Sencor STM 3760WH Repair manual

05/2021
- 1 -
© 2021
EN Multifunctional Stand Mixer
Translation of the original manual
STM 3760WH / STM 3761BK

05/2021
- 2 -
© 2021
EN Multifunctional Stand Mixer
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
General warnings
■This appliance may be used by persons with physical, sensory or
mental impairments or by persons with insufficient experience
and knowledge, if they are properly supervised or have been
informed about how to use the appliance in asafe manner and
understand the potential dangers.
■This appliance may not be used by children. Keep the appliance
and its power cord away from children.
■Children must not play with the appliance. Cleaning and
maintenance performed by the user must not be performed
by unsupervised children.
■In the event that the power cord is damaged, have it repaired
at aprofessional service centre to prevent causing adangerous
situation. It is forbidden to use the appliance if it has adamaged
power cord.
Warning:
Incorrect use may lead to injuries.
■Be especially careful not to injure yourself on the sharp cutting
edges when handling the chopping blades, especially when
removing the blades from the blending jar or smoothie jar,
when emptying the container and when cleaning it.
■The surfaces of the appliance that come into contact with food
must always be cleaned according to the instructions in this
user'smanual.
■Always turn off the appliance and disconnect it from the power
socket if you will not be using it and if you will be leaving it

05/2021
- 3 -
© 2021
without supervision, before assembly, disassembly, cleaning or
moving it.
■Before replacing the accessories or accessible parts that move
during use, turn the appliance off and disconnect it from the
power supply.
Electrical safety
■ Before connecting this appliance to apower socket, make sure that the voltage stated on its rating label corresponds to the voltage in your power socket.
■ Connect the appliance only to aproperly grounded socket. Do not use an extension cord.
■ Do not connect and disconnect the power cord to and from the power socket with wet hands.
■ Ensure that the power plug contacts do not come into contact with water or moisture.
■ Do not disconnect the appliance from the power socket by pulling on the power cord. This could damage the power cord or the power socket. Disconnect the
cord from the power socket by gently pulling the plug of the power cord.
■ Do not place heavy items on the power cord. Make sure the power cord does not hang over the edge of atable and that it is not touching ahot surface or
sharp objects.
■ To avoid the danger of injury by electrical shock, do not repair the appliance yourself or make any adjustments to it. Have all repairs or adjustments of the
appliance performed at an authorised service centre. Tampering with the appliance during the warranty period may void the warranty.
■ Do not spray the appliance with water or any other liquid. Never wash it under running water or submerge it in water or another liquid.
■ Always turn off the appliance and disconnect it from the power socket when you have finished using it.
■ This appliance is not designed to be controlled using aprogrammed device, external timer switch or remote control.
■ Only run the appliance after submerging the attachments in the bowl with the ingredients. To prevent food from splashing out, keep the attachments
submerged in the container while the appliance is running.
■ If food sticks to the attachments or the inside of the bowl, turn off the appliance and disconnect it from the power socket. Use a spatula to clean the
attachments and the sides of the bowl.
■ Avoid coming into contact with the rotating parts of the appliance. While using it, do not place hands, forks or any other utensils into the bowl with the
ingredients, and keep hair, clothing, etc. at asufficient distance from the rotating parts of the appliance. If afork or another utensil falls into the container
while the appliance is running, immediately it off.
■ Make sure that no hair, clothing or other items enter the feed tube of the meat grinder or grater while it is running. Do not put anything other than the
ingredients that are to be processed into the feed tube.
■ Never use your fingers or other items to push ingredients through the feed tube of the meat grinder or grater. For this purpose there is apusher included as
an accessory.
■ Do not tilt open the multi-function head during operation.
■ Be especially careful when handling hot liquids and foodstuffs. Hot steam or splashing hot foods and liquids may cause scalding. For reasons of increased
safety, it is recommended to allow hot liquids and foods to cool down before processing them.
■ If you have just processed hot foods, the removable attachments may be hot after they are used.
■ Before attaching attachments to the appliance, removing or replacing them, ensure that the appliance is turned off and disconnected from the power socket.
■ To prevent injury caused by sharp edges, be especially careful when handling the grinding blade of the meat grinder and the blade assembly of the blender.
Increased attention must also be paid when emptying out the blending jar, when removing the blade assembly from the blending jar, when removing the
grinding blade from the chamber, and when cleaning the appliance.
