Sentera Controls MTP-D010 Series Service manual

Mounting and operating instructions
MTP-D010 ACTIVE
POTENTIOMETER

www.sentera.eu
MIW-MTP-D010-AT-BT-EN-000-06/02/2019 2 - 7
Table of contents
SAFETY AND PRECAUTIONS 3
PRODUCT DESCRIPTION 4
ARTICLE CODES 4
INTENDED AREA OF USE 4
TECHNICAL DATA 4
STANDARDS 4
OPERATIONAL DIAGRAMS 5
WIRING AND CONNECTIONS 5
MOUNTING INSTRUCTIONS IN STEPS 5
VERIFICATION OF INSTALLATION INSTRUCTIONS 7
TRANSPORT AND STORAGE 7
WARRANTY AND RESTRICTIONS 7
MAINTENANCE 7
MTP-D010 ACTIVE
POTENTIOMETER

www.sentera.eu
MIW-MTP-D010-AT-BT-EN-000-06/02/2019 3 - 7
back to the table of contents
SAFETY AND PRECAUTIONS
Read all the information, the datasheet, mounting and operating instructions and
study the wiring and connection diagram before working with the product. For
personal and equipment safety, and for optimum product performance, make sure you
entirely understand the contents before installing, using, or maintaining this product.
For safety and licensing (CE) reasons, unauthorised conversion and/ or modifications
of the product are inadmissible.
e product should not be exposed to abnormal conditions, such as: extreme
temperatures, direct sunlight or vibrations. Long-term exposure to chemical
vapours in high concentration can affect the product performance. Make sure the
work environment is as dry as possible; avoid condensation.
All installations shall comply with local health and safety regulations and local
electrical standards and approved codes. is product can only be installed by
an engineer or a technician who has expert knowledge of the product and safety
precautions.
Avoid contacts with energised electrical parts. Always disconnect the power
supply before connecting, servicing or repairing the product.
Always verify that you apply appropriate power supply to the product and use
appropriate wire size and characteristics. Make sure that all the screws and nuts
are well tightened and fuses (if any) are fitted well.
Recycling of equipment and packaging should be taken into consideration and these
should be disposed of in accordance with local and national legislation/regulations.
In case there are any questions that are not answered, please contact your
technical support or consult a professional.
MTP-D010 ACTIVE
POTENTIOMETER

www.sentera.eu
MIW-MTP-D010-AT-BT-EN-000-06/02/2019 4 - 7
back to the table of contents
PRODUCT DESCRIPTION
MTP-D010 potentiometer series are intended for direct control of EC fans / motors
and actuators. ey require a supply voltage of 3—15 VDC and provide a stepless
output signal that can be set by a rotary knob within a range adjustable via two
trimmers for Vmin (10—70 % Vin) and Vmax (30—100% Vin). ey are suitable for
applications where a DC control signal is required. e -AT version features an off
position, while -BT provides control within the range Vmin—Vmax. eir enclosures
are splash-proof and suitable for both inset and surface mounting.
ARTICLE CODES
Code Output Off position
MTP-D010-AT 0, Vmin—Vmax yes
MTP-D010-BT Vmin—Vmax no
INTENDED AREA OF USE
■Applications where a DC control signal is required
■For indoor use only
TECHNICAL DATA
■Power supply: 3—15 VDC
■Output:
►MTP-D010-AT: 0, Vmin—Vmax
►MTP-D010-BT: Vmin—Vmax
■Load: RL≥ 2 kΩ
■Vmin: 10—70 % Vin
■Vmax: 30—100% Vin
■Enclosure:
►External: ASA, white-ivory (RAL 9010), IP54 (according to EN 60529)
►Internal: polyamide, white-ivory (RAL 9010), IP44 (according to IEC 60335)
■Operating ambient conditions:
►temperature: 0—40 °C
►rel. humidity: < 100 % rH (non-condensing)
►Storage temperature: -10—55 °C
STANDARDS
■Low Voltage Directive 2014/35/EC
■EMC Directive 2014/30/EC
■WEEE Direc tive 2012/19/EU
■RoHs Directive 2011/65/EU
MTP-D010 ACTIVE
POTENTIOMETER

