SelectBlinds Dual E Series User manual

M Dual 2020.10
Motorized Dual Shade
SELECT DUAL SHADE
CONTENTS PAGE
Getting Started:
• Tools Needed --------------------------- 1
• Considerations Prior to Install ------ 1
• Parts Included in your Package ---- 1
Installation:
• Mounting the Brackets ---------------- 2
• Installing the E-Series Shade ------- 2
• Installing the Motorization Wand --- 3
Child Safety
• Warning ----------------------------------- 4
• Warranty ---------------------------------- 4
Questions?
•Contact your Dealer
Operating the E-Series Shade
• Motorized Shade Introduction ------- 7
• Motorized Wand Instruction Guide - 8
Contacting Us:
Contact your Dealer regarding any question or concerns about your product.
Thank you for Choosing our Dual E-SERIES Shade for your Home or Ofce.
We are condent that you will nd these Dual Shades to be of superior quality and value, compared
to other shades available.
In this guide, you will nd useful information about installation, child safety, cleaning, and warranty
when using our shades.
READ ALL INSTALLATION INSTRUCTIONS BEFORE INSTALLATION
PLEASE KEEP FOR FUTURE REFERENCE / TROUBLESHOOTING
SEL

UP
DOWN
STOP/TILT
PAGE 1
OPTIONAL PARTS: (supplied upon request)
Spacer Blocks
Use for shades that need more space between
the wall.
• A Shade 39” or less come with 2 brackets
• A Shade 78 3/4” or less come with 3 brackets
• A Shade greater than 78 3/4” come with 4 brackets
Your shade will come with two shims to use in case the mounting area is not level.
Place them under the higher side of the mounting area as needed to level out the area.
INCLUDED IN YOUR PACKAGE
Brackets
Quantity: Minimum 2
The wider the shade the more brackets
Screws
Quantity: 4 per bracket
Motorization Wand
Quantity: 1 per shade
Charging Brick / Micro USB
Quantity: 1 (6' cable provided) per shade
Select Motorized Dual Shade
DRILL
LEVEL
PENCIL
SCREWDRIVER
TAPE MEASURE
LADDER
1/16" drill bit,
and 1/4"
hex driver
Flat blade, Phillips, or
1/4" hex driver
THINGS TO CONSIDER BEFORE YOU
BEGIN YOUR INSTALLATION
Your new shade is custom made to your
specications from the nest fabrics available. The
installation should be easy and your shade will look
elegant.
Mounting Options:
Inside mount: Shade
is mounted inside to
the top of the window
frame.
Outside mount:
Shade is mounted
either on or outside the
window frame.
Mounting NOTES:
Mounting screws provided are suitable for
most mounting surfaces. See below for
additional suggestions.
For wallboard or plaster: Use hollow wall
anchors for added support. (not included)
For concrete, stone, brick or tile: Use an
appropriate drill and appropriate anchors
before fastening the screws. (not included)
For metal surfaces: Pre-drill holes and use
appropriate anchors before fastening the
screws. (not included)
Motorized Wand NOTES:
Before the use of the shade, make sure the
wand is attached to the headrail. If it is not,
unpack the wand and hook onto the provided
location.
Plug the Micro USB into the port at the end of
the headrail. (see image 2 on page 3)
We suggest that you charge the shade prior
to installation.
After Installing the shade, charge via the Micro
USB port on the back of the wand for 5-7
hours for a full charge. The Wand is in charge
mode when the Light on the wand is amber.
When fully charged, the light shifts to green.
•
•
•
•
•
•
•
•
SUGGESTED TOOLS (not included)

