SelectBlinds Cordless Honeycomb Shades Manual

HONEYCOMB SHADES
Corded & Corded Top Down Bottom Up
Thank you for your purchase. This shade has been custom built for you from the highest quality
materials. To avoid errors and save valuable time, please read these instructions before installing your
new shades.
1. Pencil or Marker
2. Measuring Tape
3. Phillips Screwdriver
4. Carpenter’s Level
5. Power Drill
6. Mounting Fasteners
7. 3/32” Drill Bit & 1/4” Hex Nut Driver Bit
1
Getting Started ................................................................................................................................................................................................ Page 2
Mounting Type ................................................................................................................................................................................................. Page 2
Bracket Installation .......................................................................................................................................................................................... Page 2
Inside Mount .................................................................................................................................................................................................... Page 3
Outside Mount ................................................................................................................................................................................................. Page 3
Side Mount ...................................................................................................................................................................................................... Page 3
Installing the Shade ......................................................................................................................................................................................... Page 4
Adjusting the Shade ......................................................................................................................................................................................... Page 4
Installing Hold Down Brackets (Outside Mount Only) ...................................................................................................................................... Page 4
Cordlock Operation .......................................................................................................................................................................................... Page 5
Cord Cleats ...................................................................................................................................................................................................... Page 5
Care and Cleaning ........................................................................................................................................................................................... Page 5
Child Safety ..................................................................................................................................................................................................... Page 6
Warranty Information ....................................................................................................................................................................................... Page 6
Mounting Surface Fastener
Drywall, Plaster Wall Anchors, Expansion Bolts
(Not provided)
Metal Sheet Metal Screws
(Not provided)
Wood No. 6 Hex Head Screws
(Provided)
INSTALLATION & OPERATING INSTRUCTIONS
TOOLS YOU WILL NEED
TABLE OF CONTENTS

2
All of the required installation components are wrapped in your package along with these instructions. Check that the parts you have correspond to
the parts shown below.
NOTE: Some parts may vary depending upon your chosen mounting options.
Installation brackets may be used for INSIDE or OUTSIDE mounts.
Mounting the brackets level is essential for proper operation of the shade. Shim the brackets if necessary to achieve a level alignment.
The bracket requirements and placements are the same for inside and outside mounts. Refer to the following spacing diagram and bracket
requirement chart.
Installation Bracket Requirement Chart
Shade Width Brackets Required
12” to 31” 2
31-1/8” - 72” 3
If the installation brackets are mounted correctly, the rest of the installation process will follow easily. To prepare for this important rst step, review the
mounting types and basic window terminology illustrated below.
Bottom Sill
Top Sill
Jamb Jamb
Collectively, the sills and
jambs are called the
“window casement”.
Molding
Inside Mount
Shade ts within
window opening.
Outside Mount
Shade mounts outside
window opening.
Mounting Types
Installation
Brackets
Extension Bracket
(optional)
Spacer Blocks
(optional)
Side Mount Bracket
(optional)
3” Space Evenly Space Evenly 3”
Installation Brackets
GETTING STARTED
Bracket Installation

3
For inside mounts the installation brackets will be screwed in place through the top two hole of each bracket.
Refer to the depth requirements chart:
NOTE: Prior to mounting the brackets, add any clearance depth
required to avoid obstructions such as window cranks or handles.
ATTACH THE BRACKETS
1. Screw the bracket through top two holes to desired window sill location.
• Use a 3/32” drill bit to drill holes for the screws.
2. Ensure all brackets are level and aligned.
IMPORTANT: If you are fastening the installation brackets to drywall, be sure to use wall anchors and follow the instructions provided
with the anchors. (Anchors not provided.)
Minimum Depth Fully Recessed
1” 2-1/2”
For outside mounts the installation brackets will be screwed in place through the two back holes of each bracket.
Refer to the minimum surface height chart.
ATTACH THE BRACKETS
1. Screw the bracket through top two holes to desired window sill location.
• Use a 3/32” drill bit to drill holes for the screws.
2. Ensure all brackets are level and aligned.
IMPORTANT: If you are fastening the installation brackets to drywall, be sure to use wall anchors
and follow the instructions provided with the anchors. (Anchors not provided.)
SPACER BLOCKS (optional)
1. Spacer blocks will be attached to the end of each bracket.
2. Ensure the screws are long enough to secure brackets to surface.
3. Do not use more than three spacer bocks per bracket.
4. If installing extension brackets, do not use spacer blocks.
EXTENSION BRACKETS (optional)
1. Position the extension brackets to the desired wall location.
2. The bracket tops must be aligned and level to one another.
3. Mount the extension brackets through the back holes with two screws.
4. Attach the installation brackets to the extension brackets.
Minimum Height
3/4”
1. Align the bracket top with the desired height of the top of the head rail. Mark holes for screws,
remove brackets and drill holes.
2. Insert screws for keyhole slots only. Approximately 1/8” of the screw should be left protruding.
3. Pull the end cap out of the headrail and slide the bracket on as show. Replace the end cap and then
slide the bracket all the way into the headrail.
Install the second bracket in the same manner as the rst bracket.
Hook one bracket onto the screw in the window frame, using the keyhole slot. Bring the other end bracket over
the screw at the other side of the frame. Slide down, exing bracket inward until the screw engages
in the keyhole slot.
Make sure both brackets are slipped down all the way in the keyhole slot so that the screw is in the top portion
of the keyhole slot. Install a screw in the bottom hole of each bracket. Tighten all screws.
2-1/2”
2-1/2”
2-1/2”
3/4” Minimum
Installation brackets attached to extension
brackets with the included screws and nuts.
Use the same holes for all brackets to
ensure even projection from the surface.
Extension
Brackets
Keyhole
Slot
Inside Mount
Outside Mount
Side Mount

