Sentera Controls DSTHM-2 Service manual

Mounting and operating instructions
DSTHM-2 COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 2 - 10
Table of contents
SAFETY AND PRECAUTIONS 3
PRODUCT DESCRIPTION 4
ARTICLE CODES 4
INTENDED AREA OF USE 4
TECHNICAL DATA 4
STANDARDS 4
OPERATIONAL DIAGRAMS 5
WIRING AND CONNECTIONS 5
MOUNTING & OPERATING INSTRUCTIONS IN STEPS 5
OPERATING INSTRUCTIONS 8
VERIFICATION OF INSTALLATION 9
TRANSPORT AND STOCK KEEPING INFORMATION 9
WARRANTY AND RESTRICTIONS 9
MAINTENANCE 9
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 3 - 10
back to the table of contents
SAFETY AND PRECAUTIONS
Read all the information, the datasheet, Modbus map, mounting and operating
instructions and study the wiring and connection diagram before working with the
product. For personal and equipment safety, and for optimum product performance,
make sure you entirely understand the contents before installing, using, or maintaining
this product.
For safety and licensing (CE) reasons, unauthorised conversion and/ or modifications
of the product are inadmissible.
e product should not be exposed to abnormal conditions, such as: extreme
temperatures, direct sunlight or vibrations. Long-term exposure to chemical
vapours in high concentration can affect the product performance. Make sure the
work environment is as dry as possible; avoid condensation.
All installations shall comply with local health and safety regulations and local
electrical standards and approved codes. is product can only be installed by an
engineer or a technician who has expert knowledge of the product and safety
precautions.
Avoid contacts with energised electrical parts. Always disconnect the power
supply before connecting, servicing or repairing the product.
Always verify that you apply appropriate power supply to the product and use
appropriate wire size and characteristics. Make sure that all the screws and nuts
are well tightened and fuses (if any) are fitted well.
Recycling of equipment and packaging should be taken into consideration and these
should be disposed of in accordance with local and national legislation/regulations.
In case there are any questions that are not answered, please contact your
technical support or consult a professional.
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 4 - 10
back to the table of contents
PRODUCT DESCRIPTION
e DSTHM-2 series are combined duct transmitters which measure temperature
and relative humidity. Based on the temperature and relative humidity measurements,
the dew point is calculated. ey are Power over Modbus supplied and all parameters
are accessible via Modbus RTU.
ARTICLE CODES
Code Supply Connection
DSTHM-2 Power over Modbus, 24 VDC RJ45
INTENDED AREA OF USE
Monitoring duct temperature and relative humidity in HVAC applications
TECHNICAL DATA
■Selectable temperature range: -30—70 °C
■Selectable relative humidity range: 0—100 %
■Accuracy: ±0,4 °C (range -30—70 °C); ±3 % rH (range 0—100 % rH)
■Maximum power consumption: 0,36 W
■Nominal power consumption in normal operation: 0,27 W
■Imax: 15 mA
■Minimum airflow velocity required: 1 m/s
■Enclosure and probe material:
►ASA, grey (RAL9002)
■Protection standard: enclosure: IP54, probe: IP20
■Typical field of use:
►temperature: -30—70 °C
►rel. humidity: 0—100 % rH, (non-condensing)
■Storage temperature: -10—60 °C
STANDARDS
■EMC Directive 2014/30/EC:
►EN 61326-1:2013 Electrical equipment for measurement, control and laboratory
use - EMC requirements - Part 1: General requirements
►EN 61326-2-3:2013 Electrical equipment for measurement, control and
laboratory use - EMC requirements - Part 2-3: Particular requirements - Test
configuration, operational conditions and performance criteria for transducers
with integrated or remote signal conditioning
■WEEE Direc tive 2012/19/EC
■RoHs Directive 2011/65/EC
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 5 - 10
back to the table of contents
OPERATIONAL DIAGRAMS
Input register 1 [%]
100
-30 Min range Max range 70 T [°C]
Input register 10 [%]
100
0Min range Max range100 rH [%]
WIRING AND CONNECTIONS
RJ45 socket (Power over Modbus)
Pin 1 24 VDC Supply voltage
Pin 2
Pin 3 AModbus RTU communication, signal A
Pin 4
Pin 5 /B Modbus RTU communication, signal /B
Pin 6
Pin 7 GND Ground, supply voltage
Pin 8
/B
A
GND
24 VDC
8 mm
8 mm
8 mm
8 mm
RJ45
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
3
4
5
6
3
4
MOUNTING & OPERATING INSTRUCTIONS IN STEPS
Before you start mounting the unit, read carefully “Safety and Precautions”.
