SelectBlinds Cordless Cellular Fabric Shade User guide

owner's handbook
Cordless
CellularFabric
Shade

2

Semi
-Cell
Shades
Fabric
Cellular
&
3
Young children can STRANGLE in cord and bead chain loops. They can
also wrap cords around their necks and STRANGLE.
• Always keep cords and bead chains out of children’s reach.
• Move cribs, playpens, and other furniture away from cords and bead
chains. Children can climb furniture to get to cords.
• Do not tie cords together. Make sure cords do not twist together
and create a loop.
WARNING

4

Semi
-Cell
Shades
Fabric
Cellular
&
5
INSTALLATION INSTRUCTIONS
Step 1. Check Package Contents
Missing part? Call 800-933-7115
Mounting hardware kit includes the following:
Part Quantity
a Mounting Brackets 2 (for 18” to 36” wide shades)
3 (for 36” to 48” wide shades)
4 (for 48” to 72” wide shades)
5 (for 72” to 96” wide shades)
b 11 /8” Screws 2 per bracket
c. Hold Down Brackets 2 per shade
d ½” Screws 2 per bracket (for hold downs)
e Handle for Bottom Rail 1 (cordless shades only!)
f Handle for Middle Rail 1 (TDBU cordless shades only!)
[Note: one extra screw of each noted size is included for convenience]
Step 2. Tools Required
Screwdriver, tape measure, pencil, drill, drill bits, step ladder.
Note: use #6 plastic anchors for dry wall or plaster mounting (not included).
Drill Bits: for screws, use a 3/32" drill bit - for wall anchors, use 1/4" drill bit.
Step 3. Bracket Location and Installation
Your shade may be installed either inside the window frame or
outside the window frame.
A mounting bracket should be positioned about 1” to 6” from
each end of the head rail. For wider shades that require 3 or
more brackets, these should be spaced evenly between the two
outermost brackets. Always position the brackets such that there
is no interference with the cords and/or mechanisms inside the
head rail. The procedure outlined below will assure proper bracket
placement.
Attaching the brackets:
The shape of head rails and mounting brackets varies by style of shade.
Lift the head rail into position such that the front edge of each
bracket is under the inner front edge of the head rail. Push the head
rail upward until the flexible tab at the bottom of each bracket snaps
onto the back of the head rail. Check carefully to assure that each
bracket is properly secured.

6
Lift the head rail into position such that the inner front edge of the
head rail slides into the slot at the front of each bracket. Push the
head rail upward until the flexible tab at the bottom of each bracket
snaps onto the back of the head rail. Check carefully to assure that
each bracket is properly secured.
For Outside Mounting:
Clip the brackets onto the head rail as described above. Hold the
shade level at the height desired and center it over the window
opening. Mark the exact location of each bracket with a pencil.
Remove the brackets from the head rail and position the top of each
bracket at the marked location and screw each bracket into the wall
or window molding using the 1
1
/8” screws, pre-drill the screw holes
using a 5/64" drill bit.
For Inside Mounting:
Clip the brackets onto the head rail as described above. Hold the
shade in place and make a pencil mark at the rear of each bracket
where it contacts the inside of the window frame. Remove the
brackets from the head rail and align them with the marks. Attach
each bracket using the 1
1
/8” screws, pre-drill the screw holes using a
5/64" drill bit.
Step 4. Attach Handle(s) [Applies to cordless shades only]
Attach the Handle to the bottom rail as illustrated. The handle is
designed to minimize contact with the shade fabric.
For TDBU cordless shades, attach the 2nd handle to the Middle Rail
as illustrated.

Semi
-Cell
Shades
Fabric
Cellular
&
7
Step 5. How to Operate
Standard Shade
To raise or lower the shade, pull the lift cords down and toward the
center of the shade to release the cord lock. Adjust the shade to the
desired height, and then move the lift cords toward the outside of
the shade to lock in place.
Top-Down Bottom-Up Shade
The cords on the right side of the shade control Bottom-Up/Down
function.
The cords on the left side control Top-Down/Up function.
Operate the cords as described above.
Semi-Cell & Sheer Roman 2-in-1 Shades
The cords on the right side of the shade control the Semi-Cell shade.
The cords on the left side control the Sheer Roman shade.
Operate the cords as described above.
Cordless Shade
Always raise and lower the shade SLOWLY(!) to assure that the
pleated fabric stacks neatly.
To lower the shade: grip the bottom-rail/handle and slowly pull
straight down.
To raise the shade: put one hand under the bottom rail (palm facing
up) and lift slowly until the desired height is reached.
Top-Down Bottom-Up Cordless Shade
To raise and lower the shade from the bottom, follow the directions
above.
To lower and raise the shade from the top: grip the middle rail handle
and slowly pull straight down/up.
Step 6. Installing Hold-Down Brackets
Hold down brackets are provided for optional use. These brackets
should be used only if the shade is to be in a permanently lowered
position. With the shade fully lowered, make pencil marks at the
outside ends of the bottom rail. Brackets should be lined up to the
pencil marks and screwed into place using the 1⁄2” screws. Insert
the pins protruding from the brackets into the holes on both ends of
the bottom rail (see illustration).

8
CLEANING
The vinyl head rail and bottom rail can be wiped clean with a damp
sponge. To clean the shade fabric, use a feather duster or vacuum
lightly using the soft brush attachment.
REPLACEMENT PARTS
In the event that replacement parts are ever needed, you may call:
1-800-933-7115
Please be sure to provide the following information, if possible:
• The complete model or catalog number of your product
• A description of the product
• A description of the part needed
LIMITED LIFETIME WARRANTY
The enclosed product is warranted to the original residential retail purchaser
as long as the product remains in the original window.
Covered:
Lifetime: Entire product against manufacturing defects (i.e. a flaw in the
product design, materials, or workmanship that causes the product to no
longer function)
5 years: All fabric
Not Covered:
Normal Wear and Tear
Any product that fails due to: • abuse • exposure to salt air • improper
installation • accident • extraordinary use • improper operation • alterations
• improper cleaning • misapplication • damage from pests/insects/pets •
improper handling • misuse
Costs associated with: • product removal • transportation to and from
the retailer • brand label removal • product re-measure • incidental or
consequential damages • product reinstallation • shipping
In the event there are multiple blinds/shades in the same room, only the
defective blind/shade will be replaced.
To Report Shipping Damage: If damage occurred during shipping, call place
of purchase and report within 7 calendar days or else you may be denied
credit for your damaged product.
To Obtain Service: If you suspect this product has a manufacturing defect
in materials or workmanship: 1. Locate the sales receipt 2. Call place of
purchase. Any unauthorized returns will not be accepted.
Warranty Remedy: THIS SHALL BE YOUR SOLE REMEDY UNDER THIS
LIMITED WARRANTY.
If this product is found to have a manufacturing defect in materials or
workmanship, we will (at our discretion) do one of the following:
• repair the product • replace the product • refund the cost of the product
Colors vary from lot to lot and may not exactly match sample swatch or
previous purchases.
Discontinued items or color selections will be replaced with the closest
equivalent current product.
YOUR RIGHTS UNDER STATE LAW:
This lifetime limited warranty gives you specific legal rights, and you may
have other rights, which vary from state to state. Some states do not allow
limitations on how long a warranty lasts, so the above limitations may not
apply to you. No agent, representative, dealer, or unauthorized employee has
the authority to increase or alter the obligation of this warranty. This lifetime
limited warranty supersedes any previous versions.
PHASE II PRODUCTS, INC.
501 WEST BROADWAY, SUITE 1350 • SAN DIEGO, CALIFORNIA 92101 • 1-800-264-1190