MOUNT THE HEADRAIL
1. Hold the shade up near the brackets and insert the front clip of the bracket into the front groove of the rail.
2. Make sure the shade is centered in the window opening.
3. Push the rail back and up until the back clips of the bracket are inserted in the back of the rail.
To REMOVE shade, reverse procedure. As you release the brackets, support the head rail to keep it from falling.
4
1. Raise and lower the shade several times.
2. If the length is incorrect or the bottom rail is not level, use the following steps to correct.
BOTTOM RAIL SHADE ADJUSTMENT
1. Lift bottomrail on the side to be adjusted. This will take the weight off the cord.
2. Use a screwdriver or dime.
• Turn screw clockwise to lift that side of the shade.
• Turn screw counter clockwise to lower that side of the shade.
• Half a revolution is 1/4” adjustment (maximum adjustment is 1/2”).
INTERMEDIATE RAIL SHADE ADJUSTMENT
1. Lift intermediate rail on side to be adjusted. This will take the weight off the cord.
2. Use a screwdriver or dime.
• Turn screw clockwise to lift that side of the rail.
• Turn screw counter clockwise to lower that side of the rail.
• Half a revolution is 1/4” adjustment (maximum adjustment is 1/2”).
ATTACH THE (optional) HOLD DOWN BRACKETS:
1. Lower the shade and place the hold down pins into the bottom rail end caps.
2. Mark the hold down bracket locations on the mounting surface.
3. With the brackets level, attach them using two screws.
Installing the Shade Removing the Shade
Installing the Shade
Adjusting the Shade
Installing Hold Down Brackets (Outside Mount Only)

5
BOTTOM UP ONLY
• To lower or release shade, pull the cord inward toward the center of the shade.
• To raise or lock the shade, pull the cord straight down and outward toward the edge of the shade.
TOP DOWN - BOTTOM UP
On a standard top down - bottom up, the right hand cord operates the middle rail, while the left hand cord
operates the bottom rail.
• To lower or release either the middle rail or bottom rail of the shade, pull the cord inward toward the center of the shade
• To raise or lock either the middle rail or bottom rail of the shade, pull the cord straight down and outward toward the edge of the shade.
Note: Before raising the middle rail all the way to the head rail, you should raise the bottom rail a couple of inches. This will prevent pinching the
equalizer between the rails.
Be aware that it is possible for children to strangle in window covering cords. To reduce the occurrence of an accident, all cords
must be kept out of reach of children, including infants. Cord cleats are an effective way to implement this essential precaution.
• Mount the cord cleat at a safe height, taking into account furniture or other objects upon which a child may climb.
• Then, after each use of the shade, simply wrap the excess cord around the cleat. It’s fast, easy and safe.
To protect your children, we are pleased to provide cord cleats free of charge upon request.
Honeycomb shades are made of an anti-static, dust resistant fabric which repels dirt and dust. For most of these fabrics, the following options are
available if your shade needs cleaning.
DUSTING: Regular light dusting with a feather duster is all the cleaning that is needed in most circumstances.
VACUUMING: Use a hand-held vacuum with low suction for more thorough dust removal.
SPOT CLEANING: Use the following steps for spot cleaning: (1) Prepare a solution of warm water and mild dishwashing detergent. (2) Dampen a
clean cloth in the solution and ring it out. (3) Dab the spot with the dampened cloth until it is gone. DO NOT RUB THE FABRIC. (4) Allow the shade
to dry in the completely lowered position.
CAUTION: Avoid creasing Blackout fabrics during cleaning.
DEEP CLEANING: Use the following steps for deep cleaning: (1) Immerse shade in basin or bathtub lled with warm water and mild detergent.
(2) Rinse with clean water. (3) Fully raise shade and tilt to eliminate excess water, (4) Reinstall damp shade, lower it, and let it dry completely.
CAUTION: Do not immerse Blackout fabrics. Do not immerse Cordless Lift & Lock bottomrail in water.
ULTRASONIC CLEANING: Standard shades, except those made with Blackout or Blackout Lining can be ultrasonically cleaned by a professional.
• Specify that a mild detergent be used.
• Never immerse the headrail in the solution.
• Dry the shade completely in the lowered position.
CAUTION: Do not ultrasonically clean Blackout fabrics. Do not immerse headrail in water.
Cordlock Operation
Cord Cleats
CARE AND CLEANING