Follow these steps:
1. When preparing to mount the unit, bear in mind that the probe opening must
be positioned in the centre of the duct. Always use the flange to install the
sensor on round ducts. It is possible to install the sensor without the flange on
rectangular ducts (if necessary), see Fig. 1 and Fig. 2 below.
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 6 - 10
back to the table of contents
Fig. 1 Mounting dimensions
With flange Without flange
60
Ø 12
2x Ø 5
86,8
18,5
42,3
50
285
Probe
opening
243
34,5
4x
Ø 4,4
70
66
100
105
80
Fig. 2 Mounting position
Correct Incorrect
AIR
FLOW
AIR
FLOW
2. Having selected the appropriate mounting location, proceed with the following steps:
2.1 Drill a tight-sealing Ø 13 mm hole into the duct.
2.2 Fix the flange onto the duct outer surface using the self-drilling screws
delivered with the unit. If you do not intend to use the flange, insert the
probe and fix the enclosure onto the duct. Mind the airflow direction (see
Fig. 2 and Fig. 3).
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 7 - 10
back to the table of contents
Fig. 3 Mounting requirements
7,5*D(1)3,5*D
(1)D = Duct diameter
ATTENTION Installation requirements: e unit must not be installed in turbulent air zones. Ensure
sufficiently long settling zones upstream and downstream of the tapping point. A
settling zone consists of a straight section of pipe or duct with no obstructions. Avoid
installation near filters, cooling coils, fans, etc. e sensor will achieve the optimal
result when the measurement is taken at least 7,5 duct diameters downstream and
at least 3 duct diameters upstream from any turns or flow obstructions.
ATTENTION Installation of the unit near high EMI-emitting devices may lead to faulty
measurements. Use shielded wiring in areas with high EMI.
ATTENTION Keep at least 15 cm distance between the sensor lines and the 230 VAC power lines.
2.3 Install the probe at the desired depth and; in case you use the flange, fix it
via the plastic white screw in the flexible flange.
2.4 Unscrew the cover of the unit to remove it and insert the connecting cables
through the cable gland of theunit.
2.5 Crimp the RJ45 cable and plug it into the socket, see Fig.4 and section
“Wiring and connections”.
Fig. 4 Wiring and connections
3. Close the enclosure and secure it with the screws. Tighten the cable gland to
retain the IP rating of the enclosure.
4. Switch on the power supply.
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 8 - 10
back to the table of contents
5. Customise the factory settings to the desired ones via the 3SModbus software
or Sensistant (if necessary). For the default factory setting, see the Modbus
register map.
For the complete Modbus register data, refer to the product Modbus Register
Map, which is a separate document attached to the article code on the website
and contains the registers list. Products with earlier firmware versions may not be
compatible with this list.
NOTE
Optional settings
To assure correct communication, the NBT needs to be activated in only two devices
on the Modbus RTU network. If necessary, enable the NBT resistor via 3SModbus or
Sensistant (Holding register 9).
Example 1 Example 2
RX
ТX
NBT
NBT
Slave 2
Master
Slave n
Slave 1
Slave 2
Slave 1
RX
ТX
NBT
NBT
Master
Slave n
NOTE On a Modbus RTU network, two bus terminators (NBTs) need to be activated.
CAUTION Do not expose to direct sunlight!
OPERATING INSTRUCTIONS
NOTE For detailed information and settings, refer to the product Modbus register map,
which is attached to the article code on our website.
Calibration procedure:
Sensor calibration is not necessary.
All sensor elements are calibrated and tested in our factory.
Bootloader:
anks to the bootloader functionality, the unit firmware can be updated via Modbus
RTU communication. With 3SM boot Application (part of 3SM center software
suite), ‘boot mode’ is automatically activated and the firmware can be updated.
NOTE Make sure the power supply does not get interrupted during “bootload” procedure,
otherwise you risk losing unsaved data.
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 9 - 10
back to the table of contents
VERIFICATION OF INSTALLATION
If your unit does not function as expected, please check the connections.
TRANSPORT AND STOCK KEEPING INFORMATION
Avoid shocks and extreme conditions; store in original packing.
WARRANTY AND RESTRICTIONS
Two years from the delivery date against defects in manufacturing. Any modifications
or alterations to the product after the date of publication relieve the manufacturer
of any responsibilities. e manufacturer bears no responsibility for any misprints or
mistakes in this data.
MAINTENANCE
In normal conditions this product is maintenance-free. If soiled, clean with a dry or
damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these
circumstances the unit should be disconnected from the supply. Pay attention that
no fluids enter the unit. Only reconnect it to the supply when it is completelydry.
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER

www.sentera.eu
MIW-DSTHM-2-EN-000 - 05 / 05 / 2020 10 - 10
back to the table of contents
DSTHM-2
COMBINED T AND RH
DUCT TRANSMITTER