www.sentera.eu
MIW-MTP-D010-AT-BT-EN-000-06/02/2019 5 - 7
back to the table of contents
OPERATIONAL DIAGRAMS
MTP-D010-AT MTP-D010-BT
Output, VDC
Max
100 % Vin
Vmax
Vmin
Min.
10 % Vin
30 % Vin
70 % Vin
O
On Potenometer posion
Output, VDC
Max
100 % Vin
Vmax
Vmin
Min
10 % Vin
30 % Vin
70 % Vin
Potenometer posion
WIRING AND CONNECTIONS
Vin (+) Supply voltage (3—15 VDC)
Vin(-) Supply voltage, ground
Vout (-) Output, ground
Vout (+) Output voltage
Connections Cable cross section: max. 2,5 mm²
MOUNTING INSTRUCTIONS IN STEPS
Before you start mounting your potentiometer, read carefully “Safety and Precautions”
and follow the steps:
For inset mounting
1. Remove the knob by turning it to the right until it pops out.
2. Unscrew the loose nut to remove the cover of the external enclosure.
3. Do the wiring according to the wiring diagram (see Fig. 1 Wiring and connections).
4. Mount the internal enclosure into the wall according to the mounting dimensions
shown in Fig. 2 Mounting dimensions - inset mounting.
Fig. 1 Wiring and connections
Vmax adjustment
trimmer
Supply voltage
( 3 —15 VD C )
Output:
-AT: 0, Vmin—Vmax
-BT: Vmin—Vmax
Vmin adjustment
trimmer
MTP-D010 ACTIVE
POTENTIOMETER

www.sentera.eu
MIW-MTP-D010-AT-BT-EN-000-06/02/2019 6 - 7
back to the table of contents
Fig. 2 Mounting dimensions - inset mounting
26 33
50x50
82
89
62
50
62
60
NOTE Mount the unit so that the terminal block and connections are at the lower side.
5. Adjust the Vmin and Vmax trimmers.
6. Mount back the cover and secure it with the nut.
7. Put back the knob and turn it to off position (-AT version) or minimum position
(-BT version).
8. Turn on the power supply.
For surface mounting
1. Remove the knob by turning it to the right until it pops out.
2. Unscrew the nut to remove the cover of the external enclosure.
3. Mount the external enclosure onto the surface by means of screws and dowels
(notincluded in the set) adhering to the mounting dimensions shown in Fig. 3
Mounting dimensions - surface mounting.
Fig. 3 Mounting dimensions - surface mounting
82
89
69
82
62
62
4. Insert the cables through the grommets.
5. Do the wiring according to the wiring diagram (see Fig. 1 Wiring and connections).
6. Insert the internal enclosure into the external one and fix it using the screws and
washers included in the set.
NOTE Mount the unit so that the terminal block and connections are at the lower side.
7. Mount back the cover and secure it with the nut.
8. Put back the knob and turn it to off position (-AT version) or minimum position
(-BT version).
9. Turn on the power supply.
MTP-D010 ACTIVE
POTENTIOMETER

www.sentera.eu
MIW-MTP-D010-AT-BT-EN-000-06/02/2019 7 - 7
back to the table of contents
NOTE A 5 mm hole can be drilled at the bottom of the external enclosure to drain the
condensed water.
VERIFICATION OF INSTALLATION INSTRUCTIONS
ATTENTION Use only tools and equipment with non-conducting handles when working on
electrical devices.
■In case of faulty operation, please check if:
►the right voltage is applied;
►all connections are correct;
►the regulated device is functioning.
TRANSPORT AND STORAGE
Avoid shocks and extreme conditions; stock in original packing.
WARRANTY AND RESTRICTIONS
Two years from the delivery date against defects in manufacturing. Any modifications
or alterations to the product after the date of publication relieve the manufacturer
of any responsibilities. e manufacturer bears no responsibility for any misprints or
mistakes in this data.
MAINTENANCE
In normal conditions this product is maintenance-free. If soiled, clean with a dry or
damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these
circumstances the unit should be disconnected from the supply. Pay attention that no
fluids enter the unit. Only reconnect it to the supply when it is completelydry.
MTP-D010 ACTIVE
POTENTIOMETER