■ Do not attempt to grind bones, nut shells or other hard ingredients.
■ Hot liquids up to atemperature of 80 °C may be processed in the stainless steel bowl. Be especially careful when handling hot liquids. Hot steam or splashing
hot foods and liquids may cause scalding. Never start the blender without the lid properly seated in position. When processing hot liquids, do not remove the
inner cap during operation. Do not touch the hot surface. Use the handle to carry the blending jar when it is hot.
■ The maximum continuous operating time is 10 minutes. Do not exceed the maximum operating time of 5 minutes when in the kneading mode and do not
exceed the maximum operating time of 2 minutes when using the blender. Before starting it again, allow the appliance to cool down for 30 minutes.
Safety during maintenance
■ Allow the appliance to always fully cool down before cleaning it.
■ Regularly clean the appliance after each use according to the instructions in chapter Maintenance and cleaning. Do not perform any maintenance on the
appliance apart from the maintenance procedure described in chapter Maintenance and cleaning.
■ Do not wash the multi-function head or stand under running water or submerge it in water or another liquid. The stand mixer is not designed to be washed
in adishwasher.
■ The removable attachments are intended for short term contact with food (including beverages), i.e. max. 4 hours. To prevent damaging their surface, do not
leave them submerged, for example in water for extended periods of time.
■ Before storing the appliance, check that the multi-function head is tilted to the horizontal position.

05/2021
- 4 -
© 2021
STM 3760WH / STM 3761BK
9
2
3
4
5
7
6
8
10
11
1
12
13
14
A

05/2021
- 5 -
© 2021
2
3
4
1
B
4
2
3
1
5
C

05/2021
- 6 -
© 2021
4
5
1
2
3
7
6
8
9
10
11
12
D

05/2021
- 7 -
© 2021
2
34
1
E
F

- 8 - 05/2021
© 2021
EN
Multifunctional
Stand Mixer
User'smanual
BEFORE FIRST USE
■ Prior to using this appliance, please read the user'smanual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user'smanual in asafe place where it can be easily retrieved for future use.
In the event that you hand this appliance over to somebody else, make sure to also
include this user'smanual.
■ We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
■ Carefully unpack the appliance and take care not to throw away any part of the
packaging before you find all the parts of the appliance.
DESCRIPTION OF THE APPLIANCE AND ACCESSORIES
A1 Tilt-out multi-function head
A2 Removable cover of the front meat
grinder or grater attachment hub
A3 Button for releasing the meat
grinder from the attachment hub
A4 Front attachment hub for meat
grinder and grater
A5 Fastening shaft for attachments
A6 Base for stainless steel bowl
A7 Anti-slip feet
A8 Tilt-open cover of the top blender
attachment hub
A9 Light
A10 Multi-function head tilt-out and
tilt-down button
A11 Control knob with light
- 0 (turned off, stand-by mode)
- speed levels 1-2-3-4-5-6,
- blender mode in blending jar ( )
- blender mode in smoothie jar ( )
- light ( )
A12 Transparent anti-splash cover with
feed hole
A13 Stainless steel bowl lid
A14 4.5-litre stainless steel bowl for
processing food
B1 Balloon whisk
B2 Beater
B3 Kneading hook
B4 Elastic beater
C1 Inner cap
C2 Outer lid with ahole for adding
ingredients
C3 1.5-litre blending jar
C4 Blade assembly
C5 Base for mounting/removing the
blender from the attachment hub
D1 Grinder
D2 Screw shaft
D3 Grinding blade
D4 Fine grinding plate
D5 Screw ring
D6 Medium grinding plate
D7 Coarse grinding plate
D8 Pusher
D9 Hopper
D10 Grinding chamber
D11 Pasta making attachments
D12 Sausage stuffer attachment
D13 Cookie maker with holder
INTENDED USE OF THE APPLIANCE
■ The stand mixer is intended and designed for processing astandard amount of food
in the household. It is suitable for blending, beating, kneading, grinding and grating.
BEFORE FIRST USE
■ Before first use, thoroughly wash all parts that come into contact with food in hot
water using neutral dishwashing detergent. Then rinse everything with clean water
and allow to dry naturally or wipe dry thoroughly using awiping cloth.
Attention:
Accessories B1 to B4 and the meat grinder D1 are not intended for
washing in adishwasher. Other removable parts may be washed
in adishwasher.
When washing the blade assembly A21, take special care to avoid
injury on the sharp cutting edges.