SAFETY LABELS
In compliance with WCMA/ANSI safety standards the warning labels on the bottom rail are designed to be permanent. DO NOT remove the permanent
warning label on the bottom rail. This assures that future owners of this product will be aware of potential dangers associated with this shade.
To further reduce hazards, this shade was built with a cord connector which was designed to break apart when force is applied from the top.
If your cord connector should happen to break apart, follow the instructions below to reassemble:
1. When the connector is open, each side has a cord coming in
at the top, one side has a cord coming in from the bottom.
2. Fit the Bottom edges together. The side with the cord ts into
the side without the cord.
3. Swing the top ends together and press in the middle to fully connect.
1022090 • rev 12/2020
Lifetime Limited Warranty covering our Custom Made Blinds
We extend this lifetime limited warranty to the original purchaser. This warranty applies only to manually operated Custom Products properly installed
in the window, door or interior area for which they were intended. Installation of the product must be in accordance with accompanying instructions.
The product cannot be modied. It is the purchaser’s responsibility to maintain and clean the product in compliance with the instruction provided.
The product must be used only in the window for which it was purchased. Damage to the product resulting from misuse, abuse, direct exposure to
salty air or discoloration due to sunlight or the passage of time is not covered by this warranty.
This warranty does not apply to conditions caused by normal wear and tear upon the product. This warranty is exclusive and in lieu of all other
obligations, liabilities or warranties. In no event shall the Manufacturer be liable for incidental or consequential damages or for any other direct or
indirect damage, loss, cost, expense or fee. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this
exclusion or limitation may not apply to you.
In the event of a defect under this warranty, we will repair or replace the product, at our option, provided it is returned to our store. Our warranty
obligation excludes shipping charges and labor costs for measuring and installation. Repairs will be made with like or similar parts. This warranty
gives you specic legal rights, and you may have other rights which vary from state to state.
Notes: Motorization Systems are warranted for ve years from the date of purchase. Specialty Blinds and Shades are warranted for one year from
the date of purchase.
This warranty does not apply to Commercial Orders.
6
Breakthrough
Cord Connector
Young children can STRANGLE in cord loops and in the loop above the cord stop. They can also wrap cords around their necks and STRANGLE.
■Always keep cords out of children’s reach.
■Move cribs, playpens and other furniture away from cords.
Children can climb furniture to get to cords.
■Do not tie cords together.
■Make sure cords do not twist together and create a loop.
Window Blind Cord Can STRANGLE
Your Child.
To prevent strangulation, purchase cordless
products or products with inaccessible cords.
5.1.3
La cuerda de la persiana puede ESTRANGULAR a su
niño. Para evitar el estrangulamiento, compre
alternativas cuerda o productos con cuerdas
inaccesibles.
Rev. 5/18 Print 5/18
WARNING/ADVERTENCIA
CHILD SAFETY
WARRANTY INFORMATION

HONEYCOMB SHADES
Cordless Lift & Lock
Cordless Lift & Lock Top Down Bottom Up
Thank you for your purchase. This shade has been custom built for you from the highest quality
materials. To avoid errors and save valuable time, please read these instructions before installing your
new shades.
1. Pencil or Marker
2. Measuring Tape
3. Phillips Screwdriver
4. Carpenter’s Level
5. Power Drill
6. Mounting Fasteners
7. 3/32” Drill Bit & 1/4” Hex Nut Driver Bit
1
Getting Started ................................................................................................................................................................................................ Page 2
Mounting Type ................................................................................................................................................................................................. Page 2
Bracket Installation .......................................................................................................................................................................................... Page 2
Inside Mount .................................................................................................................................................................................................... Page 3
Outside Mount ................................................................................................................................................................................................. Page 3
Side Mount ...................................................................................................................................................................................................... Page 3
Installing the Shade ......................................................................................................................................................................................... Page 4
Operating the Shade ........................................................................................................................................................................................ Page 4
Adjusting the Shade ...................................................................................................................................................................................... Page 4-5
Care and Cleaning ........................................................................................................................................................................................... Page 5
Child Safety ..................................................................................................................................................................................................... Page 6
Warranty Information ....................................................................................................................................................................................... Page 6
Mounting Surface Fastener
Drywall, Plaster Wall Anchors, Expansion Bolts
(Not provided)
Metal Sheet Metal Screws
(Not provided)
Wood No. 6 Hex Head Screws
(Provided)
INSTALLATION & OPERATING INSTRUCTIONS
TOOLS YOU WILL NEED
TABLE OF CONTENTS

2
All of the required installation components are wrapped in your package along with these instructions. Check that the parts you have correspond to
the parts shown below.
NOTE: Some parts may vary depending upon your chosen mounting options.
Installation brackets may be used for INSIDE or OUTSIDE mounts.
Mounting the brackets level is essential for proper operation of the shade. Shim the brackets if necessary to achieve a level alignment.
The bracket requirements and placements are the same for inside and outside mounts. Refer to the following spacing diagram and bracket
requirement chart.
Installation Bracket Requirement Chart
Shade Width Brackets Required
12” to 31” 2
31-1/8” to 72” 3
72-1/8” to 84” 4
If the installation brackets are mounted correctly, the rest of the installation process will follow easily. To prepare for this important rst step, review the
mounting types and basic window terminology illustrated below.
Bottom Sill
Top Sill
Jamb Jamb
Collectively, the sills and
jambs are called the
“window casement”.
Molding
Inside Mount
Shade ts within
window opening.
Outside Mount
Shade mounts outside
window opening.
Mounting Types
Installation
Brackets
Extension Bracket
(optional)
Spacer Blocks
(optional)
Side Mount Bracket
(optional)
3” Space Evenly Space Evenly 3”
Installation Brackets
GETTING STARTED
Bracket Installation