PAGE 2
1 2
a minimum of 1" - 2" from
edge of window frame
1.5" or more from
front edge
Installing Brackets:
Inside mount: Mount brackets a minimum of 1” - 2”
away from the edges of the product depending on the
overall width of the shade.
the shade should sandwich between top
and bottom of bracket
Headrail cassette
Release tab
Base of Bracket below
Headrail Cassette
INSTALLING THE SHADEMOUNTING BRACKETS
Outside Mount: Outside edge of the brackets should
be positioned at a minimum of 2” from the outside of
the headrail cassette, note the sticker on the headrail
cassette. Use wall anchors for a secure hold. Mark the
position of the bracket as illustrated.
2” from edge of
headrail cassette
Wall
(Above Frame)
ILLUSTRATION ILLUSTRATION
the top of the shade should look like the
referenced image below
Install each bracket with the provided screws per bracket.
Slide headrail cassette into the brackets, be aware that
the release tab should be above the top of the headrail
cassette so it can be accessed to release the shade.
slide the shade into the brackets and it
will “SNAP” into place
You will hear and feel a snap
when it locks into place
Note: The release tab as marked below
if pointed to the left is in the unlock
position. If pointing to the right it is in
the locked position.
locked
unlocked

PAGE 3
3
INSTRUCTION MANUAL
1
2
3
connect control wand into headrail / plug in to the motor
Setting Key
LED Indicator
MICRO USB Plug
Wand
charge and program your shade via the wand
angle shade and it will snap into place
WAND INSTALLATION
Place open end of wand around hook hanging from the
headrail. (see image 1).
Keep in mind that the button side of the Wand is facing
frontward. Plug the Micro USB into the headrail.
(see image 3)
REFER TO FOR
PROGRAMMING DIRECTIONS
Setting Key
Micro USB
Wand Micro USB Wire
Wand Hook
ADJUSTING COUNTER
BALANCE WEIGHTS
4
To prevent uneven raising (Telescoping) of your
Dual Shade you can adjust the counter balance
weights on the bottom side of the bottom rail.
To adjust weight, gently unscrew each screw on
the ends of each weight. Slide the weight left
or right to the desired position, taking care to
equally space the weights from the ends. Test by
raising the shade and look for an even raise. If
shade raises slightly tilted to one side adjust the
appropriate weight to the desired position and
test the shade again. Once shade is balanced
screw weight locks back down.
Select Dual Shade Bottom Rail
Counter Balance Weight

WARNING
EMERGENCY FIRST AID FOR
STRANGULATION
• Remove cord form child's neck
• Call 911 or an emergency Call
Center
• Clear the throat
• Check breathing and heartbeat
• Begin CPR if trained
NOTE:
The Warning labels on the bottom-rails of corded
window coverings contain important safety information.
These warning labels are designed to be permanent, in
accordance with the industry's safety standards, and
must not be removed.
WARRANTY:
We offer a 2 year warranty on the Dual E-Series
motor and controls. Specically, we warrant the Dual
E-Series motor and wand control to be free from
defects in material and workmanship under normal and
proper use for a period of 2 years commencing with
the date stamped on each product. If the product fails
within this 2 year period, we will repair or replace it free
of charge through your end product supplier. Batteries
are not covered by the warranty.
CHOKING HAZARD
• Keep cord out of reach from children.
• Remove objects below window.
• Do not tie cords together.
• Make sure safety cords are located 1-2
inches below the headrail.
• Please reference all warning tags in the
instructions and on the shade.
• Please keep cords out of children and pets
reach, a cord cleat or a cord tensioner
device can be found at a local window
covering store.
WARNING: THE E-SERIES PRODUCT CAN EX-
POSE YOU TO CHEMICALS INCLUDING CARBON
BLACK (CAS NO. 1333-86-4) WHICH IS KNOWN
TO THE STATE OF CALIFORNIA TO CAUSE CANCER. FOR
MORE INFORMATION GO TO WWW.P65WARNINGS.CA.GOV
Window Shade Cord Can
STRANGLE Your Child.
Keep cords out of children’s reach. Short-
en cords to prevent reach. Move crib and
furniture away - Children can climb fur-
niture to reach cords.
La cuerda de la persiana pue-
de ESTRANGULAR a su niño.
Mantenga las cuerdas fuera del alcance de los niños. Acorte las
cuerdas para evitar el alcance. Mueva la cuna y los muebles -
Los niños pueden subir los muebles para alcanzar las cuerdas.
PAGE 4