■ Use alightly dampened wiping cloth to wipe the outside parts of the stand mixer.
Attention:
Do not rinse the stand mixer or its power cord under water or
submerge it in water. Neither the stand nor the multi-function
head are intended for washing in adishwasher.
BEATING, WHIPPING AND KNEADING
PLANETARY MIXING SYSTEM
■ The planetary mixing system is based on the principle of dual rotation of the
attachment. The attachment rotates anticlockwise along the inner perimeter of the
bowl while rotating around its own axis in the opposite direction. This ensures that
ingredients inside the bowl are processed thoroughly and evenly.
PREPARING FOR OPERATION
Warning:
Before you start assembling or disassembling the accessories
of the stand mixer, check that it is turned off and disconnected
from the power socket. Attaching an attachment while the multi-
function head is connected to mains power, may result in it being
accidentally turned on and serious subsequent injuries.
Selecting an attachment type
Attachment type Operation
Balloon whisk B1
It is used for whisking whole eggs or egg whites, whipped
cream, foamy creams, etc. Do not use it for beating or
kneading doughs.
Beater B2
It is used for beating light and medium heavy yeast-free
doughs, for preparing sauces, creams, fillings, etc. Do not
use it for kneading heavy doughs.
Kneading hook B3
It is used for kneading various types of doughs including
heavy and thick doughs such as for example bread dough,
pizza dough, fresh pastry doughs, etc.
Elastic beater B4
It is used for beating dessert creams, instant puddings,
mayonnaise, sponge cake dough, etc. Do not use it for
kneading heavy doughs.
Adding ingredients into the bowl
■ Put the ingredients that you wish to process into the stainless steel bowl. In asingle
batch, it is possible to process no more than 0.8 kg of heavy dough or 2.2 kg of
light dough.
■ The maximum number of egg whites that can be whisked at once is 8.
■ We recommend filling the bowl no higher than the 4-litre level mark.
■ If an insufficient amount of ingredients are put in the bowl (less than 0.3 litres of
dough), then they may not be optimally processed.
Mounting attachments
■ Place the stand mixer on an even, dry and stable surface, for example on akitchen
countertop.
■ Press button A10. This will release the multi-function head. Tilt the multi-function
head upwards all the way, so that aclick is heard.
■ If you wish to use the transparent anti-splash cover A12then you must attach it
before mounting an attachment. Put the lid on the bottom side of the head with the
shaft and turn it anticlockwise to secure it in place.
■ Select an attachment and slide it on to the mounting shaft A5. Turn the attachment
anticlockwise to secure it in position. Lightly pull the attachment downwards with
one hand to check that it is properly attached.
Mounting the stainless steel bowl
■ Insert the stainless steel bowl into the base unit A6 and secure it in place by turning
it clockwise When the bowl is properly attached, it cannot be separately lifted out
of the base.
■ Use one hand to push down the button A10 and the other to push down the head
so that it clicks into place.
OPERATION
■ Connect the power cord to an el. power socket.
■ Use the control knob to set the required speed level from 1 to 6. We recommend to
start at alower speed and to increase it gradually. You can change the speed setting
even while the appliance is running. We recommend that runny doughs and sauces
are processed at lower speed levels; this will prevent ingredients from splashing out.
As soon as they are mixed together, increase the speed to the required level.
Attention:
Items such as spoons, kitchen knives, forks, etc. must not be
placed into the appliance during operation as this could result in
injury or damage to the appliance.
Releasing stuck-on ingredients
■ In the event that an ingredient (e.g. dough) sticks to the edge of the bowl, turn off
the stand mixer and disconnect it from the power socket.
■ Tilt open the head. For better visibility into the bowl, it is possible to turn on the light
by setting the control knob to position .
■ Using an ordinary scraper, remove the stuck-on ingredient on the edge of the bowl
and put it into the middle of the bowl.
■ Tilt the head back into the operating position and reconnect it to mains power.
Continue processing.
Operating time of the stand mixer
■ When beating, whisking or kneading, do not leave the appliance in continuous
operation for longer than 10 minutes.
■ When kneading thick, heavy dough, do not allow the appliance to run for longer
than 6 minutes.
■ After one of the mentioned times has elapsed, turn off the appliance and allow it to
cool down. The appliance can be used again after 30 minutes.