3
For inside mounts the installation brackets will be screwed in place through the top two holes of each bracket.
Refer to the depth requirements chart:
NOTE: Prior to mounting the brackets, add any clearance depth
required to avoid obstructions such as window cranks or handles.
ATTACH THE BRACKETS
1. Screw the bracket through top two holes to desired window sill location.
• Use a 3/32” drill bit to drill holes for the screws.
2. Ensure all brackets are level and aligned.
IMPORTANT: If you are fastening the installation brackets to drywall, be sure to use wall anchors and follow the instructions provided
with the anchors. (Anchors not provided.)
Minimum Depth Fully Recessed
1” 2-1/2”
For outside mounts the installation brackets will be screwed in place through the two back holes of each bracket.
Refer to the minimum surface height chart.
ATTACH THE BRACKETS
1. Screw the bracket through back two holes to desired location.
• Use a 3/32” drill bit to drill holes for the screws.
2. Ensure all brackets are level and aligned.
IMPORTANT: If you are fastening the installation brackets to drywall, be sure to use wall anchors
and follow the instructions provided with the anchors. (Anchors not provided.)
SPACER BLOCKS (optional)
1. Spacer blocks will be attached to the end of each bracket.
2. Ensure the screws are long enough to secure brackets to surface.
3. Do not use more than three spacer bocks per bracket.
4. If installing extension brackets, do not use spacer blocks.
EXTENSION BRACKETS (optional)
1. Position the extension brackets to the desired wall location.
2. The bracket tops must be aligned and level to one another.
3. Mount the extension brackets through the back holes with two screws.
4. Attach the installation brackets to the extension brackets.
Minimum Height
3/4”
1. Align the bracket top with the desired height of the top of the head rail. Mark holes for screws,
remove brackets and drill holes.
2. Insert screws for keyhole slots only. Approximately 1/8” of the screw should be left protruding.
3. Pull the end cap out of the headrail and slide the bracket on as shown. Replace the end cap and
then slide the bracket all the way into the headrail.
Install the second bracket in the same manner as the rst bracket.
Hook one bracket onto the screw in the window frame, using the keyhole slot. Bring the other end bracket over
the screw at the other side of the frame. Slide down, exing bracket inward until the screw engages
in the keyhole slot.
Make sure both brackets are slipped down all the way in the keyhole slot so that the screw is in the top portion
of the keyhole slot. Install a screw in the bottom hole of each bracket. Tighten all screws.
2-1/2”
2-1/2”
2-1/2”
3/4” Minimum
Installation brackets attached to extension
brackets with the included screws and nuts.
Use the same holes for all brackets to
ensure even projection from the surface.
Extension
Brackets
Keyhole
Slot
Inside Mount
Outside Mount
Side Mount

MOUNT THE HEADRAIL
1. Hold the shade up near the brackets and insert the front clip of the bracket into the front groove of the rail.
2. Make sure the shade is centered in the window opening.
3. Push the rail back and up until the back clips of the bracket are inserted in the back of the rail.
To REMOVE shade, reverse procedure. As you release the brackets, support the head rail to keep it from falling.
4
1. Raise and lower the shade several times.
2. If the length is incorrect or the bottom rail is not level, use the following steps to correct.
BOTTOM-UP BOTTOMRAIL AND TOP-DOWN/BOTTOM-UP
INTERMEDIATE RAIL SHADE ADJUSTMENT
1. Lift bottomrail on the side to be adjusted. This will take the weight off the cord.
2. Use a screwdriver or dime.
• Turn screw clockwise to lift that side of the shade.
• Turn screw counter clockwise to lower that side of the shade.
• Half a revolution is 1/4” adjustment (maximum adjustment is 1/2”).
TO RAISE AND LOWER THE CORDLESS LIFT & LOCK SHADE
1. Push and hold the button on the bottomrail handle.
2. Raise or lower the shade to the desired position.
3. Release the button to lock the shade into place.
Installing the Shade Removing the Shade
Installing the Shade
Adjusting the Shade
Operating the Shade

5
Honeycomb shades are made of an anti-static, dust resistant fabric which repels dirt and dust. For most of these fabrics, the following options are
available if your shade needs cleaning.
DUSTING: Regular light dusting with a feather duster is all the cleaning that is needed in most circumstances.
VACUUMING: Use a hand-held vacuum with low suction for more thorough dust removal.
SPOT CLEANING: Use the following steps for spot cleaning: (1) Prepare a solution of warm water and mild dishwashing detergent. (2) Dampen a
clean cloth in the solution and ring it out. (3) Dab the spot with the dampened cloth until it is gone. DO NOT RUB THE FABRIC. (4) Allow the shade
to dry in the completely lowered position.
CAUTION: Avoid creasing Blackout fabrics during cleaning.
DEEP CLEANING: Use the following steps for deep cleaning: (1) Immerse shade in basin or bathtub lled with warm water and mild detergent.
(2) Rinse with clean water. (3) Fully raise shade and tilt to eliminate excess water, (4) Reinstall damp shade, lower it, and let it dry completely.
CAUTION: Do not immerse Blackout fabrics. Do not immerse Cordless Lift & Lock bottomrail in water.
ULTRASONIC CLEANING: Standard shades, except those made with Blackout or Blackout Lining, can be ultrasonically cleaned by a professional.
• Specify that a mild detergent be used.
• Never immerse the headrail in the solution.
• Dry the shade completely in the lowered position.
CAUTION: Do not ultrasonically clean Blackout fabrics. Do not immerse headrail in water.
TOP-DOWN/BOTTOM-UP BOTTOMRAIL SHADE ADJUSTMENT
1. Remove right end cap of the bottomrail
2. Remove the small, white plastic tool located inside the bottomrail
3. Find the plastic dial just to the right of where the tool was positioned
• Using the tool to depress the dial about 1/4”
• Turn clockwise to lower the bottomrail
• Turn counterclockwise to raise raise the bottomrail
• When shade has been adjusted to the desired level remove the tool from the dial
and insert it back into the bottomrail
4. Replace end cap.
NOTE: If the tool gets misplaced a athead screwdriver may be used.
CARE AND CLEANING
Adjusting the Shade

