VISIONARY DESIGNS VK-1334 Manual

© 2016
www.classicexhibits.com
Order #XXXXX -
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-1334 - Layout
Plan View
10’
10’

© 2016
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2016
www.classicexhibits.com
Order #XXXXX -
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.



While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
General Information

© 2016
www.classicexhibits.com
Order #XXXXX -
Crate 1 of 1
Crate Packing - 1 of 1
Level 1 Level 2 Level 3 Level 4
Level 5 Level 6 Level 7 Level 8
Pedestal Shelf
36
9/9A
8/8A
Pedestal
Side Panels
Pedestal
Front & Back
Panels
Graphic Infils
Ceiling A
Pedestal
Counter Top
Workstation
Counter
Workstation
Counter
Workstation
Side Assembly
3, 4, 5 & 5A
Workstation
Side Assembly
3, 4, 5 & 5A
Backwall
Side Assembly
4, 5, 10, 11 & 11A
with assmebled
door
Backwall
Side Assembly
1, 2, 7 & 7A
Workstation
Side Assembly
1, 2, 5 & 5A
Workstation
Side Assembly
1, 2, 5 & 5A
Front Frame
Assembly
12, 13, 14, 14A 15 & 16
LT Reception Counter
Corner Pieces
1,3, 5 & 7
Ceiling B
6
Setup Hardware
Graphics
Large Monitor Mount

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 1 of 6
VK-1334 - Assembly
4
5
10
8
9
8
9
3
6
1
2
7
Item
1
2
3
4
5
6
7
8
9
10
Qty.
1
1
1
1
1
1
1
2
2
1
Description
95.5”h S44 Vertical Extrusion
95.5”h S44 Vertical Extrusion
95.5”h S44 Vertical Extrusion
95.5”h S44 Vertical Extrusion
95.5”h S44 Vertical Extrusion
95.5”h S44 Vertical Extrusion
22.25”w Z45 Horizontal Extrusion
45.2297”w Z45 Curved Horizontal Extrusion
31.5927”w Z45 Curved Horizontal Extrusion
Door Threshold
Steps:
1) Connect horizontal [7] between verticals [1] & [2].
2) Attach horizontal [8] between verticals [2] & [3].
3) Attach other horizontal [8] between verticals [3] & [4].
4) Install door threshold between verticals [4] & [5].
See Door Threshold detail.
5) Connect horizontal [9] between verticals [5] & [6].
6) Attach other horizontal [9] between verticals [1] & [6].
BACK SIDE
Door Threshold
Door Threshold
Tighten setscrew
to secure
Slide Connector
into Groove
of Extrusion
*
*
*

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 2 of 6
VK-1334 - Assembly Cont’d
4
5
8A
Infill
Infill
Door
Infill
Infill
Infill
Infill
9A
11A
11
8A
9A
3
6
1
2
7A
Item
7A
8A
9A
11/11A
Qty.
1
2
2
1/1
Description
22.25”w Z45 Horizontal Extrusion
45.2297”w Z45 Curved Horizontal Extrusion
31.5927”w Z45 Curved Horizontal Extrusion
22.25”w Z45 Horizontal Extrusion
Steps:
1) Insert infill between verticals [1] & [2] and secure in
place using horizontal [7A].
2) Repeat Step 1. to insert infills between verticals [2], [3] & [4]
and securing in place with horizontals [8A].
3) Attach horizontal [11] between verticals [4] & [5].
4) Insert infill between verticals [4] & [5] and secure in
place using horizontal [11A].
5) Install door to assembled frame where indicated.
See Door Instilation detail.
BACK SIDE
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
*
*

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 3 of 6
VK-1334 - Front Frame Assembly
12
13
14
14A
16
16
15
Item
12
13
14/14A
15
16
Qty.
1
1
1/1
1
2
Description
90”h TSP46 Vertical Extrusion
90”h TSP46 Vertical Extrusion
42”w TSP46 Horizontal Extrusion
86.417”h Z45 Vertical Extrusion
18.3128”w Z140 Horizontal Extrusion
Steps:
1) Attach horizontal [14] between verticals [12] & [13].
See TSP 46 Corner Connection detail.
2) Connect horizontal [14A] between verticals [12] & [13].
See TSP 46 Corner Connection detail.
3) Attach vertical [15] between horizontals [14] & [14A]
4) Attach horizontal [16] between verticals [12] & [15].
5) Repeat Step 4. for attaching other horizontal [16]
between [13] & [15].
6) Install standoff barrels on horizontals [16] for monitor mount.
See Stand-off Barrel & Bolt detail.
*
TSV1
Lock
Slide end of extrusion
over corner lock as shown.
Tighten setscrew
to secure extrusions
TSP 46 Corner Connection *
Attach standoff barrels to
vertical with threaded bolt.
Stand-Off Barrel & Bolt
Stand-Off
Barrel
**
**
*
*

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 4 of 6
VK-1334 - Ceiling & Front Frame
Steps:
1) Attach Ceilings to top of assembled frame using bolts from the top side.
2) Attach assembled front frame to assembled frame using standoff barrels.
See Vertical Extrusion to Post Attachment detail.
3) Apply SEG Graphic to front of frame.
See General Information Page for details.
3) Install Large Monitor Mount to front frame using standoff barrels.
See Large Monitor Mount Attachment detail.
*
*
*
*
Attach monitor mount to vertical extrusion
using standoff barrels, bolts and wing nuts.
*Large Monitor Mount Attachment
Bolt
Bolt
Monitor
Mount
Stand-Off
Barrel
Wing
Nut
Wing
Nut
V4
Vertical Extrusion to Post Attachment
*
Screw
Cap
Stand-off

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 5 of 6
MOD-1224 - Assembly
Item
1
2
3
4
5/5a
6
Qty
1
1
1
1
4/2
2
Description
37.5”h Vertical Extrusion
37.5”h Corner Extrusion
37.5”h Corner Extrusion
37.5”h Vertical Extrusion
11”w Horizontal Extrusion
24.875”w Horizontal Extrusion
Steps
1)
Connect side assemblies together using curved
extrusions [6], placing graphic infills between
horizontals as shown.
2) Place shelf atop lip of extrusions.
3) Set counter top atop assembled base.
Infill
When Assembled
1
2
3
4
5a
5
6
6
5
5a
5
5
Shelf
Counter
Extrusions 5a have
a lip for the
floor to rest
upon.
Lip for Shelf
Placement
Lip for Shelf
Placement
Lip
Extrusion Details:
Side assemblies highlighted in green
must stay assembled when shipping in cases

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 6 of 6
LT Reception Counter - Assembly
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
When assembled
Shelf
Countertop
Top View
Item
1
2
3
4
5
6
7
8
Description
38” 90° Connector
36.9738“ x 38” Curved Panel w/Door
38” 90° Connector
19“w x 38”h Side Panel
38” 90° Connector
44.13“w x 38” Side Panel
38” 90° Connector
19“w x 38”h Side Panel
Steps:
1) Assemble LT Panels in numerical order as shown.
2) Place Shelf into assembled counter.
3) Place Countertop onto assembled counter.
Place countertop
onto frame
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Lock Detail
Hole for lock
1 2
3 4