- 9 - 05/2021
© 2021
Quick guide to processing ingredients
Attachment type Ingredients Speed Processing
time
Balloon whisk B1
Light mixtures (for example
cream, egg whites, pudding,
carrot)
5-6 4 min
Beater B2 and
elastic beater B4
Moderately heavy mixtures
(for example cake dough,
pancake mixes or sponge cake
dough)
3–4 6 min
Kneading hook
B3
Heavy mixtures (for example
bread and pastry dough) 1–3 4–5 min
Note:
The above processing times are only areference. To prevent ingredients
from splattering out of the bowl, select an initial speed level of 1 or 2.
Then set ahigher
speed as required. For easier mixing of dough we recommended soft
margarine or butter.
When whipping egg whites, the bowl and the beater must be perfectly
clean and dry. Even asmall amount of fat may result in that the egg whites
will not be whipped to the desired snowy consistency.
Whipping cream should be cooled to atemperature of 6 °C prior to being
whipped.
Prior to processing them, allow the ingredients used for making various
doughs to rest at room temperature.
ENDING OPERATION AND DISASSEMBLING THE ACCESSORIES
■ After you have finished using the appliance, set the control knob to the 0 position
(off) and disconnect the power cord from the power socket.
■ Push down button A10 and tilt the head upwards all the way, so that aclick is heard.
■ Turn the attachment clockwise to release it, and then remove it.
■ Turn the stainless steel bowl anticlockwise and remove it from the base unit.
■ Remove the transparent anti-splash cover A12 by turning it clockwise.
■ Tilt the head back down to the horizontal position.
■ Clean out the stand mixer and the used accessories after each use according to the
instructions in chapter CLEANING AND MAINTENANCE.
BLENDING
USING THE BLENDER
■ The blender is intended for preparing meals and drinks such as milkshakes, creamy
soups, sauces, spreads, fresh baby foods, nutritional drinks, etc. It is not intended for
juicing fruit and vegetables, preparing potato purée, yeast dough or for whipping
egg whites.
ASSEMBLING THE BLENDER
Preparing the stand mixer for blending
■ In order to be able to assemble and subsequently use the blender, it necessary to
meet the following conditions:
- place the stand mixer on an even, dry and stable surface, for example on a-
countertop.
- the stand mixer must be disconnected from the power socket
- the multi-function head must be tilted down into the horizontal position and no
other attachment may be mounted on it
- the stainless steel bowl must be mounted on the base unit
■ Tilt open the cover A8. Underneath this cover there is a hub for mounting the
blending or smoothie jar.
Assembling and mounting the blending jars (fig. E)
■ Prior to putting on the blending jar on to the hub, first check that the base with the
blade unit is correctly mounted in the jar.
■ Place the blending jar on to the top hub and turn it clockwise to secure it in place.
The safety mechanism will prevent the blender from starting unless the jar is
correctly mounted on the hub.
■ Place ingredients into the jar. We recommend cutting larger ingredients into smaller
pieces before blending them.
Note:
Never fill the jar past the maximum mark.
When processing hot liquids or liquids that expand in volume during the
blending process, it is recommended to fill the blending jar to no more
than 2/3 of its maximum capacity.
■ Seat the outer lid C2 on to the blending jar and push it down so that it firmly adheres
to the edges of the jar. Place the inner cap C1 into the opening in the lid and secure
it in place by turning it clockwise.
QUICK GUIDE TO PROCESSING INGREDIENTS
Ingredients Speed selection Recommended
blending time
Fruit, vegetables cut
into smaller pieces
or 5-6
30 s
Baby food
or 5-6
40 s
Spreads, dressings, marinades
or 5-6
30 s
Soups
or 5-6
40 s
Ice cubes
As necessary
Note:
The above food processing times are only areference. The actual mixing
time depends on the size of the ingredients, their amount and the
required final consistency.
ADVICE AND TIPS FOR BLENDING
■ First cut food with afirm consistency such as fruit and vegetables into smaller pieces
measuring 3 cm and only then blend it.
■ First, blend a smaller amount of ingredients and then gradually add more
ingredients through the hole in the lid C1 while blending. In this way, you will
achieve better results than by adding all ingredients into the blending jar at once.
■ If you need to blend food of a solid consistency together with liquids, we
recommend that you first blend the food of solid consistency and a part of the
liquids. Then gradually add the remaining liquids through the hole in the lid while
blending.
■ When blending very think liquids, start the blender repeatedly in short interval
bursts.
■ Ice cubes must be processed immediately upon being removed from the freezer.
