SelectBlinds Banded Fabric Loop Roller Shade User guide

BandedFabric
LoopRoller
Shade
owner's handbook

BandedFabric
LoopRoller
Shade
3
INSTALLATION INSTRUCTIONS
Step 1. Check Package Contents
Missing part? Call 800-264-1190
Mounting hardware kit includes the following:
Part Quantity
a.Mounting Brackets 2 for shades up to 45” wide
3 for shades up to 72” wide
b. Extension Brackets (for outside mounts) 2 for shades up to 45” wide
3 for shades up to 72” wide
c. Screws 4 for shades up to 45” wide
6 for shades up to 72” wide
d. Wall Anchors 4 for shades up to 45” wide
6 for shades up to 72” wide
Step 2. Tools required
Pencil, tape measure, level, screw driver, step stool, drill.
Step 3. Installation
Your blind may be installed either inside the window frame or outside
the window frame.
Wallboard or Plaster: use wall anchors.
Concrete, Stone, Brick: use a masonry drill bit and anchors or
screws specifically designed for masonry (not included).
Inside Mounting:
One bracket should be positioned about 2” to 6” from each end of
the head rail. For wider shades that require 3 or 4 brackets, these
should be spaced evenly between the two outermost brackets.
Attach each bracket to the inner top of the window opening using
the screws provided. Pre-drill the screw holes using a 5/64" drill bit.
The extension brackets are not used for inside mounts.
For flush inside mounts, attach the brackets to the head rail first (see
drawings and attachment instructions below), and then position the
shade in the window opening as desired. Then make pencil marks at
the back of each bracket. Remove the brackets by pressing on the
plastic tab. Align the brackets with the pencil marks, and then screw
them in place as described above.
Outside Mounting:
Attach the Extension Brackets to the wall or window framing. One
bracket should be positioned about 2” to 6” from each end of the
head rail. For wider shades that require 3 or 4 brackets, these should
be spaced evenly between the two outermost brackets. Pre-drill the
screw holes using a 5/64" drill bit.

4
The brackets must be level – use a Spirit Level if necessary to assure
proper alignment.
Then attach a Mounting Bracket to each Extension Bracket using the
nut and bolt pre-attached to each Extension Bracket.
To adjust head rail extension, remove the shade from the mounting
brackets by pressing on the plastic tabs at the front of each bracket.
Then loosen the nut and bolt, and move the mounting brackets
forward or backward as preferred.
Step 4. Securing the Head Rail
Slide the inner rear of the head rail onto the metal tabs at the back of
the brackets, and then push up to lock the head rail in place. Check
carefully to assure that each bracket is properly secured.
Step 5. Attach the Safety Cord Guide
The cord guide must be attached per these instructions in order for
your shade to function properly.
Install Mounting Bracket:
Determine which direction the mounting bracket will face relative to
the Tension Device. Make sure the Tension Device will be snapped
into the mounting stand in the same correct direction. Before
attaching Tension Device to the base, measure and mark the
location in the window where the tension device will be mounted.
Mount the base in position without the tension device attached.
Position the Tension Device on the window frame or the wall so
that the Tension Device and control cord/chain does not interfere
with raising or lowering the shade. The Tension Device should be
installed so that cord/bead chain hangs loosely – do not stretch
or pull down on it. Stretching the cord/bead chain will cause
excessive wear. Do not twist or cross the control cord/bead
chain. In order to position the base properly, adjust the cord so
that the Cord Guide is at the bottom of the cord loop and let it
hang freely. Hold the tension device and the bracket against the

BandedFabric
LoopRoller
Shade
5
window frame or wall and mark the position of the bracket (mark
the location of the screw holes) with a pencil. Insert and secure two
screws through the holes in the mounting bracket. The mounting
screws must be secured into a solid surface or wall anchors.
On inside mount shades the Tension Device may be mounted to the
side window frame or when the treatment spans beyond the window
frame it may be mounted to the wall.
Mate Tension Device To Mounting Bracket:
Once the tension device is snapped to the base it is designed not to
be removed.
Press center round button exposing the four latching legs and press
into the corresponding thru-hole of the mounting bracket stand until
the latches snap and lock to the mounting stand. The loop should
now pass freely through the Tension Device.
Step 6. How to Operate
To raise or lower the shade, pull the lift cord.
Cleaning
To clean the shade fabric, use a feather duster or vacuum lightly
using the soft brush or upholstery attachment. For spot cleaning, use
warm (not hot!) water with a mild soap to damp clean.
REPLACEMENT PARTS
In the event that replacement parts are ever needed,
you may call: 1-800-264-1190
Please be sure to provide the following information, if possible:
• The complete model or catalog number of your product
• A description of the product
• A description of the part needed

6

BandedFabric
LoopRoller
Shade
7
LIMITED LIFETIME WARRANTY
The enclosed product is warranted to the original residential retail
purchaseras long as the product remains in the original window.
Covered:
Lifetime: Entire product against manufacturing defects (i.e. a flaw in the
product design, materials, or workmanship that causes the product
to no longer function)
3 years: Cords including internal cords such as those found in cordless
blinds. 5 years: All fabric
Not Covered:
Normal Wear and Tear
Any product that fails due to: abuse • exposure to salt air • improper
installation • accident • extraordinary use • improper operation •
alterations • improper cleaning • misapplication • damage from pests/
insects/pets • improper handling • misuse.
Natural wood products that have: loss of color intensity • yellowing or
cracking of plastic parts or foam wood product • variations in color,
grain, or texture • warping of wood slats in high humidity areas.
Costs associated with: product removal • transportation to and from
the retailer • brand label removal • product remeasure • incidental or
consequential damages • product reinstallation • shipping.
In the event there are multiple blinds/shades in the same room, only the
defective blind/shade will be replaced.
To Report Shipping Damage:
If damage occurred during shipping, call place of purchase and
report within 7 calendar days or else you may be denied credit for
your damaged product.
To Obtain Service:
If you suspect this product has a manufacturing defect in materials or
workmanship:
1. Locate the sales receipt
2. Call place of purchase
Any unauthorized returns will not be accepted.
Warranty Remedy:
THIS SHALL BE YOUR SOLE REMEDY UNDER THIS LIMITED
WARRANTY.
If this product is found to have a manufacturing defect in materials or
workmanship, we will (at our discretion) do one of the following
• repair the product
• replace the product
• refund the cost of the product
Colors vary from lot to lot and may not exactly match sample swatch or
previous purchases. Discontinued items or color selections will be
replaced with the closest equivalent current product.
YOUR RIGHTS UNDER STATE LAW:
This lifetime limited warranty gives you specific legal rights, and you
may have other rights, which vary from state to state. Some states
do not allow limitations on how long a warranty lasts, so the above
limitations may not apply to you.
No agent, representative, dealer, or unauthorized employee has the
authority to increase or alter the obligation of this warranty. This lifetime
limited warranty supersedes any previous versions.

8