SAFETY LABELS
In compliance with WCMA/ANSI safety standards the warning labels on the bottom rail are designed to be permanent. DO NOT remove the permanent
warning label on the bottom rail. This assures that future owners of this product will be aware of potential dangers associated with this shade.
C8-20-4402 • rev 1/2021
Lifetime Limited Warranty covering our Custom Made Blinds
We extend this lifetime limited warranty to the original purchaser. This warranty applies only to manually operated Custom Products properly installed
in the window, door or interior area for which they were intended. Installation of the product must be in accordance with accompanying instructions.
The product cannot be modied. It is the purchaser’s responsibility to maintain and clean the product in compliance with the instruction provided.
The product must be used only in the window for which it was purchased. Damage to the product resulting from misuse, abuse, direct exposure to
salty air or discoloration due to sunlight or the passage of time is not covered by this warranty.
This warranty does not apply to conditions caused by normal wear and tear upon the product. This warranty is exclusive and in lieu of all other
obligations, liabilities or warranties. In no event shall the Manufacturer be liable for incidental or consequential damages or for any other direct or
indirect damage, loss, cost, expense or fee. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this
exclusion or limitation may not apply to you.
In the event of a defect under this warranty, we will repair or replace the product, at our option, provided it is returned to our store. Our warranty
obligation excludes shipping charges and labor costs for measuring and installation. Repairs will be made with like or similar parts. This warranty
gives you specic legal rights, and you may have other rights which vary from state to state.
Notes: Motorization Systems are warranted for ve years from the date of purchase. Specialty Blinds and Shades are warranted for one year from
the date of purchase.
This warranty does not apply to Commercial Orders.
6
Young children can STRANGLE in cord loops and in the loop above the cord stop. They can also wrap cords around their necks and STRANGLE.
■Always keep cords out of children’s reach.
■Move cribs, playpens and other furniture away from cords.
Children can climb furniture to get to cords.
■Do not tie cords together.
■Make sure cords do not twist together and create a loop.
Window Blind Cord Can STRANGLE
Your Child.
To prevent strangulation, purchase cordless
products or products with inaccessible cords.
5.1.3
La cuerda de la persiana puede ESTRANGULAR a su
niño. Para evitar el estrangulamiento, compre
alternativas cuerda o productos con cuerdas
inaccesibles.
Rev. 5/18 Print 5/18
WARNING/ADVERTENCIA
CHILD SAFETY
WARRANTY INFORMATION

HONEYCOMB SHADES
Continuous Cord Loop
Thank you for your purchase. This shade has been custom built for you from the highest quality
materials. To avoid errors and save valuable time, please read these instructions before installing
your new shades
1. Pencil or Marker
2. Measuring Tape
3. Phillips Screwdriver
4. Carpenter’s Level
5. Power Drill
6. Mounting Fasteners
7. 3/32” Drill Bit & 1/4” Hex Nut Driver Bit
1
Getting Started ................................................................................................................................................................................................ Page 2
Mounting Type ................................................................................................................................................................................................. Page 2
Bracket Installation .......................................................................................................................................................................................... Page 2
Motorized Shades ............................................................................................................................................................................................ Page 3
Inside Mount .................................................................................................................................................................................................... Page 3
Outside Mount ................................................................................................................................................................................................. Page 3
Installing the Shade ......................................................................................................................................................................................... Page 4
Installing the Cord Tensioner ........................................................................................................................................................................... Page 4
Attaching Hold-Down Brackets (optional) ........................................................................................................................................................ Page 4
Operating the Shade ........................................................................................................................................................................................ Page 5
Adjusting the Shade ......................................................................................................................................................................................... Page 5
Troubleshooting ............................................................................................................................................................................................... Page 6
Care and Cleaning ........................................................................................................................................................................................... Page 6
Child Safety ..................................................................................................................................................................................................... Page 7
Warranty Information ....................................................................................................................................................................................... Page 7
Mounting Surface Fastener
Drywall, Plaster Wall Anchors, Expansion Bolts
(Not provided)
Metal Sheet Metal Screws
(Not provided)
Wood No. 6 Hex Head Screws
(Provided)
INSTALLATION INSTRUCTIONS
TOOLS YOU WILL NEED
TABLE OF CONTENTS

