Seima Limni Wall Faced Toilet Suite STO-309 User manual

Large end of pan connector
can be trimmed to suit setout.
Threaded
section can be
trimmed to
required size.
Please note
−Installation shall be in accordance with AS/NZS3500.
−All measurements are in millimetres. Height dimensions
are to base of pan. Make allowance for bedding.
−Bedding: Pan may be bedded with cement base or using
silicone sealant. Fix pan to floor using a sand cement
mixture of 3:1 to a depth of 60mm. Do not use lime or
fast-drying cement.
seima.com.au
−Bracket fixing: The pan should be bedded with silicone
sealant and fixed with the brackets supplied.
−Do NOT use epoxy type adhesives.
−Dimensions are nominal and subject to normal ceramic
manufacturing variations.
−Specifications may vary without notice as part of our
continuous improvement practices.
−Clean with a damp cloth. Do not use abrasive cleaners,
liquids or pastes.
CISTERN PACKAGE CONTENTS
1 x ceramic cistern lid
1 x ceramic cistern base
Cistern is supplied with flush
valve and dual purpose inlet
valve already installed.
PAN PACKAGE CONTENTS
1 x ceramic pan 1 x pan connector
For connecting pan to
floor outlet pipe/S-trap.
1 x threaded section
(with flange plate)
Flange attaches to wall;
threaded section links to
pan connector.
2 x concealed
fixing brackets
Optional — can be
used to connect
pan to floor.
2 x floor bolts
(+ white plugs)
2 x washers
Optional fixing #2 —
used with fixing brackets
to secure pan to floor.
Bolt is inserted through
bracket base hole.
2 x caps (chrome plated)
2 x screws
2 x pan plugs (white)
Optional fixing #2 — used to
secure pan to concealed fixing
bracket. Plastic plug is placed
into hole in side of pan exterior,
screw is rebated into plug
and then screws into a hole
in upright section of bracket.
Chrome cap is used to cover
plastic plug.
IMPORTANT
1 Inspect the components before installation to ensure there are no visible
defects. If a defect is found, do not install the toilet suite and contact the
supplier immediately. Claims for defects will not be accepted after the product
has been installed.
2 This toilet suite is suitable for a variety of set-ups:
Cistern — accommodates either Back Entry Inlet connection or Bottom Entry
Inlet connection (left or right stop valve).
Pan — universal trap — accommodates S-trap installation or P-trap installation
(using appropriate connector; not supplied).
3 The toilet suite must be installed by a licensed plumber. Failure to do so may
void the warranty.
4 Installation must be in accordance with AS/NZS3500.
2 x bolts w seals
For attaching
cistern to pan.
2 x plugs
Plugs can be used to
plug holes in sides of
pan if required.
1 x rubber seal
For sealing outlet at
base of cistern.
1 x flush button
Half flush left, full
flush right. Note: The cistern can
be adapted for bottom
entry plumbing. The
bottom entry inlet
valve shown above is
an optional extra.
OPTIONAL EXTRA
bottom entry
inlet valve
Installation Guide
Limni Wall Faced Toilet Suite
limni-wf-in | v 3.0 | page 1 of 4

1 S-TRAP PROCEDURE — SECURING THE PAN
CONNECTOR IN PLACE
Determine the centre of the pan and mark the centre line on the
floor and wall.
Work out the setout required. The recommended setout is
150mm (setout range is 90-190mm).
You may need to trim the large end of the plastic pan connector
to fit the required setout. To trim, first remove the plastic ring and
rubber seal, then cut pipe to size. Refit rubber seal and plastic
ring securely, ensuring a good fit.
Position the pan connector into the floor outlet pipe (S-trap).
The height measurement from the floor to the centre of the pan
connector is 185mm.
Slot the threaded section (with flange plate) onto the pan
connector, ensuring that the flange plate is touching the wall.
You may need to trim the threaded section so that it fits properly.
Mark and drill the flange plate holes and secure the plate to the
wall with fixing screws. The pan connector is now installed.
2 POSITIONING THE PAN
Use the centre line marked on the wall and floor to position the
pan (see Step 1.1). Push the pan into the installed plastic pan
connector.It is recommended that wedges are used to support
the foot of the pan during positioning.
3 CISTERN — COMES SET UP FOR BACK ENTRY
INLET PLUMBING
Diagram A shows the cistern as supplied, with the inlet valve and
flush valve already installed. The flexible hose is ready for Back
Entry inlet plumbing (see Diagram B).
For Bottom Entry Inlet plumbing, refer to Step 5 and Diagrams C
andD.
Page 2 of 4
bottom entry inlet port
hole for flexible hose
(on both sides of pan)
bracket fixing holes
(both sides of pan)
bottom entry water
control holes
cistern/pan
attachment holes
seat connection holes
cistern outlet pipe hole
All measurements are in millimetres.
Height dimensions are to base of pan.
Make allowance for bedding.
This toilet suite can be set up as either Bottom Entry Inlet or Back Entry
Inlet.
Cistern setup as
supplied. The end of the
flexible hose is loose,
ready to be attached
to the Back Entry inlet
nozzle (see Diagram B).
NOTE: FLEXIBLE HOSE NOT
SUPPLIED.
DIAGRAM A
inlet
valve
cistern
flush valve
plug
(flexible hose not
supplied)
21580
440
180
150 rec 150 setout
recommended
(range 90-180)
BACK ENTRY
INLET OPTION:
½” BSP nipple
approx 22mm
projection from
finished wall
22
690
360
385
85
770
860
360
300
350
220
BACK ENTRY
setout position for
½” BSP nipple
Installation Guide
Limni Wall Faced Toilet Suite

