) with
Drawer Front Panel (Q) using
Screws (9).
Tighten screws with Phillips
screwdriver.
Step 14:
Slide Drawer Bottom (U).
Attach Drawer Support (V)
with Drawer Front Panel (Q)
and Drawer Back Panel (R)
using Cam Bolt (2) and Cam
Lock (3).
Step 15:
Secure Drawer Side Panels
with Drawer Back Panel (R)
using Screws (9).
Q
T
S
9
9
99
U V 2
3
R