WE HOPE YOU HAVE FOUND THIS INSTRUCTION GUIDE HELPFUL.
QUESTIONS?QUESTIONS?
Contact your Retail Dealer regarding any questions you may have about your E-SERIES Window Covering.Contact your Retail Dealer regarding any questions you may have about your E-SERIES Window Covering.
WARNING:THEE-SERIES WINDOWCOVERINGCAN EXPOSEYOUTOCHEMICALS INCLUD-
ING CARBON BLACK (CAS NO. 1333-86-4) WHICH IS KNOWN TO THE STATE OF CALIFOR-
NIA TO CAUSE CANCER. FOR MORE INFORMATION GO TO WWW.P65WARNINGS.CA.GOV
TECHNICAL
SPECIFICATIONS
Rated Voltage: 12v
Micro USB
• Charge port on back of wand
Setting Key Button
•
•
•
Motized
Wand
Motized
Wand

Motized
Wand
Motized
Wand
INSTRUCTION MANUAL
TABLE OF CONTENTS
Getting Started
NOTE: Your E-Series Window Covering will come ready to be installed and used without any programming
needed, use the instructions in this guide to assist you.
Operating the Remote
• Motorized Wand Instruction Guide 8Questions?
Contact your Retail Dealer regarding any questions you
may have about your E-SERIES Window Covering.
PLEASE KEEP FOR FUTURE REFERENCE / TROUBLESHOOTING

WELCOME TO YOUR E-SERIES WINDOW COVERING
Setting Key
Button
LED Indicator
MICRO USB Plug
Wand
NOTE: Picture depicts underside
of the headrail
E-SERIES MOTOR NOTE:
The E-SERIES Motor can be found in
the headrail of your E-Series Window
Covering. Ensure that all connections
are connected prior to installation, this
will prevent future need to remove the
Window Covering from the installed
location.
WAKE YOUR E-SERIES WINDOW COVERING
Press, STOP/TILT for 2 seconds to wake your Window Covering.
PAGE 7
Setting Key
Button
Horizontal
Shade
SETTING KEY BUTTON NOTE:
The Setting Key Button can be found on the Motor inside the
headrail of your E-Series Window Covering and at the back of
the Motorized Wand (reference gure 1). A paper clip or rounded pointy
object can be used to troubleshoot the function of the Window
Covering.
If your Motorized Wand is attached, there is a small pinhole
Setting Key Button on the back just above the Micro USB port.
Use this in-place of the Setting Key Button in the headrail, as this
may be difcult to reach.
Figure 1
Setting Key
Button
Back of Motorized
Wand
The Setting Key Button needs to be released at the nal specied jog
to allow for the Window Covering to beep in understanding of the
conguration requested.
Jog: 1 small movement from the motor indicating the device is conguring
Motized Wand
UP
STOP
TILT
DOWN
USB
CHARGING
PORT
SETTING
KEY
BUTTON
NOTE: An orange light
indicates charging, a
green light indicates fully
charged and ready to use.
The Setting Key Button
needs to be released
at the nal specied jog
to allow for the Window
Covering to beep in
understanding of the
conguration requested.
Jog: 1 small movement
from the motor indicating
the device is conguring
| Most setting requests
consist of 2 jogs