When the ice starts to melt, the ice cubes will stick together and it will not be
possible to blend them.
BLENDING
■ Check that control knob is set to position 0 (off ). Connect the power cord to apower
socket.
■ Use the control knob to set the desired speed level or mode. We recommend to
first set aslower speed to allow the ingredients to mix together. Then the speed
may be increased.
Attention:
Do not process hot liquids that are hotter than 80 °C in the
blending jar.
The maximum operating time of the blender is 2 minutes. Do not
leave the stand mixer in continuous operation for longer than
indicated above. After blending, allow the stand mixer to cool
down for approx. 30 minutes.
The shaft of the head A5 will move when the smoothie jar is used.
■ If you wish to add more ingredients to the blending jar during the blending process,
remove the inner cap C1 and add the ingredients through the hole in the outer
lid C2. However, never remove the outer lid while blending. When processing hot
liquids, the inner cap C1 must remain closed.
■ In the event that food is sticking to the blade assembly or the walls of the blending
jar, turn off the stand mixer by turning the control knob to the 0 position (off)
and disconnect it from the power socket. Make sure that the blade assembly has
stopped rotating. Carefully remove the jar from the multi-function head by turning
it anticlockwise and pulling it upwards. Remove the lid and, using aspatula, clean
the blade assembly and the walls of the blending jar. Put the lid back on and
reattach the jar to the multi-function head. Plug the power cord into apower socket
and continue blending.

- 10 - 05/2021
© 2021
ENDING BLENDING AND DISASSEMBLING THE JAR
■ After you have finished blending, set the control knob to the 0 position (off) and
disconnect the power cord from the power socket. Before performing any other
activity, check that the blade assembly inside the jar has stopped rotating.
Disassembly of the blending jar
■ Release the blending jar by turning it anticlockwise and take it off by lifting it
vertically upwards off the top hub.
■ If you wish to prepare the blending jar for cleaning, pour the blended contents out
into asuitable bottle or bowl, and wash out the blending jar using water and wipe
it dry.
■ Turn the blending jar upside down
■ Use one hand to grasp the handle of the blending jar and with the other hand
release the base with the blade assembly by turning it clockwise.
■ In the event that it is not possible to release the base by hand, mount the blending
jar back on to the hub of the stand mixer. Use one hand to hold the base with the
blade assembly and the second hand to turn the blending jar anticlockwise. The
blending jar should release and it should be possible to screw it off the base. After
screwing off the blending jar, release the base from the hub. Put the hub cover back
in its place.
■ Clean the individual parts of the blending jar according to the instructions in
chapter CLEANING AND MAINTENANCE.
GRINDING MEAT
USING THE GRINDER
■ The grinder is intended for grinding all types of meat that is free of bones, tendons
and skin, and it can also grind fruit and vegetables. It also serves to make pasta,
cookies and to stuff sausages.
■ The grinder is not intended for crushing bones, nuts or other hard ingredients or
frozen food.
ASSEMBLING THE GRINDER
Preparing the stand mixer for grinding
■ In order to be able to assemble and subsequently use the grinder, it necessary to
meet the following conditions:
- place the stand mixer on an even, dry and stable surface, for example on a-
countertop.
- the stand mixer must be disconnected from the power socket
- the multi-function head must be tilted down into the horizontal position and no
other attachment may be mounted on it
■ Remove the cover A2. The front attachment hub for mounting the grinder is found
underneath this cover.
Assembling and mounting the grinder (fig. F)
■ Insert the screw shaft D2 into the grinding chamber D10 with the cogged wheel
entering first.
■ Place the grinding blade D3 on to the shaft (with the cutting edge facing outwards
from the chamber) and on to it attach agrinding plate. Make sure that the notch in
the grinding chamber slides into the groove in the grinding plate.
Attention:
When mounting the grinding blade, be very careful not to injure
yourself on the sharp edge.
■ Place the screw ring D5 on to the grinding chamber and tighten it securely by
screwing it clockwise.
■ Tilt the assembled grinder to the right at an angle of 45°, push it against the front
attachment hub A4 and turn it anticlockwise to set it into the operating position.
The operating position is indicated by button A3 popping out and an audible click.
Note:
The stand mixer is equipped with a safety mechanism that prevents it
from being started unless the grinder is properly mounted and secured
on the front attachment hub.
■ Seat the hopper D9 on to the top feed tube of the grinder and place asuitable
container underneath the grinder for capturing the processed food.