2
Thank you for purchasing this Honeycomb Shade. All of the required installation components are wrapped in your package along with these instructions.
With proper installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction booklet
before beginning the installation. Check that the parts you have correspond to the parts shown below.
Note: Some parts may vary depending upon your chosen shade system or mounting option.
The installation brackets may be for INSIDE or OUTSIDE mounts.
Mounting the brackets level is essential for proper operation of the shade.
Shim the brackets if necessary to achieve a level alignment.
The bracket requirements and placements are the same for inside and outside mounts.
Refer to the following spacing diagram and bracket requirement chart.
When installing motorized shades with an external battery pack refer to the chart below:
NOTE: Extension Brackets required for External Battery - Mounted to the back of the headrail.
Shade Width Brackets Required
18” to 38” 2
38-1/8” to 72” 3
72-1/8” to 106” 4
106-1/8” to 140” 5
140-1/8” to 174” 6
If the installation brackets are mounted correctly, the rest of the installation process will follow easily. To prepare for this important rst step, review the
mounting types and basic window terminology illustrated below.
Installation
Brackets
Clear Plastic Insert
— if ordered
Cordless Lift Handle
(Clear or Color Coordinated)
Extension
Bracket
(optional)
Spacer Blocks
(optional)
Cord Tensioner Bracket
& Instruction Pack
(Cord Loop Shades Only)
Hold Down
Brackets
(optional)
Bottom Sill
Top Sill
Jamb Jamb
Collectively, the sills and
jambs are called the
“window casement”.
Molding
Inside Mount
Shade ts within
window opening.
Outside Mount
Shade mounts outside
window opening.
Cordless Lift Shade Only
Inside (IB) Mount
Minimum mounting depth 3/4”
Minimum mounting depth, ush mount 2-1/8”
Outside (OB) Mount
Minimum at vertical surface 1-1/2”
External Battery - Mounted away from the Headrail
Inside (OB) Mount
Minimum mounting depth 2-5/8”
Minimum mounting depth, ush mount 3-1/4”
Outside (OB) Mount
Minimum at vertical surface 1-1/2”
External Battery - Mounted to the back from the Headrail*
Honeycomb & Hybrid PleatHoneycomb & Hybrid Pleat
GETTING STARTED
Bracket Installation
Mounting Types

For inside mounts the installation brackets will be screwed in place through the top two holes of each bracket.
Refer to the mounting depth chart:
NOTE: Prior to mounting the brackets, add any clearance depth required to avoid obstructions such as window cranks or handles.
ATTACH THE BRACKETS:
1. Screw installation brackets through top two holes to desired window sill location.
• Use a 3/32” drill bit to drill holes for the screws.
2. Ensure all brackets are level and aligned.
IMPORTANT: If you are fastening the installation brackets to drywall, be sure to use wall anchors
and follow the instructions provided with the anchors. (Anchors not provided.)
For outside mounts the standard installation brackets will be screwed in place through the two back holes of each bracket.
Refer to the minimum surface height chart:
ATTACH THE BRACKETS:
1. Screw standard brackets through two back holes to desired location.
• Use a 3/32” drill bit to drill holes for the screws.
2. Ensure all brackets are level and aligned.
IMPORTANT: If you are fastening the installation brackets to drywall, be sure to use wall anchors
and follow the instructions provided with the anchors. (Anchors not provided.)
EXTENSION BRACKETS (optional):
1. Position the extension brackets to the desired wall location.
2. The bracket tops must be aligned and level to one another.
3. Mount the extension brackets through the back holes with two screws.
4. Attach installation brackets to extension brackets with included screws & nuts.
NOTE: Use the same holes for all brackets to ensure even projection from the surface.
SIDE MOUNT WITH EXTENSION BRACKETS (optional):
1. Measure from window sill up to desired mounting position on each side of the window frame.
2. Mark position.
3. Mount Extension Brackets on each side of window frame, as shown. Make sure to conrm
that the headrail will sit perfectly level.
4. Once the Extension Brackets are installed and properly positioned, attach the mounting
brackets using the nuts and bolts provided.
3
Prior to installing the shade, attach the external battery pack to the motor and pair the motor with the remote using the instructions included with the remote.
Nut
Extension
Bracket
Mounting
Bracket
Bolt
Minimum Depth Fully Recessed
3/4” 2-1/8”
Minimum Height
1-1/2”
Inside Mount
Outside Mount
Motorized Shades

FOR MOTORIZED SHADES (ONLY)
IMPORTANT: For Motorized shades only, make sure the remote control is paired to the motor prior to installing in the window.
FOR CORDLESS LIFT SHADES (ONLY)
NOTE: The cordless lift handle should be installed prior to mounting the shade in the window.
• The shade will come with the color coordinated textured handle pre-inserted into the moving rail(s).
• If desired, a clear textured handle or a clear plastic insert are available and must be selected at
the time the order is placed.
NOTE: The plastic handle is not easily removable. Should it become necessary to remove the handle
please contact customer service.
MOUNTING THE HEADRAIL
• With the front side of the shade facing you, tilt the headrail slightly backward
to angle the front inside lip to the brackets.
• Rotate headrail back and upward to snap in it into place.
FOR CONTINUOUS CORD LOOP SHADES (ONLY)
Before doing anything, you must rst slide the cord tensioner to the bottom of the cord loop.
• Insert a small screwdriver, punch, or awl through the screw hole at the bottom of the cord tensioner.
• Move the screw hole down to the indicator line to release the safety mechanism.
WARNING: It is imperative that the cord tensioner be properly secured to the wall or window frame to reduce
children’s access to the cord loop. Young children can strangle in cord loops. They can also wrap cords around
their necks and strangle.
CAUTION: The shade will not operate properly unless the cord tensioner is secured. A cord tensioner installation kit
has been included with your shade. Follow the instructions in the kit to correctly secure the cord tensioner.
IMPORTANT: Locate the tensioner as close to the window as possible to minimize accessibility by children and pets.
Ensure that the tensioner is not placed in the path of the shade material.
1. Lower the shade and place the hold down pins into the bottom rail end caps.
2. Mark the hold down bracket locations on the mounting surface.
3. With the brackets level, attach them using two screws.
4
Color Coordinated Handle
Optional Clear Insert
Clear Plastic Handle
Indicator Line
Universal
Cord Tensioner
Installing the Shade
Installing the Cord Tensioner
Attaching Hold-Down Brackets (optional)