PAGE 8
MOTORIZED DUAL SHADE PROGRAMMING INSTRUCTIONS
NOTICE: ALL SHADES COME PRE-PROGRAMMED FROM THE FACTORY. THIS GUIDE SERVES AS A
TROUBLESHOOTING AID. IF THE CONSUMER RESETS THE PROGRAMMING, TECHNICAL SUPPORT WILL BE
AT THE DISCRETION OF THE MANUFACTURER.
Setting Lift Heights
(This section is for setting the lift heights after the shade has undergone a full system reset. For
instructions adjusting an already set lift height see the next section.)
For Top:
• Press and hold the up button for two seconds and the shade will begin to rise. A single push
of the button in this mode will only jog the shade up a few inches. When the shade reaches
your desired top height press the middle stop button. Press and hold the stop and up buttons
at the same time looking for the shad to jog twice and beep once conrming the top height
being set.
For Bottom:
• Press and hold the down button for two seconds and the shade will begin to lower. A single
push of the button in this mode will only jog the shade down a few inches. When the shade
reaches your desired bottom height press the middle stop button. Press and hold the
stop and down buttons at the same time looking for the shad to jog twice and beep once
conrming the bottom height being set.
Adjusting Lift Heights
(This section is to adjust lift heights of an already programmed shade.)
For Up:
• Press and hold the stop and up buttons for 10 seconds looking for a single jog. The shade is
now temporarily in adjustment mode and single pushes of the up or down will raise and lower
the shade in small increments. Press and hold the up button for two seconds and the shade
will begin to raise. Press the stop button at the desired height. Press and hold the stop and up
buttons for two seconds looking for two jogs and one beep. The new top height is set.
For Bottom:
• Press and hold the stop and down buttons for 10 seconds looking for a single jog. The shade
is now temporarily in adjustment mode and single pushes of the up or down will raise and
lower the shade in small increments. Press and hold the down button for two seconds and
the shade will begin to raise. Press the stop button at the desired height. Press and hold the
stop and down buttons for two seconds looking for two jogs and one beep. The new bottom
height is set.
(If heights are not set within one minute of initialization the system will timeout and the motor will
default back to the last used top and bottom heights)
Switching Between Jog and Full Motion Modes
Jog Mode allows for the shade to lower or raise in small increments with a single push of the appropriate
button. A three second push in Jog Mode will raise or lower completely. Full Motion Mode will raise or
lower the shade completely with a single button push.
To change between modes press and hold the up and down buttons on the wand for 3 seconds waiting
for one jog and three beeps conrming the change.

PAGE 9
Changing Lift Directions
Press and hold the wand reset button for 6 seconds waiting for two separate single jogs. Release
immediately after the second jog listening for two beeps. The lifting directions have now been reversed.
Sheer opening is not available in this conguration. Shade can open and close but cannot tilt.
Full System Reset
(This section is for completely resetting the shade. This should only be done as a last resort when all
other solutions have failed.)
To fully reset all settings on the shade press and hold the reset button on either the motor or wand
for 15 seconds looking for three separate sets of jogs followed by three beeps. All settings have now
been reset on the shade. Follow the following steps below with the instructions above to re-initialize
your shades.
Initializing Your Shade:
1. Reverse Shade Direction (Only if reset occurred on the motor. If the reset occurred on the
control wand disregard)
2. Set Top Height
3. Set Bottom Height
4. Switch from Jog Mode to Full Motion Mode if desired
5. Enjoy Your Shade

Notes:

WE HOPE YOU HAVE FOUND THIS INSTRUCTION GUIDE HELPFUL.
QUESTIONS?QUESTIONS?
Contact your Retail Dealer regarding any questions you may have about your E-SERIES Window Covering.Contact your Retail Dealer regarding any questions you may have about your E-SERIES Window Covering.
WARNING:THEE-SERIES WINDOWCOVERINGCAN EXPOSEYOUTOCHEMICALS INCLUD-
ING CARBON BLACK (CAS NO. 1333-86-4) WHICH IS KNOWN TO THE STATE OF CALIFOR-
NIA TO CAUSE CANCER. FOR MORE INFORMATION GO TO WWW.P65WARNINGS.CA.GOV
TECHNICAL
SPECIFICATIONS
Rated Voltage: 12v
Micro USB
• Charge port on back of wand
Setting Key Button
•
•
•
Motized
Wand
Motized
Wand