GRINDING
■ First prepare the meat for grinding in the following way: Remove all bones, tendons,
cartilage and cut the meat into 2 × 2 × 6 cm size pieces that will freely pass through
the top feed tube of the grinder.
Attention:
Do not process frozen meat. Allow it to defrost before grinding it.
■ Check that control knob is set to position 0 (off ). Connect the power cord to apower
socket.
■ Use the control knob to set the desired speed. We recommend to initially set speed
3 and then increase it as required. Gradually place the meat pieces into the feed
tube and push them in using the pusher D8. Take care not to clog up the feed tube
by alarge amount of meat. Do not process more than 5 kg of meat per batch. The
processing time is only several minutes.
Warning:
Do not use fingers or other items to push the meat in. Always use
the pusher D8 designed for this purpose.
The maximum operating time of the grinder is 6 minutes. Do not
leave the stand mixer in continuous operation for longer than
indicated above. After grinding, allow the stand mixer to cool
down for approx. 30 minutes.
The shaft of the head A5 will move during the grinding process.
■ The ground meat will fall into the prepared bowl. The meat that remains in the
grinding chamber can be removed by grinding aslice of bread or abread roll.
MAKING COOKIES, PASTA OR STUFFING SAUSAGES
■ Proceed in the same manner as when assembling the grinder for grinding meat,
only with the difference that, instead of the grinding blade, insert the one of the
sausage stuffer attachments D11 or the pasta maker attachment D12.
ENDING OPERATION AND DISASSEMBLING THE GRINDER
■ After you have finished grinding, set the control knob to the 0 position (off) and
disconnect the power cord from the power socket.
■ Remove the hopper D9. Then press the button A2 and remove the meat grinder by
turning it clockwise and sliding it out of the hub. After removing the grinder, put the
cover A2 back in its place.
■ When disassembling the meat grinder into its individual parts, proceed in the
reverse sequence.
■ Clean out the grinder and the used accessories after each use according to the
instructions in chapter CLEANING AND MAINTENANCE.
CLEANING AND MAINTENANCE
Attention:
Prior to cleaning or maintenance, always disconnect the appliance
from the power supply and allow it to cool down completely.
The stand mixer and its tilt-out head and its power cord are not
intended for washing in adishwasher.
Do not spray these parts with water or any other liquid or
submerge them in water or any another liquid.
■ After using it, thoroughly wash all parts that came into contact with food in hot
water using neutral dishwashing detergent. Then rinse everything with clean
water and allow to dry naturally or wipe dry thoroughly using awiping cloth. After
washing and drying, we recommend to coat the grinding blade D3 and the grinding
plate D4 with cooking oil.
■ If you whisked egg whites, first rinse the stainless steel bowl and the used whisk
under cold water. If you were to use hot water, the egg white remains would harden
and their removal would be more difficult.
Attention:
The whisk and the beater attachments, the body of the meat
grinder and the body of the grater are not intended for washing
in a dishwasher. Other removable parts may be washed in
adishwasher.
When washing the grinding blade and the blade assembly of the
blending or smoothie jar take special care to avoid injury on the
sharp cutting edges.
■ Clean the blending jar C3 or the smoothie jar C6 by filling it with clean water and
a few drops of kitchen detergent and then mounting it on the hub of the stand
mixer and running it for 10 to 15 seconds. Then turn off the stand mixer, disconnect
it from the power socket, and after the rotating parts have come to astop, remove
the jar. Empty out the contents of the jar and then thoroughly rinse it out with clean
water and wipe it dry.
■ Wipe the outer parts of the stand mixer and the multi-function head using alightly
dampened wiping cloth or sponge.
Attention:
Never use chemicals, dishwashing wool, steel wool or cleaning
agents with an abrasive component since these may seriously
damage the surface of the stand mixer or the multi-function head.
STORAGE
■ Before storing it, the appliance and its accessories must be completely cool, turned
off and disconnected from the power supply, clean and dry.
■ Place the stainless steel bowl into the base on the stand and into it you can place
the beater, whisk and kneading hood. Tilt the multi-function head to the horizontal
position. Store the stand mixer and all the accessories in aclean, dry place out of
children'sreach.
Attention:
Keep the stored stand mixer away from extreme temperatures,
direct sunlight and excessive humidity and do not store it in an
overly dusty environment. Do not place anything on to the stored
stand mixer.