Sentiotec Komfort Small User manual

EN
KOMFORT-S
Version 12/18 item no. 1-030-276
INSTRUCTIONS FOR INSTALLATION AND USE
English
Solid wood sauna
Komfort
Small
208 x 158 x 204 cm

Table of Contents
1.  3
1.1. Tools required 4
1.2. Maintenance and cleaning 5
1.3. Disposal 5
1.4. KOMFORT SMALL parts list 6
2. Cabin installation 8
2.1. Base frame installation 8
2.2. Wall element assembly 9
2.3. Ceiling installation 14
2.4. Ventilation slit installation 16
  16
2.6. Installing accessories 19
2.7. Installing glass door 21
2.8. Installing roof trim 24
2.9. Installing ceiling cover slat 25
 26
  26
  27

EN
Instructions for installation and use p. 3/28
1. 
Read these assembly instructions carefully and keep them within reach when
using the sauna so that you can look up product information at any time.

Before you begin work, check the parts list to ensure that all the individual
parts have been delivered. If you discover any missing parts, notify your
dealer within 14 days of receiving the sauna cabin.
The room that the sauna is installed in must be dry and ensure an appropriate
amount of air circulation.
 
A minimum room height of 230 cm is required for the cabin installation work.
A distance of at least 5 cm from the wall must be maintained.
The inside of the wooden parts used must not be handled with any impreg-
nating material.
You need an assistant for the installation.
Wood is a natural product that can swell, shrink or warp, despite good stor-
age. For this reason, some force may be necessary during the installation.
 
Attention!


These assembly instructions can also be found in the downloads section
of our website: www.sentiotec.com/downloads.

Instructions for installation and use p. 4/28
1.1. Tools required
Hammer with a wooden head or a mallet
Cordless screwdriver with bits for cross-head screws and Torx
Roller tape measure
Drill bits with a diameter of 3 mm, 10 mm, 20 - 30 mm
(for sauna heater power cable)
Spirit level
1.5 mm hexagonal socket wrench
Utility knife
Ladder
Backsaw
60 cm
80 cm
100 cm
This symbol indicates tips and useful information
Pre-drill
Cut to real measurement with backsaw
Check the right angle:

EN
Instructions for installation and use p. 5/28
1.2. Maintenance and cleaning
The sauna should be cleaned with a damp cloth. Only use warm water – no
cleaning products.
We recommend heating the cabin once a month if the sauna is not used for
a long time.
Pitch pockets are not grounds for return, since they can always appear in
spruce wood and the depth at which they lie cannot be detected during
the sorting-out process.
If these are just under the surface, heat can cause them to soften and
“bleed”.
The leaking pitch can be removed with a rag soaked in acetone. If only
droplets of pitch occur, allow these to harden and then carefully scrape
them off with a knife.
1.3. 
Please dispose of packaging materials in accordance with the appli-
cable disposal regulations.
Used units contain reusable materials as well as hazardous substanc-
es. Therefore, do not dispose of your used unit with household waste,
but rather do so in accordance with the locally applicable regulations.

Instructions for installation and use p. 6/28
No. of
items Name Dimensions
1.4. 
Base frame
2 Base frame 66 x 9 x 4 cm
1 Base frame 204 x 9 x 4 cm
2 Base frame 156 x 9 x 4 cm
Wall elements
6 A/A wall elements 193 x 48 x 4 cm
3 A/B wall elements 193 x 48 x 4 cm
1 A/B ventilation element 193 x 48 x 4 cm
1 A/A electrical element 193 x 60 x 4 cm
1 Wall element with glass 193 x 60 x 4 cm
1 Door frame, no step, with Multiclips 202 x 72 x 4 cm
Ceiling elements
2 Ceiling elements 146 x 49 x 4 cm
1 Ceiling elements 146 x 48 x 4 cm

4 Ecksteher 90º 193 x 6 x 6 cm

2 Roof support slats 196 x 4 x 4 cm
2 Roof support slats 145 x 4 x 4 cm
2 Roof cover slats 192 x 1,2 x 4 cm
2 Roof cover slats 152 x 1,2 x 4 cm
2 Bench support slats 58 x 4 x 4 cm
2 Bench support slats 100 x 4 x 4 cm
2 Mounting slats for bench screen 26 x 4 x 4 cm

