EN-6
EN
Wall Mount Fan
SFG 4055WH
2014 06/2014
FAN ASSEMBLY
Take the fan out of the packaging material and check that you have all the parts illustrated in the
chapter Description of the fan. Apart from the parts mentioned above, the deliver comes with
a set of two screws and dowels for fastening the holder A9to the wall and a screw with a nut for
fastening the joint on the outer band A1.
Place the motor unit A8on an even dry and stable surface. Place the rear protective grill A6on to
the motor shaft A7. Push the grill A6towards the motor unit A8ensuring the lugs on the front
part of the motor unit A8pass through the round holes in the central part of the rear grill A6.
Use the nut A5to secure the grill A6to the motor unit A8.
On to the motor shaft A7place the fan blades A4and push them in the direction of the motor
unit A8. Make sure that the motor shaft A7with the T-shaped end, slides correctly into the cut-
outs in the centre part of the fan blades A4. Connect the fan blades A4to the shaft A7using the
fastening nut A3. When you spin the fan blades A4by hand, they must rotate freely. If they jam
up, it is necessary to disassemble the fan blades A4and to connect them again to the shaft A7.
On to the rear grill A6place the outer band A1ensuring that the grill A6is seated in the groove
of the band A1around the entire perimeter. Fasten the band joint A1using the supplied screw
and nut. Do not fully tighten the screw so that it is still possible to insert the front protective grill
A2into the outer band A1.
Insert the front protective grill A2into the second groove in the band A1. As soon as the grill
A2snaps into the groove in the band A1around the entire perimeter, tighten the screw used to
secure the joint of band A1. The joint must be firm to prevent the movement of grills A2and A6.
MOUNTING THE FAN ON A WALL
Choose a suitable location for the installation of the fan on the wall. The fan must be located within
reach of a wall power socket and at a sufficient distance from curtains, drapes, sources of heat, etc.
Press the holder A9against the wall so that the hook for hanging the fan points upwards and the
screw holes are aligned on a single vertical axis. Mark out the points for drilling the holes on the
wall and place the holder A9aside. Drill holes into the wall and insert the dowels into them. Press
the holder A9against the wall and screw the screws (2 pcs) into the dowels to fasten the holder
A9to the wall. Hang the fan on the holder A9.
Note:
Before drilling holes into the wall, make sure that in the marked out points there is no electrical
wiring or other utility lines.
OPERATING THE FAN
Connect the fan to a power socket.
1. Setting the speed and turning off the fan
1.1 Set the timer Aqa to the ON position. To set the speed of the fan turn dial Aqs to position
1, 2 or 3 (low, medium and high speed). The fan will run at the set speed.
1.2 To turn off the fan, turn the dials Aqa–qs to the OFF position.
1.3 The control panel Aq; is equipped with a string (SPEED) Aqd, which makes it possible to comfortably
control the dial Aqs. Each time that the string (SPEED) Aqd is pulled, the setting of dial Aqs will
change in the following sequence: OFF 1 2 3 OFF 1 2 3.
2. Setting the auto-off timer
2.1 The timer Aqa can be used to set the automatic shut off time for the fan in the range 0–120
minutes. Use the dial Aqs to select a fan speed. Use the timer Aqa to set the desired shut off time.
The fan will run at the set speed and after the set time elapses it will turn itself off automatically.
The timer Aqa will switch to the OFF position.