• Raise and lower the shade several times.
• If the length is incorrect or the bottom rail is not level, use the following steps to correct.
BOTTOMRAIL SHADE ADJUSTMENT
1. Lift bottomrail on the side to be adjusted. This will take the weight off the cord.
2. Use a screwdriver or dime.
• Turn screw clockwise to lift that side of the shade.
• Turn screw counter clockwise to lower that side of the shade.
• Half a revolution is 1/4” adjustment (maximum adjustment is 1/2”).
INTERMEDIATE RAIL SHADE ADJUSTMENT
1. Lift intermediate rail on side to be adjusted. This will take the weight off the cord.
2. Use a screwdriver or dime.
• Turn screw clockwise to lift that side of the rail.
• Turn screw counter clockwise to lower that side of the rail.
• Half a revolution is 1/4” adjustment (maximum adjustment is 1/2”).
CONTINUOUS CORD LOOP SHADES
TO RAISE AND LOWER THE SHADE:
1. Pull down on the cord loop to raise and lower.
2. One side of the loop will raise the shade and one side will lower it.
3. If the same cord is continuously pulled after lowering, the shade will begin to rise.
NOTE: Don’t raise shade any higher than it was intended to go. If shade doesn’t raise evenly, in most cases lowering it completely will allow cords
to re-align on the spool.
CAUTION: The shade will not operate properly unless the cord tensioner is secured. A cord tensioner installation kit has been included with your shade.
CORDLESS LIFT SHADES
TO RAISE AND LOWER THE SHADE:
1. Hold the handle in the center portion of the bottomrail to ensure level movement.
2. Shades over 42” in width will have 2 handles evenly positioned within hands reach along the center portion of the bottomrail to ensure
level movement.
3. Lower the shade by gently pulling downward to the desired position.
4. Raise the shade by gently pushing upward to the desired position
5
Lower Shade Side
Lift Shade Side
Adjusting the Shade
Operating the Shade

THE SHADE WILL NOT SNAP INTO THE INSTALLATION BRACKETS.
• Check that the installation brackets are aligned and level.
THE SHADE IS HARD TO RAISE OR LOWER, OR WILL NOT RAISE OR LOWER.
• Shades cannot be forced into tight inside mount window openings. If an inside mount, check that the shade is installed correctly.
Make sure there is clearance between the ends of the shade and the window casement.
• Check that the installation brackets are level. Shim to level, if necessary.
• If hold-down brackets are used, make sure they have been released.
• Make sure the fabric is not caught.
THE SHADE RAISES OR LOWERS UNEVENLY OR THE BOTTOM RAIL IS UNEVEN.
• Check that the window is square by measuring the diagonals.
• Check that the installation brackets are level. Shim to level, if necessary.
• Adjust the cords under the bottom rail (see “Adjusting The Shade” on page 6).
THE CORD TENSIONER GRABS ONTO THE CORD UPON OPERATION.
• Check that the cord tensioner is mounted properly. Reinstall, if necessary. Refer to the Universal Cord Tensioner Installation Instructions
included with your cord loop shade.
IMPORTANT INFORMATION REGARDING CORDLESS SHADE OPERATION.
• Daily operation of shade will ensure that it performs at its optimal level.
• If the shade is in the lowered position for an extended period of time, extra care needs to be taken when raising the shade. The fabric will
relax and may resist lifting. This is a natural occurrence with all fabric shades. When lifting, you may notice the billowing (falling out) toward
you. This is temporary and can be corrected by slowly raising the shade completely and then operating several times. This allows the fabric
to go back to its pleated state, and the shade will operate as designed.
• If shade has been in the fully raised position for an extended period of time, it may have a tendency to “spring back” above the desired length
of the shade. This is temporary and can be corrected by completely raising the shade and operating several times.
• Operating the shade with the handle(s) provided is recommended so that the shade is balanced when raising and lowering.
• Motorized Shades – see Operating Instructions Guide included with shade/remote control.
Honeycomb shades are made of an anti-static, dust resistant fabric which repels dirt and dust. For most of these fabrics, the following options are
available if your shade needs cleaning.
DUSTING: Regular light dusting with a feather duster is all the cleaning that is needed in most circumstances.
VACUUMING: Use a hand-held vacuum with low suction for more thorough dust removal.
SPOT CLEANING: Use the following steps for spot cleaning: (1) Prepare a solution of warm water and mild dish-washing detergent. (2) Dampen a
clean cloth in the solution and ring it out. (3) Dab the spot with the dampened cloth until it is gone. DO NOT RUB THE FABRIC. (4) Allow the shade
to dry in the completely lowered position.
CAUTION: Avoid creasing Blackout fabrics during cleaning.
DEEP CLEANING: Use the following steps for deep cleaning: (1) Immerse shade in basin or bathtub lled with warm water and mild detergent.
(2) Rinse with clean water. (3) Fully raise shade and tilt to eliminate excess water, (4) Reinstall damp shade, lower it, and let it dry completely.
CAUTION: Do not immerse Blackout fabrics. Do not immerse the headrail or any fabric-wrapped rail.
ULTRASONIC CLEANING: Standard shades, except those made with Blackout Lining can be ultrasonically cleaned by a professional.
• Specify that a mild detergent be used.
• Never immerse the headrail or any fabric-wrapped rail in the solution.
• Dry the shade completely in the lowered position.
CAUTION: Do not ultrasonically clean Blackout fabrics. Do not immerse headrail.
6
TROUBLESHOOTING
CARE AND CLEANING

