SereneLife SLSFE348 User manual

Models: SLSFE348
INTELLIGENT
ELECTRONIC SAFE
USER MANUAL

2
!Please do not keep emergency keys in your safe!
DIAGRAM
Dear valued customer,
Thank you for choosing our products! You’ve taken an important step in organizing and
protecting your most valued possessions. Every series of our safes is professionally made
and designed to provide safety. Please take time to read and familiarize yourself with the
proper operating procedures of your new safe presented on the following pages.
Again, thank you for choosing our products!

3
!
!
!
NOTE: Finish operation, pull out the emergency key and keep it in a safe place.
NOTE: Change the batteries when LCD displays “LO-BATTE”.
NOTE: The initial user code is “1234”, the initial master code is “123456”. If the
code is wrong , LCD displays “ERROR”,and back to “----”. If the wrong code is en-
tered 3 times consecutively, an alarm will sound for 20 seconds and the safe will
be locked out for 3 minutes. You may press the key “*” to clear any incorrect digit
you have input.
OPENING YOUR SAFE FOR THE FIRST TIME
INSERTING THE BATTERIES
OPENING THE DOOR
CLOSING THE DOOR
Upon rst opening, users should open the safe with the emergency key. The operation
in details refers to “opening the safe with the emergency key”.
• Remove emergency lock cover, then insert the emergency key, and turn it
counterclockwise.
• Turn the knob (master key) clockwise to open the door.
• Open the door with the emergency key.
• Insert 4AA batteries into the battery compartment.
• With power supply rstly, LCD scans, then displays "GOOD", and goes to sleep.
• The safe is ready.
• Press the “#” key.
• Input your user code (3 to 8 digits), then press“#”key to conrm and LCD displays“OPEN”.
• Turn the knob clockwise and open the door within 6 seconds.
• Turn the knob (master key) counter-clockwise to close the door.

4
SETTING THE MASTER CODE
SECURITY DISPLAY FEATURE
TAMPER ALARM
• With the door open, press “#”key to start the keypad, then press "0" twice, and then
press reset button once, LCD will show "------" with "BI" sounds twice.
• Input your new master code(3-8 digits), and press "#" to conrm.
• LCD will read “IN”,which means the new code is accepted successfully.
Your safe is equipped with a security display feature, using this feature means that
your code will not be displayed on screen when opening safe.
• Press “#” to startup the lock.
• Press “*” in touch screen to startup the hidden code function. Any code you input
will show “----“in the display, which can ensure your code safe.
• You can press“*” twice to cancel this function.
• You may set a tamper alarm that will sound if anyone attempts to move or attack
the safe.
• Press the “*” key, the display will show “ALERT on”.
• The safe will alarm when it is vibrated. To turn alarm o, press the “#” key, input the
current code, and then press “#” to conrm. If code is wrong though, the alarm will
stop after 20 seconds, but the warning state is not released (It will alarm once it is
vibrated).
SETTING THE USER CODE
• With the door open, press the reset button once, LCD will show “------”with“BI”sounds.
• Input your new user code(3-8 digits), press“#” key to conrm.
• LCD will read “IN” with “DI-DU” sounds, which means the new code is accepted
successfully.

5
OPENING THE SAFE IN AN EMERGENCY
MOUNTING METHOD
Upon rst receipt of the safe, or either the electronic circuit malfunction or codes un-
known. You could also use the emergency key to open the safe.
• Remove the cover of the emergency lock.
• Insert the emergency key to the key hole, turn counter-clockwise, then turn the knob
(master key) clockwise to open the door.
• Fix the safe in the place which is not easy to move.
• Drill holes for expansion bolts (or clamping screws) in the right place.
• Turn the expansion bolts counter clockwise to separate.
• Use the expansion bolts (or clamping screws) to secure the case to the wall.
• Make sure the case is mounted in place as required and then tighten all screws.
!CAUTION: Use the expansion bolt when there is a concrete wall surface. Use the
clamping screw when there is a wooden wall surface.