6 SECURING THE PAN ON THE FLOOR
Cement fixing (optional fixing #1)
If using cement bedding, level the pan while the cement
mixture is workable. Fix pan to floor using a sand cement
mixture of 3:1 to a depth of 60mm. Do not use lime or fast-
drying cement.
Important: Allow at least 24 hours for the cement mixture
to set before using the toilet.
Bracket fixing (optional fixing #2)
Bed the pan with acetic cured silicone sealant, ensuring that
the pan is level. Then position the concealed fixing brackets
in line with the bracket fixing holes. Screw the floor bolts
in place through the base of the brackets. Then secure the
pan to the brackets using the plastic pan plugs and rebated
screws. The chrome caps can be used to cover the plugs on
each side of the pan.
Important: Do not over-tighten the bolts or screws as this may
cause the ceramic to crack and break.
7 FIXING THE CISTERN TO THE PAN
(Note: The cistern fixes directly onto the pan and does not
require wall fixing.)
First check the alignment of the cistern and pan attachment
holes — place the cistern onto the pan and ensure that the
holes align. The back of the cistern and pan should line up so
that the assembled toilet suite will align with the wall. Now
remove the cistern.
Place the rubber seal onto the plastic pipe outlet at the base
of the cistern and ensure it is securely attached. Locate the
cistern outlet (with rubber seal) onto the pan, ensuring a
good fit.
If using Bottom Entry inlet plumbing, refer to Step5 and install
the back entry inlet valve.
Now secure the cistern to the pan using the two bolts with
seals in the cistern/pan attachment holes.
Flush the lines and connect the water supply and check the
operation of the cistern.
8 FITTING THE CISTERN LID
Fit the flush button into the cistern lid, with the half flush
on the left and full flush on the right. Ensure that the rubber
feet of the flush button connect and line up correctly with the
flush valve inside the cistern.
Fit the cistern lid and push the buttons to check operation.
9 OPERATION AND MAINTENANCE
Press the left side half flush to save water and the full flush as
required.
Clean the toilet with liquid detergent and a damp cloth.
Do not place water additives inside the cistern as this may
have chemicals that damage the valves and impair the
functionality of the cistern.
Page 3 of 4
4 BACK ENTRY INSTALLATION
Connect the flexible hose to the ½” BSP nipple in the wall outlet. Run
the flexible hose behind the flush valve, ensuring that the hose does not
obstruct the operation of the flush valve.
5 CISTERN SET-UP CAN BE ADAPTED FOR
BOTTOM ENTRY INLET PLUMBING
First remove two items: the back entry inlet valve and the plug in the
base of the cistern. Next, install the bottom entry inlet valve with plug in
the hole in the cistern base.
For Back Entry Inlet,
attach the loose end
of the flexible hose
to the ½” BSP nipple
water inlet in wall.
back entry
inlet
valve
cistern
flush valve
DIAGRAM B
The cistern setup after
the back entry inlet
valve and base plug
have been removed.
DIAGRAM C cistern
flush valve
Next, install the
bottom entry inlet
valve with plug
into the hole in the
cistern base. Place
the conical rubber
seal inside the
cistern. Outside the
cistern thread on
the flat rubber seal,
white plastic disc
and white plastic
wing nut in that
sequence.
DIAGRAM D cistern
flush valve
bottom entry inlet valve
remove
plug
remove
back entry
inlet valve
(flexible hose not
supplied)

Page 4 of 4
Secure the toggle bolts into the seat connection
holes, ensuring that the stainless steel pins line
up with the receptor holes in the seat. Once
correctly placed, ensure that the bolts are
properly tightened.
Slide the stainless steel caps onto the plates with
pins.
To fit the seat, slide it onto the stainless steel pins.
You may need to make adjustments to position
the seat correctly.
To release the seat, put the seat in an upright
position, press the buttons on the seat and lift
upwards.
To fit seat, slide seat down
onto stainless steel pins.
To remove seat, put seat
in upright position, press
the buttons on the seat
and lift upwards.
SEAT PACKAGE CONTENTS AND INSTALLATION
1 x seat and lid
Has receptor holes that slide
onto stainless steel pins.
2 x stainless steel caps
(used to cover stainless steel plate w pin)
2 x stainless steel plates with pin
(seat locates onto stainless steel pins)
2 x toggle bolts
(used for securing stainless steel plate and pin to pan)