Lifetime Limited Warranty covering our Custom Made Blinds
We extend this lifetime limited warranty to the original purchaser. This warranty applies only to manually operated Custom Products properly installed
in the window, door or interior area for which they were intended. Installation of the product must be in accordance with accompanying instructions.
The product cannot be modied. It is the purchaser’s responsibility to maintain and clean the product in compliance with the instruction provided.
The product must be used only in the window for which it was purchased. Damage to the product resulting from misuse, abuse, direct exposure to
salty air or discoloration due to sunlight or the passage of time is not covered by this warranty.
This warranty does not apply to conditions caused by normal wear and tear upon the product. This warranty is exclusive and in lieu of all other
obligations, liabilities or warranties. In no event shall the Manufacturer be liable for incidental or consequential damages or for any other direct or
indirect damage, loss, cost, expense or fee. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this
exclusion or limitation may not apply to you.
In the event of a defect under this warranty, we will repair or replace the product, at our option, provided it is returned to our store. Our warranty
obligation excludes shipping charges and labor costs for measuring and installation. Repairs will be made with like or similar parts. This warranty
gives you specic legal rights, and you may have other rights which vary from state to state.
Notes: Motorization Systems are warranted for ve years from the date of purchase. Specialty Blinds and Shades are warranted for one year from
the date of purchase.
This warranty does not apply to Commercial Orders.
1019982 • rev 12/2020
SAFETY LABELS
In compliance with WCMA/ANSI safety standards the warning labels on the bottom rail are designed to be permanent. DO NOT remove the permanent
warning label on the bottom rail. This assures that future owners of this product will be aware of potential dangers associated with this shade.
Young children can STRANGLE in cord loops and in the loop above the cord stop. They can also wrap cords around their necks and STRANGLE.
■Always keep cords out of children’s reach.
■Move cribs, playpens and other furniture away from cords.
Children can climb furniture to get to cords.
■Do not tie cords together.
■Make sure cords do not twist together and create a loop.
Cord Loop and Beaded Chain Loop Shades
■Attach the tensioner to the wall or window casement. See installing the tensioner on page 4.
This can prevent children from pulling cord loops around their necks.
■A tensioner installation kit with instructions for attaching the tensioner is provided. For the shade to operate properly, the tensioner must be
correctly mounted and secured. See tensioner instructions provided for details.
■Only the supplied tensioner(s) and hardware should be used.
7
Window Blind Cord Can STRANGLE
Your Child.
To prevent strangulation, purchase cordless
products or products with inaccessible cords.
5.1.3
La cuerda de la persiana puede ESTRANGULAR a su
niño. Para evitar el estrangulamiento, compre
alternativas cuerda o productos con cuerdas
inaccesibles.
Rev. 5/18 Print 5/18
WARNING/ADVERTENCIA
WARRANTY INFORMATION
CHILD SAFETY

HONEYCOMB Shades
Motorization
Thank you for your purchase. This shade has been custom built for you from the highest quality
materials. To avoid errors and save valuable time, please read these instructions before installing your
new shades.
1. Pencil or Marker
2. Measuring Tape
3. Phillips Screwdriver
4. Carpenter’s Level
5. Power Drill
6. Mounting Fasteners
1
Getting Started ................................................................................................................................................................................................ Page 2
Bracket Installation .......................................................................................................................................................................................... Page 2
Inside Mount .................................................................................................................................................................................................... Page 2
Outside Mount ................................................................................................................................................................................................. Page 3
Shade Installation ............................................................................................................................................................................................ Page 3
Removing the Shade ....................................................................................................................................................................................... Page 3
Operation ......................................................................................................................................................................................................... Page 4
Hold Down Brackets (optional) ........................................................................................................................................................................ Page 4
Adjust Motor Limits on Primary Remote (if desired) ........................................................................................................................................ Page 5
Change Favorite Position (if one was set) ....................................................................................................................................................... Page 5
Adjusting the Shade ........................................................................................................................................................................................ Page 6
Charging the Motor .......................................................................................................................................................................................... Page 6
Replacing the Battery in the Remote ............................................................................................................................................................... Page 6
Solar Charge Unit (optional) ............................................................................................................................................................................ Page 7
Troubleshooting ............................................................................................................................................................................................... Page 8
Care and Cleaning ........................................................................................................................................................................................... Page 8
Child Safety ..................................................................................................................................................................................................... Page 8
Mounting Surface Fastener
Drywall, Plaster Wall Anchors, Expansion Bolts
(Not provided)
Metal Sheet Metal Screws
(Not provided)
Wood No. 6 Hex Head Screws
(Provided)
INSTALLATION INSTRUCTIONS
TOOLS YOU WILL NEED
TABLE OF CONTENTS