EN
Instructions for installation and use p. 7/28
No. of
items Name Dimensions

1 Benches 195 x 62 x 9 cm
1 Bench 195 x 53 x 9 cm
1 Backrests 190 x 26 x 4 cm
1 Bench screen 195 x 35 x 4 cm
1 Heater protection grille - lime wood 57 x 75 x 2 cm
1 Heater protection grille - lime wood 45.5 x 55 x 2 cm
1 Headrests 43 x 25 x 7 cm
1 Lamp protection grille 38 x 32 x 4 cm
1 Ventilation slit 52 x 14 x 1.5 cm
1 Floor grid 70 x 53 x 4 cm
Glass elements
1 Glass door 191.5 x 59 x 0.8 cm
Roof trim slats
1 Roof trim slat 208 x 6 x 4 cm
2 Roof trim slats 163 x 6 x 4 cm
Accessories
1 Door handle set wood/wood
1 2 door hinges 3308
1 Door magnet, sleeve plate
1 Sauna lamp
1 3 Silicon cables: 5 x 2.5 mm²
1 3 Silicon cables: 3 x 1.5 mm²
32 Cover caps
1 Installation material set
1 Installation instructions

Instructions for installation and use p. 8/28
2. Cabin installation

plans on Page 26 and Page 27.
2.1. Base frame installation
3 mm drill bit, 4 screws 4 x 70 mm

66 cm 66 cm
156 cm
156 cm
204 cm

EN
Instructions for installation and use p. 9/28
2.2. Wall element assembly
The corner posts and wall elements are connected with tongue and groove and
are screwed together. The door frame is connected to the wall elements using
“Multiclips”.

* Multiclips
A always refers to the visible side. This is labelled on the top side of the
wall elements.
* *

Instructions for installation and use p. 10/28
8 screws 6 x 120 mm
per corner post
Symbolphoto Symbolphoto

EN
Instructions for installation and use p. 11/28
Electrical element on right -
Exhaust air on rear left.
Electrical element on left -
Exhaust air on rear left.
Installing wall elements
The electrical element has drill holes for laying cables. For the position

4 screws 6 x 100 mm
Symbolphoto Symbolphoto
Symbolphoto

Instructions for installation and use p. 12/28
Remove transport strip from
the door frame
Insert door frame
Inserting the door frame
Push the corner post from above down onto the wall elements. When doing this,
ensure that the Multiclips are correctly aligned (see below). The door frame must

Multiclip

EN
Instructions for installation and use p. 13/28
Insert door frame
Screwing wall elements together
Check the right angle before screwing the wall elements together.
Observe the tip on page 4.
3 mm drill bit, 15 screws 4 x 70 mm
Wandelemente
15 Stk. 4x70
Maßstab: Letzte Änd.
Datum 08.06.2017
Gez. Schachermair
Komfort Large 208x206x204cm

Instructions for installation and use p. 14/28
2.3. Ceiling installation
Roof support slats
3 mm drill bit, 14 screws 4 x 70 mm
4 cm
Dachauflageleisten
14 Stk. 4x70
Maßstab: Letzte Änd.
Datum 08.06.2017
Gez. Schachermair
Komfort Large 208x206x204cm

EN
Instructions for installation and use p. 15/28
Ceiling elementsCeiling elements
3 mm drill bit, 12 screws 4 x 70 mm
Dachelemente
12 Stk. 4x70
Maßstab: Letzte Änd.
Datum 08.06.2017
Gez. Schachermair
Komfort Large 208x206x204cm
Symbolphoto

Instructions for installation and use p. 16/28
2.4. Ventilation slit installation
2.5. 
Bench support slats
2 screws 4 x 60 mm
3 mm drill bit, 3 screws 5 x 70 mm
3 mm drill bit, 4 screws 3.5 x 40 mm
82 cm

EN
Instructions for installation and use p. 17/28
3 mm drill bit, 3 screws 5 x 70 mm
2 screws 4 x 60 mm
Bench screen
4 screws 4 x 60 mm
1 cm

Instructions for installation and use p. 18/28
Backrests
3 mm drill bit, 3 screws 3.5 x 40 mm
approx. 25 cm

EN
Instructions for installation and use p. 19/28
2.6. Installing accessories
Sauna lamp
Insert lamp
(not included in the scope of delivery)
3 mm drill bit, 2 screws
4 screws 3.5 x 40 mm

Instructions for installation and use p. 20/28
Heater protection grille
Before installing the heater protection grille, drill the outlet for the heater
cable in the electrical element.
2 screws 3.5 x 40 mm
4 screws 3.5 x 40 mm